Parts for Frigidaire FWX445RFT1: 05 - Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Replace your washer's timer knob if it's cracked, broken, or missing. This control knob attaches to the timer shaft, allowing you to select wash cycles.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replace your washer's timer dial knob if it's cracked, broken, or missing. This control knob installs on the timer shaft to select wash cycles and settings.

This right-side almond end cap restores the finished look of the appliance trim and protects the exposed end of the handle/door trim from wear. It provides a neat, color-matched replacement for damaged or missing trim. What it does:

• Covers and protects the exposed end of the handle or door trim to prevent further damage
• Restores a finished, color-matched appearance for almond-colored appliances
• Helps keep dirt and moisture out of the trim end, preserving fit and alignment
• Replaces cracked, broken, faded, or missing end caps that affect appearance

• Disconnect power or unplug the appliance before beginning work.
• Remove any screws or trim pieces holding the old end cap in place; the cap typically snaps or fits into position.
• Align the new cap and press or fasten per the original mounting method; do not force or overtighten fasteners.
• If mounting clips or fasteners are damaged, replace them before installing the new cap.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Cushioning spacer pad that supports and separates internal washer components. Replace if cracked, compressed, or missing to restore proper spacing.

Cushioning spacer pad that supports and separates internal washer components. Replace if cracked, compressed, or missing to restore proper spacing.

This component adjusts the tension of washer suspension springs in laundry center units and is located within the suspension system. Replace when experiencing excessive vibration, unbalanced loads, or unusual movement during spin cycles.

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.