Parts for Electrolux FFLE1011MW2: 04 - Control Panel Parts

This electronic control board is the appliance's central circuit board, interpreting inputs and directing power to key components. Replacing a failed board can restore normal operation, responsive controls, and consistent performance after erratic, dead, or intermittent behavior.

• Processes user inputs and sensor signals to coordinate functions
• Manages timing, indicator/display logic, and safety interlocks as designed
• Distributes power to loads
• Common failure symptoms: no power/display, unresponsive buttons, random cycling/beeping, or error codes

What's included: 1 electronic control board Install notes:

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use anti-static protection
• Photograph wiring and transfer connectors one at a time to the new board
• Some models require programming or a diagnostic reset; follow the unit's tech sheet/service manual

This replacement control knob lets you operate the corresponding control on your appliance with a solid, accurate feel. Restore clean appearance and dependable adjustment if the original knob is cracked, loose, missing, or stripped.

• Attaches to the control shaft to select and adjust settings
• Replaces knobs that are broken, cracked, or won't stay on the stem
• Helps correct slipping/spinning that prevents proper selection
• Restores pointer alignment and smooth, positive engagement

• Disconnect power (and shut off gas if applicable) before servicing
• Pull the old knob straight off the control shaft—do not pry against the panel
• Align the new knob with the shaft and press firmly until fully seated
• Test the control for proper engagement and pointer alignment before use

The Cycle Selector Switch is an OEM part for Frigidaire washers and dryers. It is a component that allows you to choose and control different cycles and settings during the laundry process. The cycle selector switch is typically located on the control panel of the washer or dryer.

Causes of a faulty cycle selector switch can include regular wear and tear, electrical malfunctions, or physical damage. These factors can result in issues such as the switch not responding or functioning properly, difficulty in selecting or changing cycles, or the appliance not starting or stopping as desired.

Symptoms of a bad cycle selector switch may include:
Inability to select or change cycles
Unresponsiveness or inconsistency in switch operation
Error codes or failure to start or stop the appliance

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This wiring harness routes power and control signals between components to restore electrical connections and reliable operation. It replaces a damaged or worn harness to help eliminate intermittent power or non-functioning circuits. What it does:

• Transfers power and signals between the control board, motors, switches, and sensors
• Restores connections when plugs, wires, or terminals are broken, corroded, or shorted
• Helps stop intermittent operation, no-power conditions, or components that don't respond
• Provides factory-style connectors and routing for proper fit and function

• Disconnect all power before starting any repair to avoid shock or injury
• Compare the harness to the original and route and secure wires the same way to prevent pinching or rubbing
• Handle connectors by the housings; avoid pulling on wires to prevent damage
• Replace the entire harness rather than attempting partial repairs

This factory electrical switch opens and closes a control circuit inside select laundry appliances. Replacing a worn or failed switch restores consistent signaling so the assigned function operates reliably and the machine responds as expected.

• Opens/closes electrical contacts when actuated by the appliance's control, lever, or mechanism
• Provides the on/off or position signal needed by the timer or electronic control
• Common symptoms of a failing switch: no response when selecting an option, intermittent operation, or an option that engages only when wiggled
• May trigger a related fault or cause the cycle to pause/stop when the switch is moved, depending on model

• Disconnect power before servicing; also shut off gas supply
• Access the switch per your model's service information; avoid pulling on wires
• Note and transfer wire positions one-by-one (take a photo for reference)
• If diagnosing, verify switch continuity with a multimeter before and after replacement

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.