Parts for Electrolux FFLE1011MW2: 05 - Lower Cabinet / Top Parts

Mounting screw for laundry center panels and components. Replace missing, stripped, or damaged screws to secure parts properly during assembly or repair.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

Top-loading washer lid for laundry center units. Replace if cracked, bent, or no longer closes securely. Installs with hinge screws at the rear.

Washer won't start or door won't close properly? This door striker secures your laundry center lid. Simple 2-screw replacement takes 10 minutes.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Replacement pin for washer components. Secures and connects internal parts. Needed when original pin is broken, missing, or worn from use.

Base for your washer. This structural component supports the machine and installs at the bottom. Order a replacement if your original is cracked or damaged.

Fix a washer that won't start or respond to controls with this main motor control board. Controls drive motor speed and direction. Moderate difficulty.

Cushion bumper for washer dryer combo units. Installs to absorb vibration and reduce noise. Replace if cracked, worn, or missing for proper support.

Fix a washer that only fills with cold water or won't fill at all. This water inlet valve controls hot and cold water flow during wash cycles.

Shipping block for washers, installs inside cabinet to secure the tub during transport or moving. Replace if lost, broken, or missing from original packaging.

Secures interior trim and components in your laundry center to prevent rattling and shifting. Replace when worn or broken to restore a snug fit. Verify compatibility with your model number.

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

Replace your laundry center control panel when buttons don't respond or the console is cracked. Houses buttons, switches, and display for reliable operation.

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.

Small alignment pin that positions and secures panels or components during assembly. Replace when worn, missing, or damaged to restore proper fit.

This is a replacement 12-24 UNC machine screw used to secure appliance panels and internal components so fittings stay tight and stable during use. It restores proper fastening where the original screw is damaged or missing. What it does:

• Fastens and secures panels, brackets, and component assemblies
• Helps stop rattling, loose parts, or gaps caused by a missing or stripped screw
• Provides correct thread engagement for 12-24 UNC threaded holes
• Replaces worn, rusted, or damaged screws to restore original fit

• Disconnect power and water to the appliance before servicing
• Use the correct driver and size to avoid stripping the head
• Thread in by hand first, then tighten snugly—do not overtighten
• Replace only with the exact part number to ensure proper fit and function

This washer door lock secures the door closed and communicates locked status to the control so cycles can run safely. Replacing a failed lock restores proper latching and may resolve no-start, spin, or door/lock error issues.

• Locks the door at the start of the cycle to prevent opening during wash and spin
• Signals the control when the door is closed and locked
• Releases the door at the end of the cycle
• Common symptoms: won't start, door won't lock/unlock, intermittent pauses, door/lock error message

• Unplug the washer before servicing
• Access the lock from the front; remove the door gasket clamp and mounting screws (procedure varies by model)
• Transfer wires to the new lock one connector at a time; do not force terminals
• Verify the door striker engages smoothly and test an empty cycle before full use

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Control panel for laundry center units. Replaces damaged, cracked, or broken front panel housing controls. Installs on exterior front of unit.

The Dispenser is an OEM replacement part for Frigidaire washing machines. Located on the interior door, the dispenser accurately releases detergent, softener, and other treatments through a series of internal chambers and slots directly into the wash drum.

Causes of failure include clogging of internal dispenser parts from built-up detergent, damaged outlets preventing proper release into the drum, worn gears interfering with controlled dispensing timing, or electronic control issues disrupting the sequenced release.  

Symptoms of a bad dispenser include:

• Products not fully dispensing or spraying inside the wash drum as intended
• Residue buildup inside dispenser compartments  
• Loose, sagging, or missing internal dispenser components
• Premature dispensing during water fill instead of correct cycle times

This OEM Frigidaire component is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a small spring that attaches to the lid of a laundry center washer, providing tension to hold the lid in position. It helps the lid stay open during loading and close securely during operation. Replace this spring if your washer lid won't stay open, slams shut on its own, or the original spring is broken or stretched out.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.