Parts for Ikea 20462165: Control Panel, Door Parts

A full replacement refrigerator door assembly that restores proper closure, appearance, and function. Replaces damaged, dented, or misaligned doors to help maintain internal temperature and food safety. What it does:

• Replaces a worn, cracked, or dented refrigerator door to restore a proper seal and appearance
• Helps stop cold air leaks that can cause inconsistent cooling or higher energy use
• Replaces a door with broken latch or hinge attachment points so the door opens and closes correctly
• Restores integrated trim, inner liner, and mounting points as built by the manufacturer

• Disconnect power to the appliance before starting any repairs
• Handle with care; parts may include glass, trim, or painted surfaces that can scratch or chip
• Support the cabinet and door during removal/installation to avoid strain on hinges and fasteners
• Re-check door alignment and gasket seal after installation; adjust hinges per OEM instructions if needed

Replacement inside door panel that restores the refrigerator's inner door lining and helps secure door bins and insulation. Durable molded plastic improves interior appearance while protecting internal parts from moisture and daily wear. What it does:

• Serves as the refrigerator's inner door surface and mounting area for door shelves and bins.
• Protects insulation, wiring, and components inside the door from spills and debris.
• Replaces cracked, warped or stained inner door liners to restore a clean, finished look.
• Helps maintain proper door sealing by supporting the door structure and components.

• Disconnect power and empty the door before starting; some models require removing door shelves or the door assembly first.
• Panel may secure with screws or snap-in tabs—retain original fasteners and follow model-specific instructions.
• Handle edges carefully to avoid cuts; inspect door gasket and bin hardware after installation.

This Frame is an OEM part for Frigidaire microwaves. Designed to provide structural integrity and aesthetic appeal, this frame is a crucial component for the proper alignment and protection of the microwave's door and interface. 

The degradation of a microwave frame can occur due to physical impacts, frequent usage, material fatigue, or environmental factors. A compromised frame can affect the door alignment, sealing, and overall look of the microwave.

Symptoms of a bad frame include:

• Difficulty in opening or closing the microwave door.
• A visible gap or misalignment of the door.
• Cracks or breakages on the frame itself.
• Unusual noises when the door is in operation.
• The door not sealing properly, leading to heat loss or inefficient cooking.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

The Door Latch is an OEM part for Frigidaire microwaves. It is a component that secures the microwave door closed during cooking functions and prevents it from accidentally opening. The latch is designed with a sturdy spring-loaded mechanism to provide a secure seal around the door opening.

Causes of a bad latch can include wear and tear over time, damage from repeated use, or failure of the latch spring or locking mechanism.

Symptoms of a bad microwave door latch include:

• The door not closing or latching securely
• Difficulty or inability to lock the door closed
• The door popping or swinging open during a cooking cycle
• Reduced power or inability to operate cooking functions

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This coiled tension spring restores proper tension and movement for the appliance component it supports, helping doors, lids or moving mechanisms operate smoothly and reliably after the original spring wears or breaks. What it does:

• Provides restoring tension to return and hold moving parts (doors, lids, levers) in their correct position.
• Replaces worn or broken springs that can cause sagging, failure to stay closed, or loose/rattling motion.
• Reduces squeaks or abnormal noise caused by a compromised spring.
• Restores predictable, even movement when installed in the original mounting orientation.

• Always disconnect power (and water/gas if applicable) before starting any repair.
• Use appropriate tools and wear eye protection; springs can store tension and may release suddenly.
• Note the spring's orientation and attachment points before removal so the replacement installs the same way.

This holder is a small mounting clip used to secure components inside the appliance, helping keep internal parts stable and reducing noise from loose fittings. It's a straightforward replacement when the original clip is broken or missing. What it does:

• Secures panels, trim, or small assemblies to prevent shifting or rattling
• Restores proper alignment of the component it supports
• Commonly replaced when cracked, deformed, or lost during service
• Helps reduce vibration-related noise from loose parts

• One holder as pictured

• Turn off power to the appliance before servicing to avoid shock or injury
• Remove surrounding trim or panels as needed to access the mounting location
• Confirm orientation and engagement before snapping into place; do not force if misaligned