Parts for Hot Point RAS240DM2WW: Control Panel & Cooktop Parts

Replaces the flat cooktop surface that sits over the burner area. Restores a stable, finished surface when your original is cracked, warped, or damaged.

If your range burner won't turn on or adjust heat levels, this control knob restores precise temperature control. Mounts directly on the infinite switch shaft.

Replace a cracked, stripped, or missing oven temperature control knob. This white knob mounts to the thermostat shaft for precise temperature selection.

Covers the control panel lamp opening to diffuse light and protect from debris. Replace if broken, cracked, or missing to restore clear indicator visibility.

Burner won't heat or stays on high? This infinite switch restores precise temperature control to electric range surface elements. Easy DIY fix.

Burner won't heat or cycles erratically? Replace the infinite switch to restore smooth low-to-high temperature control on your range's surface elements.

Oven won't heat to the right temperature or overheats? This electric range thermostat monitors and regulates oven temperature for consistent cooking results.

Replacement mounting screw that secures the thermostat assembly to your range cabinet. Replace if stripped, missing, or damaged during repair work.

Indicator light that illuminates when burners or oven are active. Replace if it stays on constantly or fails to light. Verify fit with your model number.

This main wiring harness routes power and signals between the control and major components, restoring reliable electrical connections so the appliance responds correctly to controls and cycles. Designed to replace a worn, damaged, or burnt harness. What it does

• Carries power and control signals between the console/control board and motors, heating elements, sensors, and switches
• Replaces damaged or frayed wiring that can cause intermittent or no power to components
• Helps correct symptoms such as no-start or no-run, loss of heat, or erratic operation when caused by wiring faults
• Prevents short circuits and unreliable connections caused by broken terminals or insulation

• Disconnect all power before starting; verify power is off at the breaker or unplug the appliance
• Document or photograph original wire routing and connector orientations before removal for correct reassembly
• Route harness along original paths; secure with existing clips or fasteners to prevent chafing and heat exposure
• Inspect connectors for damage and ensure tight, fully seated connections; replace connector clips if missing or broken

This seal valve keeps the refrigerator water valve properly sealed to help prevent leaks and water damage. It restores a tight seal where the valve connects to the water line or manifold for reliable dispenser and icemaker operation. What it does:

• Replaces a worn or damaged valve seal to stop water leaks at the water valve connection.
• Helps restore proper water flow control to the dispenser and icemaker when leaks or drips occur.
• Commonly used when you notice water leaking beneath or behind the fridge, puddles under the valve area, or reduced dispenser/ice performance linked to a leak.
• Works as the sealing component between the water valve and its fittings or tubing.

• One seal valve (single replacement seal)

• Disconnect power and shut off the water supply before beginning repairs.
• The valve and fittings are dry, then remove the old seal and install the new seal in the correct orientation.
• Check all tubing and connectors for damage and replace if necessary to ensure a reliable seal.
• After installation, restore water and power, then test the dispenser/icemaker and inspect for leaks.

This 60-inch backguard replaces a damaged or missing range backguard to restore the finished look and help protect the wall behind the cooktop. It's a direct-fit exterior trim piece that keeps the area behind your range neat and covered. What it does:

• Covers the gap between the cooktop and the wall to hide wiring, vents, and mounting brackets
• Restores appearance after dents, rust, or paint damage to the original backguard
• Prevents debris and splatter from reaching the wall area behind the range
• Re-establishes the factory trim line for a finished installation

• Disconnect power to the appliance before attempting any work
• Usually installs to existing factory mounting points; alignment with cutouts may be required
• Two people are often helpful due to the part size and to avoid damage during installation
• Replacement may require original screws or mounting hardware; confirm existing hardware before starting

Single fastening screw for range components. Replaces missing, stripped, or damaged screws that secure panels, brackets, and trim pieces in place.

The 6" Surface Burner with Sensor is an OEM part for GE ranges. This part provides precise heating for cooking on your range's stovetop. The integrated sensor helps regulate the burner temperature, ensuring even and consistent cooking results.

Common causes of a bad surface burner include electrical issues, wear and tear over time, or damage from excessive heat or spills.

Symptoms of a bad surface burner with sensor include:

• Burner not heating up
• Inconsistent or uneven heating
• Burner temperature not being properly regulated
• Error codes or malfunction indicators on the range display

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Chrome drip bowl installs beneath 6-inch coil burners on electric ranges. Catches spills and drips during cooking. Replace when rusted, worn, or stained.

This 8-inch drip bowl sits beneath the surface coil on your range to catch spills and support the element. Replacing a rusted or stained bowl refreshes the cooktop and helps the coil sit level for reliable heating.

• Collects drips and boilovers under the 8-inch surface coil
• Positions and supports the element over the receptacle
• Helps keep the cooktop cleaner and easier to maintain
• Common signs to replace: heavy staining, rust/corrosion, warping, holes, or the element not sitting level

• Disconnect power and allow the cooktop to cool completely
• Lift the coil element slightly, then pull straight out of the receptacle
• Remove the old bowl, align the notch/orientation of the new bowl, and seat it flat
• Reinsert the coil element terminals fully into the receptacle and verify it sits level

This 8-inch drip bowl installs under your range burner to catch grease and spills. Replace if yours is rusted, cracked, warped, or heavily stained.

Burner won't seat properly or wobbles? This receptacle clip secures the surface element connection for stable, reliable heat. Simple DIY fix.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Positions your range handle at the correct distance from the door. Replace if worn, missing, or cracked to restore proper alignment and prevent rattling.

Burner not heating or terminal block burned? This electric range terminal block kit restores power to surface elements. Easy 10-15 minute DIY repair.