Parts for Whirlpool RJE395PW0: 04 - Control Panel Parts

Specs: 10-16 x 1/2 inch.

10 - 16 x 1/2

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

Specs: 10-16 x 1/2 inch.

This selector switch knob replaces a worn or missing control knob on a range/oven. It restores a secure, easy-to-turn grip on the selector switch so you can confidently choose functions when the original knob is cracked, stripped, or missing.

• Attaches to the selector switch shaft so you can select oven functions, depending on model
• Direct replacement for knobs that are cracked, stripped, loose, or missing
• Restores proper feel and control when turning the selector switch
• Common symptoms: knob falls off, hard to turn, heat-damaged or worn knob

• Disconnect power to the appliance to prevent accidental activation
• Pull the old knob straight off the selector switch shaft
• Align the shaft orientation with the new knob and press firmly until fully seated
• Verify smooth rotation and correct alignment with the panel markings

This infinite switch controls the variable heat settings for a cooktop surface burner, restoring adjustable heating for smooth cooking. It replaces a failed control to help the burner reach and hold selected temperature levels. What it does

• Regulates power to a surface element so heat changes smoothly from low to high.
• Common symptom: burner won't heat or only works on one setting.
• Common symptom: heat level won't change or is stuck at a single setting.
• Can cause clicking or intermittent burner operation when failing.

• Disconnect power to the appliance at the breaker before servicing.
• Confirm terminal locations and wiring match your original switch; label wires before disconnecting.
• Access typically requires removing the cooktop or control panel.

This latch knob screw secures the latch knob to its shaft on compatible appliances. Replace a missing, stripped, or rusted screw to restore a firm, reliable attachment and proper latch/knob operation. What it does:

• Attaches the latch knob securely to the latch mechanism/shaft
• Helps maintain proper door latch engagement and knob control
• Common fix for a loose, wobbly, or falling-off knob
• Replaces a lost, corroded, or cross-threaded screw

• 1 latch knob screw

• Disconnect power and allow the appliance to cool completely before servicing
• Align the knob on the shaft and start the screw by hand to avoid cross-threading
• Tighten with the correct screwdriver; do not overtighten to prevent damage
• The latch engages and releases smoothly after installation

This part has been discontinued and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Size: 26 inches long. F18t8/cw/k26.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This spring-style tube clamp secures flexible tubing to fittings, helping prevent leaks and maintain proper flow. It's a simple replacement that restores a firm seal on water or drain lines. What it does:

• Keeps flexible tubing firmly clamped to barbed or nipple fittings
• Helps stop or reduce leaks from loose or corroded connections
• Prevents tubing from slipping off under pressure or vibration
• Useful where a compact, spring-action clamp is required

• Disconnect power and shut off water to the appliance before replacing parts
• Use pliers to expand the clamp, position it over the tube/fitting, then release to secure
• Inspect connected tubing and fittings for damage; replace if cracked or severely corroded

10 - 16 x 1/2