Parts for Whirlpool WFC310S0EB3: Control Panel Parts

Color: White  Note: Left side endcap

Black left side end cap panel for electric and gas ranges. Replaces cracked, broken, or damaged side trim pieces. Installs on left exterior edge.

Right side end cap panel for ranges in black. Replaces cracked, broken, or missing end panel. Covers and protects the exterior side of your range.

White plastic end cap that covers the right side panel edge of your range. Replaces cracked, broken, or missing endcaps to restore a finished appearance.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Buttons not responding or display blank on your electric range? The control panel manages all cooktop and oven functions. Moderate DIY repair.

This control panel is the user-facing console that houses the oven/range controls and display, restoring clear button access and readable status feedback. Replace a damaged or unresponsive console to regain normal control operation. What it does:

• Provides the touchpad/buttons and display used to set temperatures, timers, and modes.
• Sends user commands to the oven/range electronic control so selections start the appliance.
• Replaces a cracked, faded, or physically damaged panel to restore usable controls.
• Helps address symptoms like unresponsive buttons, unreadable display, or intermittent control behavior.

• Always disconnect power (unplug or switch off circuit breaker) before starting repair.
• Handle the display and electronic interfaces carefully; avoid bending or stressing the panel.
• Installation typically requires removing trim or console screws and transferring any mounting hardware or connectors.

The Infinite Control Switch is an OEM part for Whirlpool ranges and cooktops. This part allows for precise adjustment of the heat level, enabling users to achieve the perfect temperature for various cooking techniques, from simmering to boiling. 

Causes of a bad Infinite Control Switch can range from electrical issues, such as short circuits or worn contacts, to mechanical failures within the switch itself.  

Symptoms of a malfunctioning Infinite Control Switch include:

• Burners not heating to the set level or overheating
• Inability to adjust the burner temperature
• Burners not turning on or off when the control switch is operated

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Burner stuck on high or won't heat properly? This surface element switch controls your range burner temperature. Simple 15-minute DIY fix.

Replace your range's surface unit indicator light when it stays on, flickers, or burns out. Signals when burners are hot for safety. Verify fit.

If your range doesn't respond to buttons or knobs, the control board may have failed. This component coordinates all baking and broiling functions.

This electronic control board is the brain of the appliance, directing cycles and powering key components. Replacing a failed board helps restore proper operation, reliable starts, and accurate cycle sequencing. What it does:

• Coordinates inputs from sensors and the user interface to control programmed functions
• Sends power to motors, pumps, fans, valves, and heaters as needed
• Manages cycle timing and safety checks
• Common symptoms include: won't power on or start, won't advance/complete, stops mid-cycle, erratic operation, or error codes

• 1 electronic control board

• Disconnect power at the breaker or unplug before servicing
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time from the old board to the new board; each is fully seated
• Secure the board in its housing/bracket, reassemble, and run a test/diagnostic cycle if available

Secures the control console assembly to your range, keeping the control board and interface stable. Replace if bracket is cracked, broken, or missing.

Protective cover that conceals your range's control box and wiring. Replaces cracked, broken, or missing covers to restore a finished look.

This machine screw is used across appliances to secure brackets, covers, and internal components. Replacing a missing or stripped fastener helps keep parts aligned and tight, reducing vibration and preventing loose or shifting assemblies.

• Provides machine-thread fastening for panels, brackets, and internal parts
• Helps eliminate rattling, vibration, and loose fits
• Restores proper attachment when the original screw is stripped, missing, or corroded
• Used wherever an 8-32 screw is specified in the service manual or parts list

• Disconnect power to the appliance; turn off gas/water if applicable
• Match the screw to the original location to confirm size and thread
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten to prevent stripping or cracking

Secures wiring and components to prevent movement and disconnection in your electric range. Replace if clips are broken or wires are loose. Verify fit with your model number.

Replace your range's surface burner control knob if cracked, stripped, or missing. Attaches to the valve shaft to control heat settings on your cooktop.

Replace a broken, cracked, or missing control knob on your electric range. Restores clean appearance and smooth operation of burner settings.

Broken indicator light lens? This red lens covers the control panel light opening, restoring visibility and protection. Easy DIY fix in under an hour.

Secures range components and panels to maintain proper alignment. Replace if your original bracket is cracked, broken, or missing to restore stability.

Heat shield for electric ranges. Protects components from heat damage. Replace if cracked, warped, or missing to restore proper heat protection.