Parts for Ge JB256DM2BB: Control Panel & Cooktop Parts

Replace cracked, chipped, or deeply scratched cooktop glass on your electric range. Restores the smooth, flat surface for burners and cookware.

Replace a cracked, broken, or loose range valve control knob. This knob installs on the control panel to adjust burner settings. Restores functionality.

Indicator light that illuminates when burners or oven are active. Replace if it stays on constantly or fails to light. Verify fit with your model number.

The Main Harness is an OEM part for GE gas ranges. It serves as the primary conductor between range components and control interfaces. 

Symptoms of a bad main harness include:

• Burners resisting adjustment or faulty temperature controls
• Igniters/lights failing to illuminate or heat elements inactive
• Entire range failing to power on or intermittently operating

Causes involve damage from excessive heat, wire insulation degradation over time, or loose terminals compromising connections.

This OEM GE part is also compatible with Hotpoint and RCA gas range models.

Provides structural support at the end of your range. Replace this support piece if the original is cracked, broken, or missing to restore stability.

Structural support bracket that secures the end of your range. Replaces cracked, broken, or missing end supports to restore stability and proper alignment.

Replacement control bracket for electric and gas ranges. Secures and supports the control panel assembly. Order a new bracket if yours is cracked or broken.

Decorative trim piece that frames the control panel on your electric range. Replace if cracked, discolored, or broken to restore a clean appearance.

This pin locator secures a hinge or shaft pin in place to keep linked appliance components aligned and operating smoothly. It's a small replacement part that restores proper positioning where a locating clip or retainer is used. What it does

• Holds a hinge, shaft, or pivot pin in place to prevent lateral movement
• Restores proper alignment of doors, panels, or linked components
• Helps stop rattling, misalignment, or binding caused by a worn or missing locator
• Works as a direct replacement for the same OEM-labeled locating clip/retainer

• One pin locator

• High-level replacement; basic hand tools usually required
• Disconnect power (and water, if applicable) before servicing appliances with electrical components
• Keep track of small parts and orientation for correct reassembly

Pivot pin that connects the oven door hinge to its mounting bracket. Replace if worn, broken, or missing to restore smooth door operation and alignment.

Cosmetic overlay for electric range control panels. Replaces cracked, worn, or faded overlays that protect electronics underneath. Direct fit installation.

Fix F2 error codes, dead oven display, or overheating issues. This oven control board manages temperature and cooking modes. DIY-friendly repair.

Covers the control panel lamp opening to diffuse light and protect from debris. Replace if broken, cracked, or missing to restore clear indicator visibility.

Burner not heating or working? This 6 inch surface burner element restores stovetop cooking. Direct replacement takes 10 minutes with no tools needed.

Support rod that props up the lift-up top on your range. Holds the top panel securely in the raised position for cleaning or servicing. Replace if bent or missing.

Range burner not heating evenly or drip bowl rusted? This 8-inch drip bowl catches spills and supports the coil element for level, reliable heating.

Fix burners that won't heat or have intermittent power with this surface unit wiring harness kit. Connects heating elements to range controls.

Fix burners that won't heat or have intermittent power with this surface unit wiring harness kit. Connects heating elements to range controls.

Houses and protects cooktop wiring connections. Replace when the original box is damaged, corroded, or missing fasteners for safe electrical connections.

Burner won't seat properly or wobbles? This receptacle clip secures the surface element connection for stable, reliable heat. Simple DIY fix.

Replacement mounting screw that secures the thermostat assembly to your range cabinet. Replace if stripped, missing, or damaged during repair work.

Burner not heating or terminal block burned? This electric range terminal block kit restores power to surface elements. Easy 10-15 minute DIY repair.