Parts for Kenmore 417.41102000 (41741102000, 417 41102000): Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Mounting bracket for washer and laundry center models. Secures components in place during operation. Replace if cracked, bent, or broken to restore stability.

A small replacement retaining ring that secures internal components to restore proper alignment and reliable operation. Use this OEM-style ring when a worn or broken ring lets parts shift or rattle. What it does

• Holds shafts, trim, or small assemblies in place to prevent movement and rattling
• Helps maintain proper alignment of the associated component
• Can stop intermittent contact or noise caused by a loose part
• Prevents parts from slipping out of position during normal use

• Disconnect power (and water supply if applicable) before beginning any repair
• Access the affected assembly per your model's service instructions or diagram
• Use appropriate pliers or a small driver to remove and install the ring; avoid forcing parts
• Inspect surrounding seals, clips, and fasteners and replace any damaged items

This replacement pipe routes water where needed inside the appliance to restore proper flow and stop leaks. It's a direct-fit service tube for systems that use molded or bent piping to move water. What it does

• Channels water between internal components to enable normal operation
• Helps prevent water leaks and pooling when intact
• Commonly replaced when cracked, split, clogged, or disconnected
• Can resolve symptoms like visible leaks, water on the floor, or components not filling properly

• One replacement pipe

• Recommended for customers comfortable with basic appliance disassembly; refer to your model's service manual or IPL for the exact routing and clip locations
• Disconnect power and water supply before starting repair to avoid shock or flooding
• Inspect mounting clips, grommets, and seals and replace any damaged hardware to ensure a secure, leak-free fit

If your washer won't start, displays error codes, or cycles incorrectly, the electronic control board may have failed. This board manages all functions.

Fix a washer that won't fill, overfills, or shows E35 error code with this water level pressure switch. Moderate DIY repair takes about 1-2 hours.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

The Water Dispenser Valve is an OEM part for Frigidaire washing machines. This valve controls the flow of water into the washing machine during the wash and rinse cycles. It ensures that the correct amount of water enters the drum, contributing to efficient and effective cleaning.

Causes of a bad water dispenser valve can include mineral deposits or debris clogging the valve, wear and tear over time, or electrical faults that affect the valve’s operation. 

Symptoms of a bad water dispenser valve include:

• No water entering the washer
• Insufficient water during cycles
• Leaks around the valve area
• Inconsistent water flow

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replaces cracked, worn, or leaking internal water hose in your washer. Restores watertight water flow between drum and dispenser components.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Rubber O-ring seal prevents water leaks at hose connections and fittings. Replace when worn or cracked to restore tight seal and stop dripping. Verify fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.