Parts for Ge PP975BM1BB: 01 - Control Panel & Cooktop Parts

This daughter relay board works with the oven's main control to switch power to the heating elements. Replacing a failed board restores reliable bake/broil operation when relays stop closing properly or the board is damaged. What it does:

• Receives low-voltage signals from the electronic control and energizes relays to supply power to oven heating elements
• Switches bake and/or broil circuits on and off for stable temperatures
• Common failure signs include: no heat or no preheat, intermittent/uneven heating, an element not turning on, or clicking from the control with no heat
• In some failures, an element may remain on until power is disconnected

• One relay board assembly

• Disconnect power at the breaker and allow the appliance to cool before servicing
• Access the board by removing the control panel or rear cover, depending on model
• Note/photograph wire locations; move connectors one at a time to the new board
• Handle the board by its edges to avoid static or physical damage; secure with the original hardware

This glass main top assembly replaces a damaged or worn cooktop surface to restore a smooth, heat-resistant cooking area and improve stove appearance. Fits select GE ranges and provides the finished top surface under burners and grates. What it does:

• Replaces the cracked, scratched, or discolored glass cooktop surface to restore functionality and appearance
• Provides a stable, heat-tolerant surface for burner elements and grates
• Helps prevent heat and spills from reaching internal components when properly installed
• Addresses symptoms such as visible cracks, chips, broken glass, or an uneven cooktop surface

• Disconnect power to the appliance (and gas supply if applicable) before starting service
• Handle glass with care—wear gloves and eye protection to avoid cuts from sharp edges
• Removing the existing top may require lifting burners/grates and unfastening retaining clips or screws; keep fasteners separate and reuse if in good condition

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

• 1 hold-down bracket

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

6" warmer

1200 watts

This 12-inch halogen oven element replaces a damaged baking element to restore heating for conventional halogen-equipped ovens. It provides direct radiant heat for baking and helps recover proper oven temperature and cooking performance. What it does

• Radiant halogen heating element for bake/roast functions
• Replaces cracked, burned-out, or non-heating elements
• Commonly used when oven won't reach temperature, heats unevenly, or shows no heat from the bake cycle
• Works with OEM mounting and connector styles for a direct-fit replacement

• Disconnect power at the breaker before any service to avoid shock
• Allow the oven to cool fully and wear gloves to protect hands from sharp edges and glass
• Handle the element carefully—halogen elements can be fragile and may break if dropped or flexed
• Verify secure electrical connections and proper mounting before restoring power; test oven on a short bake cycle

This support spring secures a stove/oven radiant heating element in place to keep the element aligned and stable during use, helping maintain reliable heating and prevent sagging or poor contact. What it does:

• Holds the radiant heating element firmly to the oven/range chassis for consistent heat distribution
• Prevents the element from shifting, sagging, or losing electrical contact
• Helps reduce arcing or intermittent heating caused by a loose element
• Common symptom: oven or burner element not staying seated, heating inconsistently, or visibly loose

• Disconnect power to the appliance before starting any repair to avoid shock.
• Remove oven racks and the heating element as needed for access; handle the element carefully to avoid damage.
• Replace only with the exact part; ensure the spring is seated correctly to secure the element.

This part is a replacement touch control board.If the current touch control board is malfunctioning in any way, this part can be used for replacement. It is intended for use with cooktops. This part is required for proper cooktop functionality, as it allows the user to properly control the heating of the surface element. Without this part in proper working order, the cooktop will not function as intended, if at all. It's critical that the appliance is entirely disconnected from the power source before any attempt is made to repair this part. Work gloves should always be worn to protect the hands. This is a genuine OEM part made by GE and has been sourced directly from the manufacturer. This touch control board is suitable for use on a variety of different models of ranges manufactured by a range of brands including General Electric, Hotpoint, and RCA. This is a genuine OEM part and thus is made of high-quality, durable materials.

The Clear Tape is an OEM part for GE cooktops. This specialized tape is used to secure and protect various components of the cooktop, including glass panels and control assemblies. It ensures that these components stay in place during operation and helps maintain the cooktop's structural integrity.

Causes of a bad cooktop clear tape can include exposure to high temperatures over time, wear and tear from regular use, or accidental damage during cleaning or maintenance.

Symptoms of a bad cooktop clear tape include:

• Loose or shifting glass panels
• Parts of the cooktop not staying securely in place
• Visible deterioration or peeling of the tape
• Difficulty in maintaining a stable cooktop surface

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Foam Tape is an OEM part for GE gas ranges. It serves as a sealant, ensuring a proper fit and preventing the escape of heat and gases from the range. This tape helps maintain the efficiency of the range by providing an airtight seal around various components.

Causes of a bad Foam Tape can include wear and tear over time, exposure to high temperatures, or physical damage during cleaning or maintenance. When the foam tape degrades, it can compromise the range's performance and safety.

Symptoms of a bad Foam Tape include:

• Heat escaping from the range
• Gas odors near the appliance
• Visible wear or gaps in the seal
• Decreased cooking efficiency

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement black screw used to secure interior or exterior appliance components. It provides a discrete, color-matched fastener to restore proper fit and stop rattles or loose panels. What it does

• Fastens trim, panels, brackets or control components where a small black screw is required
• Restores secure mounting to eliminate vibration, rattling or misaligned parts
• Matches finished appliance surfaces for a clean, unobtrusive look
• Simple hardware replacement for small fastener loss or damage

• One black screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver to seat the screw; avoid overtightening to prevent stripping or cracking surrounding material
• Keep track of small fasteners during disassembly and handle with care
• Replace with the exact part number if the original screw is damaged or the thread/length differs

ST10-16 X 7/16"

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

This replacement screw secures appliance components and helps keep panels, brackets, and controls firmly attached for reliable operation. It's a simple, direct fix when a mounting screw is missing, loose, or stripped. What it does:

• Fastens panels, trim, brackets or electrical components to reduce movement and rattling.
• Restores proper alignment of parts that shift when a screw is missing or worn.
• Helps maintain electrical and mechanical connections by keeping components seated.
• Common symptom: loose or vibrating panels, trim gaps, or visibly missing hardware.

• Disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Thread gently and avoid overtightening to prevent stripping the mating threads or cracking surrounding parts.
• Keep any removed hardware organized to ensure placement of all required fasteners during reassembly.

Package of 12

Black. 8-18 AB HXW 3/8

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

This standoff secures and isolates the oven power control module from the range chassis, helping keep the control electronics stable and properly spaced for safe operation. Replaces worn or broken mounting standoffs. What it does:

• Provides a stable mounting point for the power control module or control board
• Maintains proper clearance and insulation between the control and metal chassis
• Prevents movement that can cause loose connections, arcing, or intermittent control faults
• Helps reduce vibration and stress on control board components

• Disconnect power to the appliance before inspecting or replacing the standoff
• Use only the exact replacement standoff to maintain insulation and spacing
• If the control board shows damage, inspect the electronic assembly and wiring for additional issues

Cerama Bryte Cooktop Cleaner is a special cleaner designed specifically for ceramic glass and smooth-top cooking surfaces. It easily removes cooked-on foods, spills, or grease while leaving your cooktop looking like new. This product contains no abrasives or harsh chemicals, so it won’t scratch or damage your delicate cooktop surface.

To use the cleaner effectively, all you need to do is spray it onto the surface and then scrub it with a clean damp cloth. Use circular motions for best results. The product can also be used to remove baked-on foods from grates and drip pans on your stovetop. For tougher stains, let the cleaner sit for a few minutes before wiping it away.