Parts for Kenmore 417.99576100 (41799576100, 417 99576100): Control Panel Parts

The Start Switch is an OEM replacement part for Frigidaire dryers. This part initiates the dryer's cycle once the user selects the desired settings. By pressing the start switch, the motor activates, and the drying process begins, ensuring clothes are dried according to the selected specifications.

Symptoms of a bad Start Switch include:

• The dryer not starting when the switch is pressed
• Intermittent starting issues, where the dryer sometimes starts and sometimes doesn’t
• The need to hold the switch in place to keep the dryer running
• Unusual noises when the switch is pressed

Causes for a malfunctioning Start Switch can include electrical issues, such as faulty wiring or connections, wear and tear from frequent use, or internal failures within the switch mechanism that prevent it from signaling the motor to start.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryers.

This wiring harness connects the washer control board to console switches and sensors, restoring reliable electrical communication so the machine can receive user inputs and run cycles correctly. What it does

• Links the control board to door switch, cycle selectors, and other console components so commands register.
• Replaces damaged or frayed wiring that can cause intermittent operation or unresponsive controls.
• Helps stop electrical shorts, error codes, or failure-to-start symptoms related to broken control connections.
• Restores factory routing and connector fit for secure, vibration-resistant connections.

• One wiring harness as shown.

• Always unplug the washer or shut off power at the breaker before servicing.
• Match connector shapes and wire colors to OEM locations; avoid forcing connectors.
• Route harness along original clips and channels to prevent pinching or rubbing.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Fix a washer that won't advance through cycles or stays stuck on one setting. This mechanical timer restores proper cycle sequencing. 1-hour DIY repair.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

If your washer won't select the right water temperature or cycles are stuck on one setting, this temperature switch may need replacement.

Replacement timer knob for washer dryer combos. Mounts to the control timer shaft to select cycles and settings. Needed when original is cracked or stripped.

PPH ab st/z/ch `6 - 18x.60

Right endcap for washer dryer combo units. Covers and protects the right side panel edge. Replace if cracked, broken, or missing for a complete look.

Mounting screw secures panels, trim, or brackets in dryers, washers, and ranges. Replace lost, stripped, or corroded screws to restore stability.

Secures wiring harness to prevent chafing and maintain safe wire routing in washers, dryers, and laundry appliances. Replace if loose or broken. Check your model for compatibility.

Converts compatible gas dryers from natural gas to propane. Includes orifices and components for safe LP operation. Order if switching fuel types.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Secures the drain hose to prevent leaks and disconnection during spin cycles. Replace if cracked, loose, or causing water leakage. Verify fit with your model.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Vertical spring adjuster insert.

This is the manufacturer's installation instruction sheet for proper setup and initial use. It provides installer-facing steps and safety notes to help ensure the appliance is installed correctly and operates as intended. What it does:

• Gives step-by-step installation guidance and mounting/clearance requirements
• Lists basic safety warnings and required installation precautions
• Helps prevent installation errors that can cause performance issues or damage
• Advises on initial hookups (electrical, water, venting) in plain language

• Installation instruction sheet

• Read all instructions completely before starting installation
• Follow local codes and use qualified personnel for electrical/plumbing connections
• Keep this sheet with the appliance for future reference and for the owner
• If installation instructions conflict with local codes or the service manual, follow the code or service manual

This part has been discontinued by the manufacturer and is no longer available.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.