Parts for Electrolux FFLE1011MW2: 06 - Motor / Tub Parts

This replacement cover restores the protective barrier over its designated area on your appliance. It helps shield internal components from debris and moisture while maintaining a secure fit and finished appearance.

• Protects internal parts by covering the opening and helping keep out debris and moisture
• Restores proper fit and finish when the original cover is cracked, warped, or missing
• Reduces rattling or vibration caused by a loose or broken cover
• Common signs it's needed: visible damage, broken/missing tabs, or a cover that won't stay in place

• Disconnect power before servicing; also shut off the water supply
• Note the orientation and any fastener locations before removal
• Reuse original screws/fasteners and transfer any clips or seals from the old part if designed to
• Ensure the cover seats fully and do not overtighten to avoid damage

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This pressure sensor monitors system pressure and sends pressure feedback to the control board so the appliance can manage cooling cycles accurately. Replacing a faulty sensor helps restore proper pressure feedback and reliable cooling performance. What it does:

• Monitors internal refrigeration pressure and provides sensor feedback to the control board.
• Helps the control board regulate compressor and cooling cycles based on pressure readings.
• A failing sensor can cause erratic cooling, extended run times, or error/fault codes.
• Works as a direct replacement sensor—the control system relies on accurate readings to operate normally.

• Disconnect power to the appliance before starting any service.
• Handle the sensor and wiring harness gently; avoid pulling on wires or connectors.
• Replace with the exact part number and secure all connections; improper wiring can cause faults.

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

This replacement hose routes water between internal components in your washer, maintaining a secure, leak-resistant connection. Replace a cracked, swollen, or brittle hose to stop leaks and restore proper water flow during cycles.

• Directs water between specific components inside the washer for proper water movement throughout the cycle
• A failing hose can present as water on the floor, moisture inside the cabinet, or intermittent cycle interruptions
• Age, vibration, heat, and detergent/chemical exposure can cause rubber to crack, swell, or soften
• Inspect for kinks, abrasions, or loose/damaged clamps; replace at the first signs of wear to prevent leaks

• Disconnect power and turn off the water supply before servicing; allow the appliance to cool
• Keep towels or a shallow pan ready to catch residual water when removing the old hose
• Photograph hose routing and clamp placement; transfer or replace clamps as needed
• Push the hose fully onto each barb and seat clamps behind the bead; run a short test and check both ends for leaks

The Trunnion is an OEM part for Frigidaire washing machines. It allows the outer wash tub to rotate during agitation and the spin cycles. The trunnion is a heavy-duty, durable component designed to withstand the rigors of repeated cycles and turbulent wash motions.

Causes of a bad trunnion can be wear over extended use, damage from unbalanced loads that strain the pivot point, or fractures from impact or manual mishandling.

Symptoms of a bad trunnion include:

• Excessive vibration or shaking during operation
• Noisy or grinding sounds emanating from the tub area
• Difficulty starting or stopping tub motions
• The tub failing to rotate properly during cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small rubber mounting grommet that cushions and secures appliance components to reduce vibration and protect wiring or mounts from chafing. Replaces a worn or missing grommet to restore proper fit and quiet operation. What it does

• Cushions and isolates panels, brackets, or wiring to reduce noise and vibration.
• Protects cables and hoses from rubbing against metal edges.
• Helps keep components aligned by providing a snug, flexible mount.
• Common symptom: noise, rattling, chafing marks, or a loose fit where a grommet is missing or deteriorated.

• One rubber grommet as shown.

• High-level task; verify power is off and the appliance is disconnected before accessing the area.
• Inspect surrounding clips, screws, or wiring for damage and replace if needed.
• Push into the mounting hole until fully seated; ensure the mating component fits securely over the grommet.

This genuine replacement spring restores proper tension and smooth movement in the affected mechanism, helping your appliance operate reliably. Replacing a weakened or broken spring can reduce noise and correct misalignment caused by lost tension.

• Maintains tension and provides return force for connected levers, brackets, or linkages
• Helps keep components in position and minimizes excess play or rattling
• A weakened, stretched, or broken spring can cause poor engagement or inconsistent operation
• Common signs include parts not returning to rest, excess slack, or new noises from the area

• Disconnect power; also shut off water supply
• Note the spring's hook orientation and routing; take a reference photo before removal
• Control the spring with pliers and wear gloves/eye protection to avoid snap-back injuries
• Inspect related brackets/retainers and replace any worn components to ensure proper tension

This replacement belt links the drive motor to the appliance's drive system so the drum or tub can rotate during operation. Replacing a stretched, cracked, or broken belt restores proper movement and reduces slippage and noise.

• Transfers motor rotation to the drum or tub to enable tumbling or spinning
• Common symptoms: drum/tub not turning, intermittent movement, or cycle runs but contents don't tumble/spin
• Squealing, thumping, or burning-rubber odor from belt slippage
• Visible fraying, glazing, or cracks on the belt surface

• Disconnect power and allow the unit to cool before servicing
• Note belt routing/tension before removal; take a photo for reference
• Inspect idler/tensioner and motor/drum pulleys; replace worn components to prevent premature belt wear
• After installation, hand-rotate the system to verify alignment and tracking before test run

The Water Inlet Valve is an OEM part for Frigidaire washing machines. This part controls the flow of water into the washer tub during the fill and rinse cycles.

Causes of a bad Water Inlet Valve can include sediment buildup or obstructions, electrical or solenoid issues, or physical damage from water pressure or wear over time.

Symptoms of a faulty Water Inlet Valve include:

• Washer not filling with water or filling slowly
• Overfilling or flooding of the washer tub
• Leaks around the valve or water inlet area
• Loud humming or buzzing noises during fill cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Frigidaire Drain Pump is an OEM part for Frigidaire washing machines. It plays a crucial role in the washer's operation by removing water from the wash tub at the end of each cycle, ensuring your clothes are properly drained before the spin cycle. 

Causes of a bad drain pump can include blockages from debris such as coins, lint, or small items that escape from clothing, as well as motor or impeller damage. Electrical failures can also impair pump function, leading to inadequate water removal.

Symptoms of a bad Frigidaire Drain Pump include:

• Water not draining completely from the washer
• Unusual noises, like humming or buzzing, indicating the pump is struggling
• Washer stopping mid-cycle
• Water pooling around the base of the machine

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drain Hose is an OEM part for Frigidaire washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle.

You should replace the drain hose if it becomes damaged or clogged. Causes of a bad drain hose include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

Tub to pressure switch hose.

This is a 5/16-18 UN machine screw used to fasten appliance components and trim securely. It provides a reliable threaded connection to keep panels, brackets, and assemblies in place during normal use. What it does:

• Secures panels, trim, brackets, and internal components to the appliance frame
• Restores proper fit when a missing or stripped screw causes gaps or rattling
• Maintains alignment of parts to prevent vibration and wear
• Matches standard 5/16-18 UN threads for replacement where that thread is specified

• Disconnect power and follow the appliance manufacturer's safety instructions before working on the unit
• Use the correct driver/socket to avoid stripping the head or damaging the screw
• Tighten until snug; avoid over-tightening which can strip threads or crack parts
• Replace with the same thread size and type (5/16-18 UN) for proper fit

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

This small retainer clip secures trim, panels or wiring harnesses so components stay aligned and rattle-free during use. It's a simple replacement that restores proper fit and helps prevent loose parts from shifting or rattling. What it does

• Holds panels, trim or harnesses in place to prevent movement and vibration
• Stops rattling or buzzing caused by loose fasteners or trim
• Keeps electrical wires routed and secured to reduce strain
• Restores proper fit where a broken or missing clip allowed gaps or play

• Basic snap-in installation; remove trim or access panel as needed to reach the clip location
• Inspect mating holes and surrounding plastic or metal for damage before installing
• Use moderate finger pressure or appropriate pliers — avoid over-forcing to prevent breaking the new clip
• Disconnect power if working near electrical components or wiring

A small replacement retainer clip used to secure interior trim or components so panels and shelves stay in place. Replacing a worn or broken clip restores a snug fit and reduces rattling or loose parts. What it does

• Holds trim, panels or small components in place to prevent shifting
• Prevents rattling and keeps parts aligned for proper operation
• Replaces cracked, broken or missing clips that allow parts to sag or fall
• Works wherever the OEM clip design is specified for a secure snap-fit

• Clip

• Disconnect power before servicing appliances with electrical components
• Remove surrounding trim or components carefully to access clip location
• Press or snap the clip into place; avoid forcing to prevent damage
• Keep small parts away from children and pets during installation

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.