Parts for Ge CGS975SED4SS: Control Panel, Gas & Burner Parts

Replace your range's RF filter harness to restore proper electromagnetic interference suppression. Essential when experiencing radio frequency issues. Verify fit with your model number before ordering.

Stainless steel cleaner for gas ranges and cooktops. Restores shine and removes fingerprints, smudges, and streaks from exterior surfaces.

Replace a cracked, stripped, or missing range control knob. Restores reliable temperature and burner setting selection with secure, tactile control.

Replace your range manifold panel if burner controls are loose, the control panel is damaged, or knobs don't align properly. Fits select gas range models.

Size: 8 - 32 inch.

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

Secures the cooktop to the range frame, preventing shifting or rocking. Replace if your bracket is cracked, bent, worn, or missing for stable alignment.

Protective cover that slips over the gas valve shaft to shield valve components from spills, food debris, and moisture. Replace if cracked or missing.

This replacement pan-head screw is used in refrigerators to fasten panels, brackets, and covers so they stay tight and properly aligned. Replace a missing or damaged screw to restore a solid, rattle-free fit.

• Secures interior/exterior panels, brackets, trim, and covers
• Replaces missing, stripped, or corroded hardware
• Helps maintain proper alignment of attached components

• Disconnect power before servicing; shut off water if working near water lines
• Match location to the original fastener and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal

• Thread size: #8-18 (type AB)
• Length: 1/2 inch
• Head style: Pan head, Phillips drive

Replacement mounting screw that secures the thermostat assembly to your range cabinet. Replace if stripped, missing, or damaged during repair work.

Secures the burner valve assembly to your gas range. Replace this mounting screw if worn, missing, or stripped to restore proper valve alignment and support.

This is a natural-gas orifice and burner tube assembly for the rear right burner that controls gas flow for proper ignition and flame size. Replaces a worn or clogged orifice to restore reliable burner performance. What it does:

• Meters and directs natural gas from the valve to the rear right burner for consistent ignition
• Helps maintain correct flame size and even heating at the burner
• Commonly used when flame is weak, uneven, or the burner won't light reliably
• Works with compatible gas cooktop/range rear-right burner assemblies

• One natural gas orifice and tube assembly for the rear right burner

• Turn off the gas supply and disconnect power before servicing
• Use appropriate wrenches and avoid overtightening; fittings are typically threaded
• Do not modify the orifice or use for conversions unless specified by manufacturer

Replace your range bake burner when oven won't heat, bakes unevenly, or takes too long to preheat. Moderate DIY repair with basic hand tools required.

Restores proper gas flow when burners won't light or flame is weak. This supply tube connects the valve to the burner for reliable ignition and heat.

Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.

Dual cavity elbow connector for ranges. Installs between dual oven cavities to route airflow. Replace if cracked, broken, or missing to restore proper fit.

Fix uneven browning or weak broiling with this oven broil burner. Restores high-temperature top-down cooking for proper searing and browning.

Protective shield that covers the oven igniter. Replace if cracked, broken, or missing to shield the igniter from spills, drips, and falling debris.

Burner orifice spud regulates gas flow to the burner on your range or cooktop. Replace if missing, damaged, or when converting between LP and natural gas.

Weak or uneven flames on your gas range? A clogged or damaged orifice spud restricts gas flow to the burner. Simple replacement restores proper flame size.

Fix uneven flames or weak burner heat with this range burner orifice spud. Controls gas flow to each burner. Simple DIY repair in 15-20 minutes.

Fix burners that won't light, stay lit, or shut off completely with this gas control valve. Regulates flow to a single burner for steady flames and safe cooking.

Fix an oven that won't heat, displays error codes, or has an unresponsive control panel. This electronic control board restores temperature regulation.

Burners won't ignite or flame is weak? This gas valve controls fuel flow to your range burners. Restores reliable ignition and steady flame performance.

Fix an oven that won't heat or takes too long to reach temperature. This igniter glowbar opens the gas valve to ignite the burner. DIY-friendly repair.

The Oven Igniter is an OEM replacement part for GE ovens, designed to ignite the bake igniter to start the heating process. This part is responsible for creating the spark that ignites the gas, providing the heat needed to cook and bake food. Over time, the oven igniter can wear out or become damaged, which can prevent the oven from heating.

Symptoms of a bad Oven Igniter include:

• The oven not heating up at all.
• The oven taking longer than normal to heat.
• Gas smell in the oven due to gas being released without ignition.
• A clicking sound without the oven igniting.

Causes of a bad igniter can include normal wear and tear over time, exposure to excessive heat or moisture, or physical damage from impact or mishandling.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

IMPORTANT: The connector plug may need to be cut off and igniter wires connected to range wires using porcelain wire connectors.

Burner deflector guard for gas ranges. Installs around burner assembly to direct heat and protect components. Replace if cracked, warped, or missing.

This broil shield protects the oven interior above the broiler, helping direct heat and shielding the oven cavity from intense broiling temperatures for safer, more consistent broiling results. Durable metal construction resists warping. What it does:

• Shields the oven top and components from direct broiler heat to prevent damage and discoloration
• Helps maintain more even broiling by directing heat where food is placed
• Reduces the risk of flare-ups reaching wiring or insulation behind the oven liner
• Restores proper clearance between the burner and oven liner for safe operation

• One broil shield

• Disconnect power (and gas, if applicable) and allow the oven to cool completely before starting
• Remove oven racks and access the broiler area to unfasten and replace the shield using basic hand tools
• Inspect mounting tabs and surrounding liner; replace any damaged clips or screws as needed

Range control knob assembly for adjusting burner and oven temperature settings. Replace if knob is cracked, faded, loose, or missing from your range.

Fix an overheating oven with this range limit thermostat. Stops heating when temperatures exceed safe limits. Straightforward repair for most DIYers.

This tangential blower is the oven cooling fan assembly that moves air across the cavity and control area to help regulate temperature and prevent overheating. It restores proper airflow for safer, more consistent oven operation. What it does:

• Circulates air across the oven cavity and control electronics to help dissipate heat
• Prevents control board and components from overheating during use
• Reduces hot spots and helps maintain more even cooking temperatures
• Often linked to symptoms like loud or unusual fan noise, the fan not spinning, or oven components running hotter than normal

• One tangential blower assembly

• Disconnect power to the appliance before starting any repair
• Handle carefully; fan blades and sheet-metal openings can be sharp
• Verify fan rotation direction and mounting orientation before final reassembly

Decorative trim skirt that fits around range control knobs on the front panel. Replace if cracked, disintegrating, melted, or missing for a clean look.

Fix unresponsive touch controls or cracked glass on your range. This assembly combines the glass cover and circuit board to restore full control functionality.

Flow deviator guard for ranges. Shields and directs airflow within the appliance. Replace if cracked, broken, or missing to restore proper assembly.

Fix gas smell when range is off with this safety valve lockout clip. Secures gas valve actuator to prevent unintended movement. Simple DIY repair.