Parts for Electrolux EFLW427UIW0: Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is the main electronic control board that manages the washer's cycles, timing, and user interface functions. It receives input from the control panel and sends signals to the motor, valves, and other components to run each wash cycle. Replace this board if the washer displays error codes, buttons become unresponsive, cycles fail to start or complete, or the display is blank or flickering.

Replacement mounting bracket that secures panels, assemblies, or controls to your washer cabinet. Needed when original is cracked, broken, or missing.

Fix E11 error code and washer not filling issues. This pressure sensor switch monitors water levels and signals the control board. DIY repair in under an hour.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Fix a washer that won't start, stops mid-cycle, or has a blank display with this main control board. Controls all washer functions and cycles.

Front console panel that houses the control interface and buttons. Replaces cracked, warped, or visibly damaged outer panel to restore a clean surface.

This is the handle attached to the detergent dispenser drawer on a front-load washing machine. It allows you to pull the drawer open to add detergent, fabric softener, or bleach. Replace this handle if it is cracked, broken, or has snapped off, making it difficult to open the dispenser drawer.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement mounting screw that secures panels, brackets, and components to your washer chassis. Replaces missing, stripped, or damaged screws.

This is a flexible hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. If you notice detergent not dispensing properly, leaking near the dispenser area, or water pooling under the washer during the fill cycle, this hose may be cracked, clogged, or disconnected and needs replacement.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Secures wiring and hoses to your laundry center frame. Replace if cracked, broken, or missing to keep wire bundles organized and protected from wear.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

Fix a washer that won't fill or fills slowly with this water inlet valve. Controls hot and cold water flow into the tub. Direct replacement part.

Replaces cracked, worn, or leaking internal water hose in your washer. Restores watertight water flow between drum and dispenser components.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Replacement housing for washer detergent dispenser assembly. Installs in the top front panel. Order if your original housing is cracked, broken, or missing.

The Housing is an OEM part for Frigidaire washers. It holds the dispenser cup securely in place and ensures proper functioning of the detergent and fabric softener dispensing system.

This housing is specifically designed to fit within your Frigidaire washer, providing stability and support to the dispenser cup. It helps prevent leaks and ensures that the detergent and fabric softener are dispensed accurately during the wash cycle.

A bad housing can be caused by wear and tear, damage, or improper installation. Signs of a faulty lower housing include leaks, loose dispenser cup, or improper dispensing of detergent or fabric softener.

Symptoms of a bad housing include:

• Leaks or drips from the dispenser
• Loose or wobbly dispenser
• Improper dispensing of detergent 

Replace your defective or damaged housing with this genuine OEM Frigidaire part to restore your washer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This is the detergent and fabric softener dispenser drawer assembly for a washing machine. It slides in and out of the front of the washer, holding separate compartments for detergent, bleach, and softener that are dispensed at the appropriate times during the wash cycle. Replace this drawer if it is cracked, missing internal dividers, stuck, or no longer dispensing products correctly.

Fix detergent or fabric softener not dispensing properly with this washer dispenser cup assembly. Restores proper distribution of laundry products.

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.