Parts for Ikea 20462165: Oven,Cabinet Parts

A full replacement refrigerator door assembly that restores proper closure, appearance, and function. Replaces damaged, dented, or misaligned doors to help maintain internal temperature and food safety. What it does:

• Replaces a worn, cracked, or dented refrigerator door to restore a proper seal and appearance
• Helps stop cold air leaks that can cause inconsistent cooling or higher energy use
• Replaces a door with broken latch or hinge attachment points so the door opens and closes correctly
• Restores integrated trim, inner liner, and mounting points as built by the manufacturer

• Disconnect power to the appliance before starting any repairs
• Handle with care; parts may include glass, trim, or painted surfaces that can scratch or chip
• Support the cabinet and door during removal/installation to avoid strain on hinges and fasteners
• Re-check door alignment and gasket seal after installation; adjust hinges per OEM instructions if needed

Replaces cracked, burned, or missing waveguide cover in your microwave. Protects the magnetron opening from food splatter and moisture damage.

This is a small support bracket that holds the cooking rack or shelf in place inside the microwave. It mounts to the interior cavity wall and keeps the shelf level during use. Replace this part if your microwave shelf is wobbly, tilting, or no longer stays in position.

This is a rear shelf support bracket that holds the cooking rack in place inside the microwave. It clips or mounts to the interior cavity wall to keep the rack level and stable during use. Replace this support if it is broken, missing, or if the cooking rack wobbles or will not stay in position.

This base is the lower cabinet support and trim piece that secures the appliance's kickplate and helps keep the cabinet level and stable. It restores proper fit and prevents debris from collecting under the unit. What it does

• Provides structural support for the appliance's lower cabinet and kickplate
• Secures the toe kick and helps maintain correct appliance clearance
• Helps reduce vibration and movement at the base of the appliance
• Prevents dirt and debris from entering under the cabinet
• Commonly replaced when the lower trim is cracked, broken, or missing

• One base piece as shown

• Disconnect power and water before starting work
• Remove the toe kick/trim and any mounting screws to access the base
• Use basic hand tools; handle edges carefully to avoid cuts

Grease filter for range hoods and over-the-range microwaves. Dimensions: 5-1/16" x 7-5/8" x 3/32" (5.0625 x 7.625 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

Restores the outer trim around your microwave door. Replaces cracked, warped, or damaged frame pieces that secure door glass and keep components aligned.

Clear plastic lens cover for microwave interior or hood lights. Snaps over bulb assembly. Replace when cracked, yellowed, or missing. Easy DIY fix.

Microwave not heating or display not working? This control transformer supplies low-voltage power to electronic components. Moderate DIY repair.

Microwave not heating food? The magnetron generates the microwaves that cook your food. A failed magnetron is the most common cause of no-heat issues.

This replacement motor restores power to the appliance's fan or blower assembly so airflow and cooling performance resume. Use it to replace a failed or noisy motor and get your appliance running normally again. What it does

• Spins the fan/blower or driven component to circulate air or operate the mechanism.
• Replaces motors that stall, hum, or do not run at all.
• Can resolve reduced airflow, warm compartments, or uneven cooling when motor failure is the cause.
• Designed to match the appliance's original motor function and mounting.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Verify the motor part number and physical fit against the unit before installation.
• Basic hand tools required; access may require removing panels or shelves.

This high voltage capacitor works with the diode and magnetron to generate the microwave energy needed to heat food. It stores and releases electrical energy to nearly double the voltage output from the transformer. Replace this capacitor if the microwave runs but does not heat, makes a loud buzzing noise, or if the unit trips a breaker - always discharge the capacitor before handling as it can retain a dangerous charge even when unplugged.

Microwave not heating or making buzzing noises? This diode rectifier allows current flow in one direction and protects circuits. DIY repair takes 30 minutes.

Microwave won't turn on or keeps losing power? This power cord restores the electrical connection. Fixes worn or damaged cords causing failures.

The Thermostat is an OEM part for Frigidaire microwaves. The thermostat accurately monitors interior temperature levels during operation.

Symptoms of a faulty thermostat include:

• Inconsistent or uneven cooking results from inaccurate sensing  
• Continuous running even after the set time elapses
• Error lights or temperature faults displayed 

Failure usually occurs due to a gradual loss of calibration from years of thermal cycling stress or corrosion buildup damaging electrical components. Replacement is needed to restore precise temperature regulation.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models. 

This thermostat monitors the internal temperature of the microwave and helps regulate heating to prevent the appliance from overheating. It acts as a safety device that cuts power to certain components if temperatures exceed safe limits. Replace this thermostat if the microwave shuts off unexpectedly during use, fails to heat properly, or if diagnostic testing shows the thermostat is no longer opening or closing at the correct temperature.

This thermostat is a temperature-sensing switch used in select appliances to control operation or provide over-temperature protection. It opens or closes the circuit at a calibrated point to help maintain proper, consistent performance. What it does

• Senses temperature at its mounting/location and switches contacts at a set point
• Regulates cycling of the system or ends a heating/cooling/defrost event as designed
• Helps prevent overheating or overcooling conditions and protects components
• Supports stable, reliable operation when the original thermostat fails

• Runs continuously or won't cycle off
• Shuts off too soon or won't turn on
• Inconsistent temperature (too warm/too cold)
• Erratic cycling or failure to maintain set temperature

• 1 thermostat

• Disconnect power before servicing; allow any hot surfaces to cool
• Note wire positions; move leads one at a time to the new thermostat
• Mount in the original location and orientation; ensure firm contact/fit
• Route any sensing bulb/capillary exactly like the original; avoid kinks

This mechanical thermostat controls refrigerator temperature by sensing evaporator or cabinet temperature and switching the compressor and fans on and off. Replaces a worn or faulty control to help restore consistent cooling and temperature regulation. What it does

• Senses temperature and closes/open circuit to run the compressor and cooling fans
• Helps maintain set temperature by cycling refrigeration system components
• Commonly linked to symptoms like warm or fluctuating temperatures, compressor not running, or continuous running
• Works as the control point for user temperature settings

• One thermostat

• Disconnect power to the appliance before accessing controls to avoid shock or injury
• Access may require removing interior panels or control housing
• Handle sensing bulb and capillary tube carefully to avoid kinks or damage

This is a humidity sensor that detects moisture levels inside the microwave cavity during cooking. It works with the control board to automatically adjust cook times and power levels when using sensor-based cooking modes. Replace this sensor if the microwave overcooks or undercooks food on auto-sensor settings, or if you receive a sensor error code on the display.

Fix an air conditioner that won't start or runs poorly. This compressor start/run capacitor restores motor operation and improves cooling performance.

Microwave turntable not rotating? This turntable motor drives the rotating glass tray. Common fix for plates that won't spin during heating cycles.

The fuse is a protective link in the appliance's power circuit. When excessive current or a short is detected, it opens the circuit to help safeguard wiring and electronics. A blown fuse often leaves the unit completely unresponsive.

• Interrupts power during an overcurrent or short to prevent further damage
• Helps protect control boards, motors, and wiring
• Typical symptoms: no power, blank display/controls, won't start
• Tests open (no continuity) when blown

• Disconnect power at the breaker or unplug before servicing
• Replace only with the same type and rating specified by the manufacturer
• If a new fuse blows again, locate and correct the underlying short or failed component before further use
• For microwave repairs, high-voltage capacitors can retain a dangerous charge.

This is an electrical noise filter designed to suppress electromagnetic interference generated by the microwave's internal components. It connects inline with the power supply to prevent electrical noise from affecting the microwave's operation or other nearby electronics. Replace this filter if your microwave displays erratic behavior, produces unusual buzzing sounds, or interferes with other appliances on the same circuit.

The Lamp is an original and genuine OEM replacement part for Frigidaire microwaves. It is located inside the microwave and provides light to easily see food and monitor cooking progress.

Causes of a bad lamp can be natural bulb burnout over time, damage from foods accidentally jostling the lamp during cooking, or general wear and tear.

Symptoms of a bad lamp include:

• Dimming or flickering light inside the microwave when in use
• No light turning on when the microwave is powered on
• Broken or cracked bulb housing

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Microwave tripping breaker or won't start? A faulty door switch is often the cause. This safety switch detects door position. Moderate DIY repair.

This is a small microswitch used in the microwave's door interlock system or control mechanism. It detects whether the door is properly closed and signals the unit to allow or prevent operation for safety. Replace this switch if the microwave does not start when the door is closed, runs with the door open, blows a fuse repeatedly, or fails to respond when buttons are pressed.

Microwave tripping breaker or won't start? A faulty door switch is often the cause. This safety switch detects door position. Moderate DIY repair.

This is a cooling fan motor used in a microwave oven to circulate air and prevent internal components such as the magnetron and electronics from overheating. It typically runs during cooking and may continue running briefly after the microwave shuts off. Replace this motor if the microwave is overheating, shutting off unexpectedly, or if the fan is noisy, runs sluggishly, or doesn't spin at all.

This fan blade mounts to the refrigerator fan motor to move air through the appliance for proper cooling and temperature circulation. Replaces a worn or damaged blade to restore airflow and improve cooling efficiency. What it does:

• Spins on the fan motor to circulate air across the evaporator or condenser coils
• Restores proper airflow when a cracked or broken blade causes reduced cooling
• Helps stop vibration or rattling caused by bent or missing blades
• Can reduce motor strain from an imbalanced or damaged blade

• Disconnect power to the appliance before starting any repair
• Remove access panels and fan shroud to reach the blade; keep track of mounting hardware
• Replace carefully to avoid bending the blade; ensure correct orientation on the motor shaft

Mounting bracket for microwave ovens. Secures the unit to wall or cabinet. Replace if bent, cracked, or missing to ensure safe installation.

This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.

• Transfers motion from the door-open button to the latch hooks to release the door
• Helps resolve a door that won't open when the button is pressed
• Addresses a button that feels loose, sticks, or lacks resistance
• Replaces a cracked or broken lever causing intermittent door operation

• Unplug the microwave and discharge the high-voltage capacitor before servicing
• Remove the grille and control panel to access the interlock/latch area
• Note spring and pivot orientation and transfer any reusable hardware
• Test door release action before completing reassembly

Retainer bracket for microwaves. Secures internal components in place. Replace if broken, cracked, or missing to restore proper fit and stability.

Secures internal components to the microwave chassis. Replace if cracked, broken, or missing to restore proper support and stop rattling or misalignment.

This outer cabinet is the main housing that supports and encloses the refrigerator compartment, restoring the unit's structural support and finished appearance. Replaces a damaged, dented, or corroded outer shell to help maintain proper door alignment and insulation coverage. What it does

• Provides the main structural enclosure for the refrigerator, holding interior components in place.
• Restores a smooth exterior surface and protects internal insulation from moisture and damage.
• Helps maintain proper door alignment and sealing by supporting hinge and trim locations.
• Addresses symptoms such as visible dents, rusted or damaged outer panels, or gaps between panels and trim.

• One outer cabinet housing (quantity: 1), as specified by the OEM part number.

• Disconnect power and remove food from the appliance before beginning work.
• Cabinet replacement may require removal of doors, trim, and internal components.
• Use proper lifting assistance and protective gloves—cabinet panels can be large and have sharp edges.

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged

Controls airflow through your microwave's ventilation system. Installs at exhaust opening to prevent air backflow. Replace if cracked, missing, or damaged.

This is a vent damper door used in the microwave's exhaust system. It opens to allow steam and cooking fumes to vent outside and closes to prevent outside air from flowing back in. Replace this part if the damper is stuck open or closed, if you hear rattling from the vent area, or if you notice poor ventilation or backdrafts during cooking.

Replacement turntable coupler for microwaves. Connects the carousel plate to the motor shaft. Replace if cracked, broken, worn, or missing. Easy DIY.

Support ring installs beneath the microwave turntable to provide stable, balanced rotation. Replace if cracked, broken, or missing for proper use.

Molded protective housing cover that shields internal microwave components from dirt and debris. Replace if cracked, broken, or missing to maintain safety.

Directs hot air and steam away from your microwave during cooking. Replace when clogged with grease or cracked around screw supports. Verify fit with your model.

Rear wall mounting bracket that securely attaches your microwave to the wall or cabinetry. Replace if your original bracket is missing, cracked, or damaged.

The Mounting Kit is an OEM part for Frigidaire microwaves. It provides the necessary hardware to mount a built-in microwave securely above a cooktop or range. The mounting kit contains mounting brackets, and screws to facilitate a safe and sturdy installation. This kit does not include the installation instructions.

Causes of a bad mounting kit can include deterioration of mounting brackets or screws over time and repeated use, or if the original kit was missing components needed for a secure installation.

Symptoms of a bad or missing mounting kit include:

• The microwave become loose or detached from the wall
• Screws fall out or strips during installation
• Brackets bend or break over time
• Microwave is not level after installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a metal cooking rack designed to fit inside a microwave oven, providing an elevated surface for multi-level cooking or reheating. It allows you to heat multiple dishes at once by utilizing the upper portion of the microwave cavity. Replace this rack if it is bent, corroded, or if the protective coating has worn off, which can cause arcing or uneven cooking.

Keep your microwave's ventilation performing its best. This replacement air filter helps screen cooking vapors before the air is recirculated or exhausted, restoring proper airflow and helping maintain cleaner, more effective ventilation.

• Filters air drawn through the microwave's ventilation system during cooking
• Helps reduce cooking odors and airborne particles in the exhaust stream
• Supports proper airflow and fan performance for effective venting
• Replace when saturated, damaged, or visibly dirty; do not operate without required filters
• Common signs of a spent filter: persistent odors, weaker ventilation, or a discolored/brittle filter

• Disconnect power by unplugging the unit or switching off the circuit breaker before service
• Access the filter from the underside panel or top/front grille, per your model
• Note the old filter's orientation; install the new filter the same way and secure any tabs or screws
• Ensure all panels/grilles are reinstalled securely before restoring power

This molded air flow deflector directs cold air inside the freezer or refrigerator compartment to promote even cooling and prevent frost buildup on stored items. It's a straightforward replacement that restores proper airflow without tools in many installs. What it does:

• Channels cold air where the appliance design intends so temperature stays consistent across shelves and drawers
• Helps reduce localized warm spots and uneven cooling caused by a cracked or missing deflector
• Keeps air from blowing directly on food, which can cut down on frost and moisture issues
• Works with the freezer/refrigerator evaporator/air distribution system to maintain designed performance

• One deflector

• Disconnect power or unplug the appliance before starting any repair
• Remove shelves or panels as needed for access; handle plastic parts carefully to avoid cracking
• Install by aligning tabs/slots and snapping or fastening per the appliance's layout; do not force parts into place
• If airflow problems persist after replacement, check the evaporator fan and air damper for proper operation

Replacement air vent grille for microwaves. Mounts to the cabinet to direct airflow. Needed when the original grille is cracked, broken, or missing.