Parts for Frigidaire FGMV155CTFA: Control Panel,Door Parts

This replacement OEM part is a microwave control panel. The microwave control panel is the part that houses the main button on the microwave used to adjust the main microwave commands. Luckily, replacing a control panel is a relatively simple process. To replace the control panel make sure to unplug the power chord. Use a a screwdriver to remove the upper grill on the top section of the microwave. With the microwave door open remove the mounting screws that secure the control panel. Once unfastened, lift the control panel up to release it from the microwave. Remove the wire harnesses and any individual wires attached to the old panel. Be sure to take note of their orientation. Replace the wires into the new control panel in the correct terminals. Slide the new control panel back in place and rethread the mounting screws. Secure the upper grill panel, and restore power to the appliance. This genuine replacement part is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand microwaves.

Replacement inside door panel that restores the refrigerator's inner door lining and helps secure door bins and insulation. Durable molded plastic improves interior appearance while protecting internal parts from moisture and daily wear. What it does:

• Serves as the refrigerator's inner door surface and mounting area for door shelves and bins.
• Protects insulation, wiring, and components inside the door from spills and debris.
• Replaces cracked, warped or stained inner door liners to restore a clean, finished look.
• Helps maintain proper door sealing by supporting the door structure and components.

• Disconnect power and empty the door before starting; some models require removing door shelves or the door assembly first.
• Panel may secure with screws or snap-in tabs—retain original fasteners and follow model-specific instructions.
• Handle edges carefully to avoid cuts; inspect door gasket and bin hardware after installation.

This Frame is an OEM part for Frigidaire microwaves. Designed to provide structural integrity and aesthetic appeal, this frame is a crucial component for the proper alignment and protection of the microwave's door and interface. 

The degradation of a microwave frame can occur due to physical impacts, frequent usage, material fatigue, or environmental factors. A compromised frame can affect the door alignment, sealing, and overall look of the microwave.

Symptoms of a bad frame include:

• Difficulty in opening or closing the microwave door.
• A visible gap or misalignment of the door.
• Cracks or breakages on the frame itself.
• Unusual noises when the door is in operation.
• The door not sealing properly, leading to heat loss or inefficient cooking.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

The Door Latch is an OEM part for Frigidaire microwaves. It is a component that secures the microwave door closed during cooking functions and prevents it from accidentally opening. The latch is designed with a sturdy spring-loaded mechanism to provide a secure seal around the door opening.

Causes of a bad latch can include wear and tear over time, damage from repeated use, or failure of the latch spring or locking mechanism.

Symptoms of a bad microwave door latch include:

• The door not closing or latching securely
• Difficulty or inability to lock the door closed
• The door popping or swinging open during a cooking cycle
• Reduced power or inability to operate cooking functions

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This coiled tension spring restores proper tension and movement for the appliance component it supports, helping doors, lids or moving mechanisms operate smoothly and reliably after the original spring wears or breaks. What it does:

• Provides restoring tension to return and hold moving parts (doors, lids, levers) in their correct position.
• Replaces worn or broken springs that can cause sagging, failure to stay closed, or loose/rattling motion.
• Reduces squeaks or abnormal noise caused by a compromised spring.
• Restores predictable, even movement when installed in the original mounting orientation.

• Always disconnect power (and water/gas if applicable) before starting any repair.
• Use appropriate tools and wear eye protection; springs can store tension and may release suddenly.
• Note the spring's orientation and attachment points before removal so the replacement installs the same way.

The Microwave Door Handle is an OEM part for Frigidaire microwaves. It provides the grasping point that allows access to the microwave cavity. 

Causes of a bad handle can be normal wear over many cycles of use. Physical damage from impacts or accidental mishandling can also cause issues.  

Symptoms of a bad microwave door handle include:

• The handle being difficult to open the microwave door
• The handle not staying in the open or closed position
• Looseness or wobbling of the handle
• Cracks or breaks in the plastic housing

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.