Parts for Whirlpool RF365BXPN1: 03 - Control Panel Parts

This flat washer is a small, precision metal spacer used with fasteners to secure components and distribute load, helping maintain proper alignment and prevent wear. It restores correct spacing and fastening where the original washer is missing or damaged. What it does:

• Provides a stable bearing surface for bolts and nuts to prevent loosening and abrasion
• Maintains proper spacing and alignment of adjacent components
• Helps reduce vibration and wear at fastened joints
• Resolves symptoms like loose panels, rattling near fasteners, or misaligned assemblies

• One flat washer, as shown

• Disconnect power to the appliance before beginning any repair
• Use the exact replacement washer size and thickness; do not substitute with a different type
• Tighten fasteners to secure but avoid over-tightening which can deform the washer or strip threads

Replacement mounting screw for securing panels, brackets, and components to your appliance chassis. Needed when original screws are stripped or missing.

10 - 16 x 1/2

This part has been discontinued and is no longer available.

This part has been discontinued and is no longer available.

This insulating part provides thermal protection for internal appliance components, helping reduce heat transfer and protect wiring and nearby parts from heat-related damage. It's a simple replacement to restore proper insulation where worn or missing. What it does:

• Shields nearby components from excessive heat and helps maintain safe operating temperatures
• Protects wiring, connectors, and plastic parts from heat exposure that can cause melting or failure
• Helps reduce heat transfer that can worsen component wear or trigger thermal faults
• Commonly replaced when insulation is torn, brittle, scorched, or missing

• One insulating part as shown

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Verify the part position and orientation before removal; take photos to aid reassembly
• Use basic hand tools; avoid compressing or damaging the insulating material during installation
• If you see heat damage to wires or other components, inspect and replace those parts as needed.

Replacement 8-18 thread screw for securing panels, brackets, and trim on appliances. Replace worn, stripped, or missing screws to keep components aligned.

Specs: 10-16 x 1/2 inch.

Loose or missing dishwasher door latch? This latch knob screw secures the knob to its shaft, restoring firm operation. Quick 5-minute fix.

Burner stuck on high or won't regulate temperature? This infinite switch controls top burner heat settings. Straightforward DIY fix, 15-30 minutes.

Burner stuck on high or won't heat properly? This surface element switch controls your range burner temperature. Simple 15-minute DIY fix.

Size: 6-32 x 9/32 inch.

Set includes 4 black burner knobs, 3 different selector knobs and 2 different thermostat knobs. This set fits many Whirlpool made ranges. Check by model number if not sure. Made by Whirlpool.

Set includes 4 black burner knobs, 3 different selector knobs and 2 different thermostat knobs. This set fits many Whirlpool made ranges. Check by model number if not sure. Made by Whirlpool.

This part has been discontinued by the manufacturer and is No Longer Available.

This replacement timer knob attaches to the control panel timer so you can set and adjust time reliably. Replacing a worn or missing knob restores a secure grip and clear pointer orientation for everyday use.

• Attaches to the timer shaft to turn and set the kitchen timer
• Common fix for knobs that are cracked, stripped, loose, or missing
• Helps when the timer can't be set or the shaft spins without turning
• Restores smooth rotation and proper alignment on the control panel

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft
• Align the new knob with the shaft and press firmly until fully seated
• Test timer operation and pointer alignment before restoring power

Set includes 4 black burner knobs, 3 different selector knobs and 2 different thermostat knobs. This set fits many Whirlpool made ranges. Check by model number if not sure. Made by Whirlpool.

The Clip is an OEM part for Whirlpool dryers. This part secures the control knob to the dryer’s control panel, ensuring it remains firmly attached and functions correctly. The clip helps provide stability and precise control over the dryer settings.

Causes of a bad clip can include regular wear and tear, accidental damage during use, or stress from frequent adjustments.

Symptoms of a bad clip include:

• Knob becoming loose or falling off
• Difficulty turning the knob to adjust settings
• Knob not staying securely in place
• Knob wobbling or feeling unstable

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.