Parts for Hot Point RA720K4CT: 01 - Control Panel & Cooktop Parts

This 20-inch range top is the cooktop surface replacement that restores a flat, finished work area and provides proper support and spacing for burners and grates. It helps bring your range back to safe, even cooking performance. What it does:

• Re

Replacement metal main top for 20-inch electric ranges. Restores the cooking surface when the original is dented, cracked, rusted, or worn out.

Control knob for range burner or oven settings. Installs on the control panel. Replace if cracked, broken, loose, or missing for proper temperature control.

This is the control knob for a surface burner's mini valve. It fits over the valve stem so you can turn the burner on/off and adjust the flame level smoothly and safely.

• Rotates the burner's mini valve to control gas flow and flame size

Burner won't adjust temperature or stuck on high? This surface burner control switch restores heat control. Quick 10-minute fix with basic tools.

Burner stuck on high or won't heat? This 8-inch infinite switch controls heat output on electric ranges. Simple 20-30 minute DIY replacement.

Indicator light that illuminates when burners or oven are active. Replace if it stays on constantly or fails to light. Verify fit with your model number.

Top-heat thermostat that controls the oven's upper heating circuit to maintain proper temperature. Replacing a failing thermostat restores consistent broil/top-bake performance and helps the oven reach set temperatures reliably. What it does

• Reg

This rod main top support is the replacement support rod that helps secure the appliance's top assembly, restoring proper alignment and stability for safe, reliable operation. It's a direct-fit replacement when the original support is bent or broken. What it does:

• Supports and aligns the appliance top assembly to prevent sagging or misalignment
• Restores proper fit between top panel and adjacent components
• Helps eliminate rattling or movement caused by a damaged support rod
• Fits into existing mounting points—no modification required

• Disconnect power (and gas if applicable) before starting any repair.
• Handle panels carefully to avoid scratching; two-person lift may be needed for large tops.
• Use appropriate hand tools; follow OEM torque recommendations when re-securing fasteners.

Decorative trim piece that installs on your range to complete the finished look. Replace this part if the original trim is cracked, chipped, or missing.

Trim piece that frames the cooktop edges on your range. Replace this part if the original trim is cracked, chipped, discolored, or missing from wear.

Covers the control panel lamp opening to diffuse light and protect from debris. Replace if broken, cracked, or missing to restore clear indicator visibility.

Range burner not heating? This top surface element restores cooking power to your electric range. Direct plug-in design makes installation quick and easy.

The 6 Inch Small Drip Pan is an OEM part for GE ranges and stovetops. It is designed to sit beneath the burner element to catch spills and drips that occur during cooking. This helps keep the stovetop clean and reduces the risk of burns and fire by pre

Burner not heating or heating unevenly? This 8-inch surface element coil restores fast, reliable heat to your range's large burner. Easy DIY fix.

Replacement drip pan sits beneath the heating element on electric ranges and cooktops. Catches spills and overflow. Replaces cracked, warped, or worn pans.

Single fastening screw for range components. Replaces missing, stripped, or damaged screws that secure panels, brackets, and trim pieces in place.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Rubber grommet that cushions and secures your range door handle. Replaces worn, cracked, or missing grommets to restore snug fit and quiet operation.

Replace your worn, cracked, or missing electric range thermostat control knob. This dial installs on the control panel to adjust oven temperature settings.

Burner won't seat properly or wobbles? This receptacle clip secures the surface element connection for stable, reliable heat. Simple DIY fix.

This replacement screw secures trim and appliance panels with a compact 3/8" length and #8-18 thread, providing a simple fastener solution for loose or missing hardware. Fits a variety of appliance assemblies where short machine screws are used. What it does

• Fastens panels, trims, brackets, and small components that use #8-18 threaded holes
• Restores secure attachment for loose or rattling parts
• Replaces stripped or missing short screws to prevent gaps or movement
• Small size is suited for shallow mounting areas and sheet-metal attachments

• One screw

• Use the correct driver or bit to avoid stripping the head; a magnetic screwdriver helps with small fasteners
• Tighten until snug—do not overtighten to prevent thread damage or panel deformation
• Disconnect power to the appliance before working on internal components or near electrical connections
• Match those details for best fit and performance

Replacement cooktop guide that positions and supports the glass cooktop. Install when original is cracked, broken, or missing to restore proper alignment.

Burner not heating or terminal block burned? This electric range terminal block kit restores power to surface elements. Easy 10-15 minute DIY repair.

This 8-18 x 3/8 inch screw secures internal components in your range. Replace if the original is stripped, missing, or damaged during repairs.