Parts for Ge JS750DF4WW: Control Panel Parts

Control panel assembly for electric ranges. Houses touchpad interface and display. Replace if cracked, unresponsive, or display is damaged or illegible.

If your range display is blank, shows error codes, or won't maintain temperature, the control board is likely failed. DIY repair in 30 minutes.

White graphics overlay faceplate for range control panels. Replaces worn, faded, or peeling control panel graphics. Adhesive decal restores appearance.

Replace your range's control panel faceplate if the overlay is cracked, scratched, faded, or peeling. Installs over the control board for a clean finish.

Fix a burner stuck on high, won't heat, or indicator light stays on. This infinite control switch regulates surface burner temperature. 20-minute repair.

Burner stuck on high or won't adjust temperature? This range infinite switch controls surface element heat levels. Common DIY fix for uneven heating.

Seals your electric range faceplate to prevent moisture, dust, and debris from entering. Replace when worn or damaged to restore a snug fit. Confirm fit.

Range burner won't shut off or heat properly? The infinite switch controls burner temperature. DIY-friendly repair takes about 15-20 minutes.

Seals the console to keep moisture, grease, and debris from reaching electronics. Replace if crushed, torn, or allowing contaminants in. Confirm fit.

Replace your cracked or faded control panel insert to restore your range's appearance and protect controls. Trim piece allows panel lighting through. Verify fit with your model number before ordering.

Secures the small clear lens in your range's control panel opening. Replace if cracked, broken, or missing to restore a snug fit and proper appearance.

Replace a cracked, stripped, or missing range control knob. This round dial restores manual operation of cooktop or oven temperature settings.

Indicator light for range control panels. Illuminates to show when burners or functions are active. Replace when dim, flickering, or burned out. Verify fit with your model number.

Secures the clear lens on your range's control panel. Replace if cracked, broken, or missing to keep the lens properly seated and prevent shifting or rattling.

Replace a cracked or discolored indicator light lens to restore clear status visibility on your range. This snap-in lens covers the panel light opening. Confirm fit with your model number.

This wire harness connects the infinite burner control to the cooktop's wiring, restoring proper electrical routing for surface element regulation. It replaces a damaged or worn harness to help re-establish safe, reliable burner control. What it does:

• Provides the correct wiring connection between the infinite switch and cooktop terminals.
• Restores electrical continuity when a frayed, burned, or disconnected harness prevents burner operation.
• Helps eliminate intermittent or no-heat symptoms caused by broken wires or loose terminals.
• Maintains OEM routing and connector fit for consistent control response.

• One wire harness for infinite control (exact OEM configuration)

• Disconnect all power to the range at the breaker before starting work.
• Handle connectors gently; use proper tools to release terminals without bending.
• Verify proper connector seating and secure routing away from heat sources before restoring power.
• If terminals or the infinite switch show damage, replace the affected components as recommended.

This wire harness connects the infinite control switch to the cooktop wiring, restoring proper electrical connection so the surface burner control responds correctly. Designed to replace damaged, burned, or frayed switch wiring. What it does:

• Carries power and control signals between the infinite (surface burner) control switch and the cooktop wiring.
• Helps stop intermittent burner operation, loss of heat control, or no power to a burner when the harness is damaged.
• Replaces melted, cracked, or corroded wires and connectors that cause arcing or unreliable switch function.
• Matches OEM connector types and routing so the switch operates as intended.

• Disconnect power to the appliance before inspecting or replacing the harness to avoid shock or injury.
• Route and secure wiring away from hot surfaces and moving parts; avoid pinching or sharp bends.

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it co

Mounting screw secures panels, trim, and internal components in ranges and ovens. Replace if missing, stripped, or damaged to restore proper fit.

Replacement mounting screw for securing panels, trim, and internal brackets. Needed when original fasteners are missing, stripped, or damaged.

Black. 8-18 AB HXW 3/8

Range burner clip secures burner components in place. Replace if bent, broken, or burners wobble. Verify fit with your model number before ordering.