Parts for Crosley CLCG500FW3: Control Panel Parts

The Rotary Knob is an OEM part for Frigidaire laundry centers. It's a key component allowing users to select and control different settings and cycles on their laundry appliances.

Causes of a bad Rotary Knob can include continuous use leading to wear and tear, which may result in a loose fit or difficulty in turning the knob. Accidental damage, such as cracking or breaking if hit or dropped, could impair its functionality.

Symptoms of a malfunctioning Rotary Knob include:

• Difficulty in selecting cycles or settings due to a loose or stiff knob.
• Inability to start the laundry center if the knob cannot engage the necessary settings.
• Visible signs of damage or wear that prevent the knob from functioning properly.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.

• Provides an electrical on/off signal to the control or safety circuit
• If faulty, selected functions may not activate or may be intermittent
• Can trigger error codes related to a switch input, depending on model

• Disconnect power before servicing; turn off gas/water if applicable
• Note/photograph wire locations and transfer connectors one at a time
• Verify actuator alignment and secure mounting before reassembly
• After installation, run a test cycle to confirm proper operation

The Washer Timer is an OEM part for Frigidaire washing machines. It controls the sequence of operations in the washing machine, including filling, washing, rinsing, and spinning. By managing the timing of these cycles, the timer ensures the washer operates efficiently and effectively.

Causes of a bad washer timer can include electrical malfunctions, wear and tear from regular use, or physical damage to the timer mechanism. Power surges, exposure to moisture, and accidental impacts can also lead to timer failure.

Symptoms of a bad Washer Timer include:

• Washer not advancing through cycles
• Machine getting stuck on a single cycle
• Incorrect timing for washing, rinsing, or spinning
• Washer not starting or completing a cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This push start switch is the user-operated momentary button that completes the start circuit so the appliance begins its cycle. It replaces a worn or unresponsive start button to restore reliable start control. What it does:

• Acts as a momentary contact to send the start signal to the control
• Commonly used when the appliance does not begin a cycle after pressing the start button
• Can fail from wear, corrosion, or broken actuator, causing no response or intermittent starts
• Works with the factory wiring and mounting for direct replacement

• One push start switch

• Always disconnect power to the appliance before performing service
• Handle terminals carefully; ensure secure, corrosion-free connections
• Test the switch for continuity with a meter after installation and before restoring full use

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

White. Left hand side

The Dryer Timer Knob is an OEM part for Frigidaire dryers. It is responsible for allowing users to set the drying time and cycle selection by turning the timer shaft. The knob securely attaches to the timer and provides an easy way to control dryer settings.

Over time, the timer knob can become damaged due to repeated use, excessive force when turning, or wear on the internal connection points. If the knob becomes stripped, cracked, or no longer stays in place, it may need to be replaced.

Symptoms of a bad timer knob include:

• The knob spins freely without adjusting the timer
• Cracks or breaks in the knob
• Difficulty selecting or changing dryer settings
• The knob does not stay attached to the timer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement mounting screw that secures appliance panels, trim or brackets to restore proper fit and reduce rattles. A simple fastener that helps keep components stable for safe, quiet operation. What it does:

• Secures panels, trim pieces or internal brackets in place
• Replaces lost, stripped or damaged screws that cause loose parts
• Helps stop rattling, vibration or misaligned panels
• Restores proper alignment so doors and covers sit flush

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten — snug until secure to prevent damage
• Disconnect power before working near electrical components
• Keep small parts away from children and pets

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

White. Right hand side

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Hex washer head ,10-32 x 0.375. Ground

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.