Parts for Frigidaire FLXE52RBT5: 04 - Control Panel Parts

The Dryer Timer is an OEM part for Frigidaire dryers. It is responsible for controlling the drying cycles by regulating the amount of time the dryer runs. The timer ensures that clothes are dried according to the selected settings, contributing to efficient and effective drying performance.

Causes of a bad timer can include electrical issues such as a short circuit, worn-out internal components due to frequent use, or exposure to moisture that can damage the timer mechanism.

Symptoms of a bad Dryer Timer include:

• The dryer not advancing through cycles
• The dryer running continuously without shutting off
• Inconsistent drying times
• The timer knob not turning or feeling loose

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This genuine OEM part is a timer for washers. The timer is the part that allows the washer to start and stop after being in use for a amount of time. The settings of the timer are controlled by the user and will adjust automatically depending on the desired settings. If the washer is no longer stopping after the desired time has elapsed, the timer might need to be replaced. To replace the timer, start by making sure the washer is unplugged. After that, pull the washer away from the wall to access the back panel. Once accessed, remove the screws that attach to the back panel and locate the timer. Once located, remove the mounting screws that hold it in place. Proceed to pull the timer out of the washer, and replace it with the new part. This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This push start switch is the user-operated momentary button that completes the start circuit so the appliance begins its cycle. It replaces a worn or unresponsive start button to restore reliable start control. What it does:

• Acts as a momentary contact to send the start signal to the control
• Commonly used when the appliance does not begin a cycle after pressing the start button
• Can fail from wear, corrosion, or broken actuator, causing no response or intermittent starts
• Works with the factory wiring and mounting for direct replacement

• One push start switch

• Always disconnect power to the appliance before performing service
• Handle terminals carefully; ensure secure, corrosion-free connections
• Test the switch for continuity with a meter after installation and before restoring full use

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

Color: white. Measures about 2 inches in diameter.

Replacement mounting screw that secures appliance panels, trim or brackets to restore proper fit and reduce rattles. A simple fastener that helps keep components stable for safe, quiet operation. What it does:

• Secures panels, trim pieces or internal brackets in place
• Replaces lost, stripped or damaged screws that cause loose parts
• Helps stop rattling, vibration or misaligned panels
• Restores proper alignment so doors and covers sit flush

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten — snug until secure to prevent damage
• Disconnect power before working near electrical components
• Keep small parts away from children and pets

PPH ab st/z/ch `6 - 18x.60

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip