Parts for Kitchenaid KOST100ESS20: Control Panel Parts

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This is a replacement 8-18 screw used to secure components in compatible Whirlpool appliances. It provides a reliable, corrosion-resistant fastener to restore proper fit and function for panels and internal parts. What it does:

• Secures panels, brackets, or small internal components where an 8-18 thread is specified
• Restores loose or missing fasteners that cause rattling, misalignment, or improper sealing
• Matches OEM thread size and head profile for a correct fit when listed for your model
• Prevents further wear or damage caused by using the wrong screw size

• One screw as shown

• Turn off and unplug the appliance before starting any repair
• Use the proper screwdriver or driver bit to avoid stripping the head
• Do not overtighten—tighten until snug and components seat without play
• Replace only where the OEM specifies an 8-18 screw to ensure proper fit

This foam seal fits between mating parts to create a tight barrier that helps prevent leaks and rattling. Replacing a worn or missing seal restores proper sealing and helps keep your appliance running quietly. What it does:

• Creates a compliant gasket between components to limit air or moisture passage
• Helps dampen vibration and reduce rattling/buzzing where parts meet
• Helps maintain proper airflow or fluid routing as designed
• Typical symptoms include leaks, condensation/frost near a joint, or new vibration noises

• One foam seal

• Disconnect power; turn off the water supply before service
• Note the original seal's routing/orientation before removal
• Clean and dry all mating surfaces; remove old foam and residue
• Install without stretching or over-compressing; ensure even contact with no gaps

Color: Stainless

This wire harness is the electrical assembly that connects controls and components so your appliance can receive power and signals. Replacing a damaged harness restores reliable electrical connections and helps appliances operate safely. What it does:

• Carries power and control signals between the control board and components
• Can cause no-start, intermittent power, or unresponsive controls when damaged
• Restores proper component communication when cracked wires or corroded terminals are replaced
• Prevents shorting and electrical faults when routed and secured correctly

• Disconnect power (unplug or switch off breaker) before starting any repair
• Inspect connectors and routing; replace if terminals are corroded or insulation is damaged
• Avoid pinching or stretching wires; secure harness with original clips and ties

This wire harness is a direct-replacement electrical harness that restores factory wiring connections between the control and major components. Replacing a damaged harness helps stop intermittent power, control faults, and unsafe arcing. What it does:

• Carries power and signals between the appliance control and key components.
• Replaces damaged or frayed wiring that can cause intermittent operation or failure to start.
• Eliminates arcing, burnt connectors, or visible wire insulation damage that can create safety risks.
• Restores reliable connector fit and routing for proper component function.

• One replacement wire harness with factory-style connectors.

• Disconnect power (unplug or switch off breaker) before starting any work.
• Handle connectors by the housings; avoid pulling on wires to prevent damage.
• Route harness to match original routing and secure with existing clips or ties.

This mounting bracket is a replacement support bracket that secures appliance components and keeps assemblies aligned for reliable operation. It restores proper fit and helps prevent rattling or movement from loose fittings. What it does:

• Secures panels or assemblies to the appliance frame to maintain proper alignment
• Reduces vibration and rattling caused by loose or damaged supports
• Restores mounting points that prevent sagging or separation of connected parts
• Helps ensure stable operation after repairs involving removed or replaced hardware

• Follow the appliance service manual for exact location and fastener torque
• Disconnect power (and gas if applicable) before beginning any repair
• Use appropriate tools and replace any damaged screws or clips with OEM-equivalent fasteners