Parts for Gibson GGR442AS0: 07 - Control Panel Parts

The Timer Knob Assembly is an OEM replacement part for Frigidaire electric dryers. This assembly incorporates the timer dial, stem, and mounting components that allow users to set desired drying periods.

Causes of a faulty timer knob include wear and tear of internal gears from regular cycle selections. Damage to the outer dial or stem connection points may also occur.

Symptoms include: 

• Inability to rotate timer dial through full drying options   
• Timer selections not initiating or maintaining set programs
• Dial detaching from the front panel during adjustment

This OEM Frigidaire replacement part is compatible with Electrolux, Gibson, and various Kenmore dryer models as well.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

The Turn Start Switch is an OEM part for Frigidaire dryers. It is responsible for initiating the drying cycle when the switch is turned. This switch is a critical component that engages the dryer’s motor and starts the drying process, ensuring your clothes are dried effectively.

You should replace the turn start switch if it becomes faulty or unresponsive. Causes of a bad start switch can include regular wear and tear from frequent use, electrical issues, or damage due to excessive force or mishandling.

Symptoms of a bad turn start switch include:

• Dryer not starting when the switch is turned
• Intermittent starting issues
• The switch feeling loose or not engaging properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Temperature selector switch.

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This 18" trim plate restores the finished look along the appliance front, covering gaps and worn edges for a clean, built-in appearance. It replaces damaged or missing trim to refresh the unit's visible surface. What it does:

• Covers the gap between the appliance and surrounding cabinetry for a seamless look
• Protects the appliance edge from chips, scratches and everyday wear
• Restores appearance when original trim is dented, bent or discolored
• Helps maintain a consistent trim line around the control/door area

• Disconnect power to the appliance before starting any work.
• Handle trim carefully—edges may be sharp; wear gloves as needed.
• Remove any fasteners or adjacent panels to access mounting points; reuse existing screws unless replacements are specified.
• Align trim to the mounting locations and fasten without over-tightening to avoid warping.

Color: White

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support