Parts for Ge PT925SN4SS: 01 - Control Panel Parts

This control display module is the oven/range user interface that shows status and accepts touchpad or button commands, restoring visible controls and responsive operation for affected units. What it does:

• Displays oven settings, clock, temperatures and error codes so you can monitor cycles
• Receives keypad or touch inputs to set bake, broil, timers and other functions
• Helps the range respond when buttons are unresponsive or the screen is blank
• Can resolve intermittent control behavior or incorrect readouts related to the console

• One control display module (user interface) as shown

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the glass and ribbon/pin connectors carefully to avoid damage
• Remove the console or trim to access the module; keep fasteners and grounding intact
• Verify the part number on your existing module before ordering and test operation after reconnecting power

This slider assembly base supports and guides a refrigerator/freezer drawer so it opens and closes smoothly. It replaces worn or broken slider bases to restore proper drawer alignment and movement. What it does:

• Provides the base support for the drawer slide mechanism to ensure smooth opening and closing
• Replaces cracked, broken or worn plastic slider components that cause sticking or uneven travel
• Helps prevent the drawer from falling out or binding during use
• Works with the existing slide/rail hardware to maintain proper alignment

• Disconnect power or remove food and follow manufacturer safety instructions before working in the appliance
• Remove the drawer and any trim to access the slider area; installation typically involves snapping or fastening the slider into place
• Inspect mating slide/rail components and replace any damaged clips or screws for a secure fit

This slider assembly base supports and guides a refrigerator/freezer drawer so it opens and closes smoothly. It replaces worn or broken slider bases to restore proper drawer alignment and movement. What it does:

• Provides the base support for the drawer slide mechanism to ensure smooth opening and closing
• Replaces cracked, broken or worn plastic slider components that cause sticking or uneven travel
• Helps prevent the drawer from falling out or binding during use
• Works with the existing slide/rail hardware to maintain proper alignment

• Disconnect power or remove food and follow manufacturer safety instructions before working in the appliance
• Remove the drawer and any trim to access the slider area; installation typically involves snapping or fastening the slider into place
• Inspect mating slide/rail components and replace any damaged clips or screws for a secure fit

A door handle spacer that fits behind a range of GE appliance handles to ensure correct fit and alignment, restoring a snug, finished appearance. Helps keep the handle positioned and prevents contact rubbing. What it does:

• Positions the door handle at the correct distance from the door surface for proper fit and operation
• Helps prevent handle wobble, rubbing, and cosmetic gaps
• Supports secure attachment of the handle to the door assembly
• Useful when replacing a damaged or missing spacer during handle repair

• One door handle spacer

• Install with the handle hardware in the correct order; confirm orientation before tightening
• Use proper-size screwdrivers; avoid over-tightening fasteners to prevent cracking the spacer
• Disconnect power or follow appliance-specific safety instructions when working near electrical components or heating elements
• Replace those components as well for a reliable repair

Upper window pack assembly that replaces a cracked or damaged refrigerator door window panel, restoring appearance and helping protect the components behind the outer window. What it does:

• Replaces the upper door window pack to restore a clear, finished exterior on the appliance door.
• Addresses visible damage symptoms such as cracked, scratched, cloudy or broken window panels.
• Protects internal door components from exposure to moisture and debris.
• Matches the OEM-style mounting points for a like-for-like replacement when used with the correct model parts.

• Disconnect power and remove food from the door area before starting any repair.
• Handle the window pack carefully; wear cut-resistant gloves and eye protection when removing broken or cracked pieces.
• Remove any trim or fasteners per the appliance's service instructions; retain mounting screws and gaskets as needed.
• Refer to the OEM service manual or diagram for model-specific removal and reassembly steps.

A single mounting screw used to secure panels and components on compatible GE appliances. This genuine-fit fastener keeps parts firmly attached so panels and assemblies stay aligned and function safely. What it does:

• Secures trim, panels, brackets, or small components in place
• Restores loose or rattling panels caused by missing or stripped screws
• Helps maintain proper alignment of service panels and assemblies
• Prevents vibration-related noise from unsecured parts

• Use the correct size screwdriver or bit to avoid stripping the head
• Hand-start threads, then tighten securely but avoid overtightening to prevent damage
• If working near electrical components, disconnect power before servicing
• If a screw was stripped or the mounting hole is damaged, replace with the correct fastener size

This is a truss-head screw used to fasten appliance panels and trim securely. It provides a low-profile, wide bearing surface to hold components in place and resist pull-through. What it does:

• Fastens trim, access panels, brackets, and lightweight components
• Wide truss head spreads load to prevent damage to thin sheet metal
• Replaces missing or stripped screws that cause loose panels or rattling
• Maintains proper alignment of cosmetic and service panels

• One truss-head screw (8-32 x 0.343 in)

• Use the correct #2 Phillips driver; a magnetic bit helps hold the screw
• Tighten snugly but avoid overtightening to prevent thread or panel damage
• Disconnect power before removing or working near electrical components
• If threads are damaged, replace with the exact part rather than reusing with thread repair

ST10-16 X 7/16"

This silicon controlled rectifier (SCR) is an electronic switching component that controls current flow in appliance control circuits, helping regulate power to heaters, motors, or other loads for stable operation. What it does:

• Switches and regulates current in control boards and power circuits
• Can prevent power from reaching a heater, motor, or element when failed
• Helps protect downstream components by controlling surge/current flow

• Disconnect power to the appliance before servicing to avoid shock.
• Handle the SCR carefully to avoid electrostatic discharge (ESD) damage.
• May require board-level replacement or soldering skills.

A small replacement spring wiper that restores proper contact pressure and wiping action on the appliance component it services. Replaces a worn or broken wiper spring to help maintain consistent performance and reliable operation. What it does:

• Provides tension and a wiping contact surface where the original spring wiper has worn or failed
• Restores consistent electrical/contact or mechanical wiping action that can affect operation
• Commonly replaced when loose, bent, broken, or when intermittent contact is observed
• Helps prevent arcing, poor contact, or inconsistent component movement when functioning correctly

• One spring wiper

• Evaluate the surrounding components and match before installing; replace only the part(s) explicitly specified
• Use proper tools and avoid bending or overstretching the spring during installation
• Disconnect power to the appliance before accessing or replacing electrical/contact components

This 10-32 machine screw secures brackets, panels, and other hardware in cooking appliances. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned and safely fastened. What it does:

• Fastens panels, brackets, and components using a 10-32 machine thread
• Replaces hardware that is missing, rusted, or stripped
• Helps address loose or rattling parts and minor panel misalignment
• Maintains secure mounting after service or part replacement

• One 10-32 machine screw

• Disconnect power; for gas appliances, also shut off gas before service
• Support the panel or bracket while removing/installing hardware
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace them one at a time to keep alignment