Parts for Ge ZGU36ESL2SS: Control Panel Cooktop Parts

Burner bezel assembly for gas cooktops. Installs around the burner head to create a finished look. Replace if cracked, chipped, or discolored.

Replace a faulty cooktop control board when burners won't respond, display is blank, or Bluetooth connectivity fails. Restores electronic controls.

Control knob assembly for gas cooktops. Installs on the control panel. Replace if your original knob is cracked, broken, missing, or worn out.

Protective bumper that cushions the burner grate and prevents scratching or denting the cooktop surface. Replace if cracked, worn, or missing.

The Bridge Bumper is an OEM part for GE electric cooktops. It is a protective bumper located at the bridge that connects the front control panel area to the cooking surface. The bumper acts as a safeguard, cushioning any potential impact to the underside of the control panel. 

Causes of a bad bridge bumper include normal wear and tear, exposure to heat or moisture during cooking, or tears from impact. 

Symptoms of a bad bridge bumper include:

• Visible damage or deterioration of the bumper material  
• Exposure of raw edges that were previously covered
• Increased risk of scratches or damage to the control panel surface

This GE replacement part is also compatible with some Hotpoint, General Electric, and Kenmore electric cooktop models. Protect your appliance with this genuine OEM bridge bumper to safeguard the control panel from accidental impact.
 

Replaces a cracked, corroded, or damaged burner base on your gas cooktop or range. Routes gas from the orifice to burner ports and supports the cap.

The Base Burner is an OEM part for GE gas range and cooktops. It securely holds the burner assembly in place on the cooktop. 

Symptoms of a faulty base burner include:  

• Loose or wobbly burners that could tip or shift during cooking
• Difficulty cleaning accumulated debris from recessed areas  
• Potential gas or electric exposed connection hazards

Causes involve worn or cracked mounting brackets after years of use, missing or stripped retention screws, and impact damage to supports.

This OEM part is compatible with Hotpoint and RCA electric range brands as well.

The Surface Burner is an OEM part for GE gas ranges. As the critical surface heat is delivered through, it is exposed to extreme temperature variations during cooking.

Symptoms of a bad surface burner include: 

• Deteriorated or cracked porcelain-enamel exterior
• Warped or misshapen burner base that no longer sits flat
• Cookware that rocks or is unstable when placed on the burner 

Causes can be normal wear over many heating and cooling cycles or damage from the continuous use of larger pots that put undue stress on the burner head.

Replacing with this OEM GE part restores a stable, level cooking surface. It is compatible with Hotpoint, RCA, and Kenmore ranges as well as preventing future repairs from minor issues. Install yours today for reliable stove-top performance.
 

Center grate for 36-inch cooktops. Replace worn, cracked, or damaged grates to restore cookware support. Ensures stable pot and pan placement over burners.

Replacement griddle for gas cooktops. Installs on the cooking surface for grilling foods. Replace if your griddle is cracked, warped, or missing.

Replacement grate for gas cooktop burners. Provides stable support for pots and pans. Install when original is cracked, broken, or missing.

This cast cooktop grate supports cookware above a gas burner for stable heating and proper flame contact. It restores correct pot and pan placement so burners heat evenly and cookware sits level. What it does:

• Supports pots and pans directly over the burner for safe, stable cooking
• Positions cookware for proper flame contact to improve heating consistency
• Replaces a chipped, cracked, warped or missing grate that prevents cookware from sitting level
• Helps prevent pans from sliding or wobbling on the cooktop surface

• For safety, turn off gas and allow the cooktop to cool completely before removing or installing
• Lift old grate straight up to remove; set new grate into position, ensuring it seats flat and stable
• Clean contact surfaces on the cooktop before installing to prevent scratching or rocking
• Handle cast-iron grates carefully—they are heavy and can chip or crack if dropped

Replacement mounting screw for gas cooktops and ranges. Secures cooktop components in place. Order a new screw if yours is stripped, missing, or damaged.

Mounting screw for gas cooktops. Secures components and panels during installation. Replace if stripped, missing, or damaged during service work.

Burner head for gas cooktops and ranges. Sits on the cooktop surface and distributes flame evenly. Replace if cracked, corroded, or clogged beyond cleaning.

This glow-style oven igniter heats until it glows and lights the gas burner, allowing the oven to reach baking and broiling temperatures. Replaces a weak or broken igniter to restore reliable burner ignition and consistent heating. What it does:

• Heats to a high temperature to ignite the oven's gas burner
• Re-establishes normal oven heating when a burner fails to light
• Addresses symptoms like long preheat times, oven not reaching set temperature, or no ignition
• Works as the high-temperature ignition source for the oven burner system

• Disconnect power and shut off gas supply before beginning service
• Handle the ceramic/glass element carefully; it is fragile and can crack if dropped or touched with bare hands
• Verify proper alignment and secure mounting; loose connections can prevent ignition

Secures the igniter in its mounting bracket on gas ranges and cooktops. Replace if spring is missing, broken, or worn to restore proper igniter positioning.

This small metal clip secures the surface burner igniter in place on a gas range cooktop. It ensures the igniter stays properly positioned near the burner so it can reliably spark and light the gas. Replace this clip if your igniter is loose, misaligned, or falls out of position, which can cause inconsistent ignition or failure to light.

The Inner Cap Brass Cooktop is an OEM part for GE-sealed gas burners. Located under each burner head, it serves as the decorative protective barrier between the flame source and cooktop surface.

Symptoms of a bad inner cap brass include:

• Warped or misshapen shape from high heat exposure over time
• Heat discoloration detracting from aesthetic 
• Scratches, pitting, or burns on visible surfaces
• Failure to properly seat and seal under the burner head

Prolonged fiery combustion naturally causes metal fatigue and changes in material properties. This genuine GE replacement restores optimal heat deflection and a consistent surface level for safe and easy cleaning. Compatible GE and Monogram gas cooktop models maintain authentic factory finishes and performance.
 

The Burner Cap is an OEM replacement part for GE gas cooktops. This one is the outer part of the burner cap that sits over the inner burner head and flames on a gas cooktop burner. The cap helps protect the inner burner parts while also directing and controlling the burner flame.

Symptoms of a faulty burner cap include:

• Uneven or weak flame
• Gas leakage around the burner heads
• Difficulty in adjusting the flame intensity

A bad outer cap can occur due to wear and tear, accidental damage, or exposure to high temperatures. If you notice signs of damage, such as cracks, discoloration, or a loose fit, it may be time to replace the outer cap. Replacing this part can help improve burner performance and flame if the old cap is damaged or corroded. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Uneven flames or poor ignition? This gas burner cap distributes flame evenly and protects the burner head from spills. Simple DIY install restores heat.

The burner cap is an OEM component specifically designed for GE wall ovens and ranges. The inner burner cap is responsible for evenly distributing heat across the burner surface while protecting the burner element underneath. 

Causes of a bad burner cap can include damage from scratches or cracks that occur over time from regular use and cleaning. The burner cap material may also deteriorate due to exposure to high heat.

Symptoms of a bad burner cap include:

• Uneven or inconsistent burner performance  
• Hot spots on the burner surface
• Damage or cracking visible on the cap
• Difficulty cleaning residue or spills from the burner area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Inner Cap is an OEM part for GE gas cooktop models. It securely mounts the cooktop's control console and sealing panel. 

Causes of failure involve cracking or wear of rubber seals from long-term heat and impact exposures. Physical stresses like repeated removal/installation can also loosen fastener fittings.

Symptoms of a faulty inner cap include:

• Drafts and temperature fluctuations around control interfaces
• Loose or unstable mounting of the control console 
• Potential leaks permitting spillage into internal circuits    

This OEM part is compatible with Hotpoint and RCA gas cooktop brands as well.

Mounting screw for gas ranges and cooktops. Secures components during installation. Replace if screw is stripped, missing, or damaged during service.

Zinc-plated mounting screw for gas cooktops. Secures components and panels during installation. Replace if stripped, missing, or damaged.

Stainless steel cleaner for gas ranges and cooktops. Restores shine and removes fingerprints, smudges, and streaks from exterior surfaces.