Parts for Lg LRGL5823D/00: Controller Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Insulator for electric and gas ranges. Installs between internal components to provide heat or electrical protection. Replace if cracked or missing.

Replacement screw secures panels and components in your microwave. Install when original hardware is stripped, rusted, or missing to stop rattles.

Secures interior panels and components. Replace when stripped, corroded, or missing to stop rattles and secure loose trim. Verify fit with your model number.

Fix intermittent power issues or non-working features with this range wiring harness. Restores reliable connections between electrical components.

Range controls not responding or functions intermittent? This wire harness restores electrical connections between components. Moderate DIY repair for most models.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

Replacement washer that secures fasteners and distributes load at connection points in ranges and ovens. Needed when original is missing, worn, or damaged.

Secures panels, brackets, and internal components in your range. Replace this screw if the original is missing, stripped, or rusted for proper fit.

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

Secures panels, brackets, and trim on your gas range. Replace this self-tapping fastener if it's missing, stripped, or damaged to restore alignment.

The Screw is an OEM component specifically designed for LG ranges. It plays an important mounting and fastening role by securely attaching internal components together.

The screws utilized within the range cabinet ensure sturdy construction and reliable mechanical cohesion. They allow for simple assembly and proper alignment of inner parts. 

Causes of bad screws can include wear and tear over time, or damage from overtightening leading to stripped threads or heads.

Symptoms of bad screws include:

• Loose, detached, or misaligned inner parts  
• Hardware that does not fit or interface as designed
• Unintended noises or movement during the operation

This OEM LG replacement part is also compatible with Sears/Kenmore and some GE ranges utilizing similar fasteners. Replacement ensures the range remains mechanically sound.
 

This 4.0x16mm tapping screw secures trim, panels, and brackets on ranges and microwaves. Replace missing, stripped, or damaged screws during repair.

Factory-style screw for securing panels, brackets, and assemblies on gas ranges and cooktops. Replace if missing, stripped, or damaged during repairs.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

Adjustable metal leveling foot that elevates and stabilizes your range. Mounts to the bottom of the unit. Replace if broken, worn, or missing.

Replaces cracked or dented outer door trim to restore your range's appearance and seal support. Replace when damaged to maintain proper door sealing. Confirm fit.

Replacement handle for your range oven door. Installs on the front exterior of the door for opening and closing. Order if your original is cracked or broken.

This door sub-assembly replaces a damaged or worn outer door component to restore proper sealing and appearance. It provides the structural outer panel and mounting points needed for normal door operation and alignment. What it does:

• Replaces the refrigerator/freezer door outer assembly to restore fit and finish
• Provides proper mounting surfaces for hinges, handles, and trim pieces
• Helps the door close and seal correctly to maintain internal temperatures
• Addresses visible damage like dents, cracks, or distorted mounting holes

• Disconnect power and empty the door of contents before starting
• Retain all original fasteners and brackets if they are undamaged; replace any stripped hardware
• Verify hinge alignment and door clearance during reassembly to ensure proper sealing

Replacement window glass for range oven doors. Restores clear viewing area when original glass is cracked, chipped, cloudy, or shattered. Installs inside door.

Replace your range oven door hinge assembly when the door sags, binds, or won't close properly. Restores alignment and smooth operation. Verify fit with your model.

Support bracket for range oven door window glass. Secures and stabilizes the inner window panel. Replace if cracked, broken, or missing to restore door.

Safety cover for electric and gas ranges. Installs over internal components to protect wiring and mechanisms. Replace if cracked, broken, or missing.

This is the main electronic control board that manages the core functions of the refrigerator, including compressor operation, temperature regulation, and defrost cycles. It acts as the central processing unit that coordinates communication between sensors, motors, and user controls. Replace this board if the refrigerator stops cooling, displays error codes, or exhibits erratic behavior such as inconsistent temperatures or unresponsive controls.

The PCB Assembly is an OEM part for LG refrigerators. It stands for Printed Circuit Board, which is the main control board that manages and regulates various functions and components within the refrigerator.

Symptoms of a bad PCB Assembly include:

• The refrigerator not powering on or displaying any lights/indicators
• Specific components or features not functioning correctly (ice maker, dispenser, cooling, etc.)
• Error codes or warning lights illuminated on the control panel
• Strange noises or abnormal behavior from the refrigerator

Causes of a bad PCB Assembly can be related to electrical faults, such as short circuits, power surges, or component failures. Physical damage from impact, moisture exposure, or overheating can also contribute to the malfunction of the PCB.

This OEM LG part is also compatible with Sears/Kenmore refrigerators. 

This is a circular wire harness holder that secures and organizes internal wiring within the range. It clips onto the frame or mounting points to keep wires routed properly and away from heat sources. Replace this part if it is broken or missing, which can cause loose wiring or potential contact with hot surfaces.

Replace a damaged motor cover causing excessive noise or debris buildup. This housing shields the motor assembly and maintains proper airflow. DIY-friendly.

This part is the base for the small simmer burner on gas cooktops. It supports the burner cap and channels gas to the flame ports to promote consistent ignition and an even, stable flame. What it does

• Serves as the burner base for the auxiliary/simmer position
• Aligns and supports the burner cap for even flame distribution
• Routes gas from the orifice to the burner ports
• Common symptoms include weak or uneven flames, difficulty lighting with a known-good spark, or a cap that won't sit flat

• One auxiliary burner holder

• Disconnect power and shut off the gas supply before servicing
• Remove the grate and burner cap; take out mounting screws and lift off the old holder
• Transfer/reuse the orifice, igniter electrode, gasket, and hardware as applicable; seat the new holder evenly and tighten fasteners without over-torquing
• Restore gas and power; verify proper ignition and flame

Replace your range motor cover if the motor assembly is exposed or damaged. This protective housing shields internal components from dust and debris.

Note: Due to factory variations, please check your original board before ordering. This display control board has 17 buttons on the front. If your original board has 18 buttons, you may need part# EBR89296404 instead.

The Display PCB Assembly is an OEM part for LG ranges and stoves. It is the main circuit board that controls the display panel and oven. This assembly is responsible for operating all electronic functions such as temperature controls, timers, buttons and digital displays.

Causes of a bad display PCB assembly can be water or liquid damage, failure due to surges or spikes in the power supply over time, or due to normal component degradation after heavy use.

Symptoms of a bad display PCB assembly include:

• Faulty or unresponsive control buttons
• Erratic temperature control functions
• Glitches or failures in the digital display
• Inability to operate certain cooking modes

This OEM LG part is also compatible with some Kenmore models.

Replace your cracked, warped, or missing range oven rack. Installs inside the oven cavity to support cookware during baking, roasting, and broiling.

Fix rattling or misaligned range components with this fixing holder bracket. Secures internal parts to restore proper positioning and quiet operation.

If your gas range buttons don't respond or selectors fail, this control switch assembly restores reliable operation. Mounts in the control panel area.

This is a cast iron or porcelain-coated burner grate that sits on top of the range surface over a gas burner, providing a stable platform for cookware. It supports pots and pans above the flame for even heating. Replace this grate if it is cracked, chipped, warped, or if its finish has deteriorated to the point where cookware no longer sits level.

This is a center burner grate that sits on the cooktop surface and supports pots and pans over the burner. It provides a stable, elevated cooking surface to allow proper heat circulation. Replace this grate if it is cracked, warped, has broken supports, or its finish has deteriorated to the point where cookware no longer sits level.

Controls gas flow to your range burner. Replace this valve assembly when the original is faulty, leaking, or damaged to restore safe gas regulation.

If your range burners won't light or heat unevenly, the gas valve assembly may have failed. This part regulates gas flow to restore proper ignition.

Gas range won't ignite or heat properly? This valve assembly controls gas flow to your oven and burners. Restores ignition and safe operation.

The Burner Head is an OEM part for LG gas ranges. It is located underneath the burner caps and is responsible for producing the ignited flame during cooking. 

Symptoms of a bad burner head include: 

• Difficulty lighting or sustaining a flame
• Unbalanced or irregular burner performance  
• Yellow flame tips or soot buildup
• Burner tubes appearing warped or misshapen

Causes of a faulty burner head can be issues like cracks in the burner material, blockages within the gas tubes, or deformations from long-term heat exposure.

 This burner head is also compatible with select Sears/Kenmore gas range models.

Replace your gas range burner head if flames are uneven, won't ignite, or produce yellow/orange flames. Controls ignition and flame for each burner.

Replace a gas range burner head with uneven flames, weak heat output, or clogged ports. Sits at the center of the burner unit to control flame pattern.

Fix uneven flames or poor heat distribution with a new burner cap. Covers the burner head to ensure proper gas flow and heat transfer on your cooktop.

Fix uneven flames or yellow burner tips with this gas range burner cap. Spreads flame evenly across the burner surface. Simple 5-minute swap.

Replace a burner cap when flames are uneven, yellow, or won't stay lit. This cap distributes heat evenly across your cooktop. Simple 5-minute swap—no tools.

Burner cap sits over sealed burner units to direct flame upward. Replace if cracked, chipped, or damaged from wear. Lifts off easily for quick replacement.

If your gas burner flame is uneven or yellow, the burner cap may be warped or cracked. This component covers flame ports for proper heat distribution.

Fix intermittent power or control failures with this gas range cable assembly. Routes power between the control board and components to restore operation.

This rigid molded pipe assembly routes water or drainage inside the appliance to ensure proper flow and prevent leaks. Replace a cracked, clogged, or damaged tube to restore reliable water movement and reduce leaks. What it does:

• Channels water or condensate between internal components for normal operation
• Prevents leaks caused by cracked or split tubing
• Helps restore normal filling, dispensing, or draining when the original pipe is blocked or broken
• Fits where a single molded or formed pipe is required to maintain proper routing

• One rigid molded pipe assembly

• Disconnect power and shut off water supply before beginning repairs
• Inspect surrounding fittings and seals; replace any damaged clamps or gaskets
• Securely fasten both ends and check for leaks after reconnecting water

Replacement gas supply pipe for gas range burners. Connects gas valve to burner assembly. Order if your original pipe is damaged, corroded, or missing.

The Switch is an OEM part for LG ovens. This switch is responsible for turning the oven light on and off when the door is opened and closed. It ensures that the oven light operates correctly, providing visibility inside the oven cavity when the door is opened.

A bad oven door light switch can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as the oven light not turning on or off when the door is opened or closed, it may be time to replace the light switch.

Symptoms of a bad switch include:

• Oven light not turning on when the door is opened
• Oven light not turning off when the door is closed

Ensure proper function in your LG oven by replacing the faulty switch with this genuine OEM part.

This LG replacement part is also compatible with select Kenmore models.
 

This genuine replacement power cord assembly restores electrical power to the appliance by replacing a damaged or worn main power cable. It provides a direct, factory-fit connection for safe, reliable operation. What it does

• Delivers mains power from the wall outlet to the appliance's internal wiring and control systems.
• Replaces frayed, cut, melted or otherwise damaged cords that can cause loss of power or intermittent operation.
• Helps eliminate burning smells, visible damage, or exposed wires that indicate a compromised power connection.
• Restores a secure plug and strain-relief connection to reduce stress on terminal connections.

• One power cord assembly.

• Always disconnect power at the breaker or unplug the appliance before starting any work.
• Verify correct cord routing and secure the strain relief/retainer to prevent pinching or chafing.
• Tighten terminal screws to the manufacturer's specification and ensure proper grounding.

This AC fan motor powers the convection fan inside the oven cavity, circulating hot air for even cooking and baking. It mounts behind the rear panel of the oven and drives the fan blade that distributes heat throughout the compartment. Replace this motor if the oven heats unevenly, the convection fan is not spinning, or you hear unusual noises coming from the back of the oven during convection cooking.

Fix intermittent operation or power loss in your gas range. This wire harness restores reliable electrical connections between components.

Replace your range's wire harness if the existing wiring is damaged, frayed, or showing signs of wear. Connects electrical components inside your range.

If your oven won't reach the right temperature or shows an F9 error, the temperature sensor may be faulty. Simple DIY repair in under 45 minutes.

Replace a damaged or corroded wire harness in your range. This single-connection harness restores proper electrical connections when original wiring is frayed, melted, or broken.

Secures the control panel to your range cabinet. Replace if the bracket is cracked, bent, stripped, or hardware no longer holds the console firmly in place.

Fixes uneven baking and noisy oven operation. This convection fan assembly circulates hot air for consistent cooking. Moderate DIY repair restores airflow.

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

Insulator for gas range burners. Installs beneath burner components to provide heat protection. Replace if cracked, broken, or missing for proper operation.

Replace your damaged or broken range handle bar. This bar installs on the oven door, providing a secure grip for opening and closing. Order now.

Motor loose or vibrating excessively? This motor bracket secures the motor to the chassis, reducing vibration and maintaining alignment for quieter operation.

Halogen oven light bulb illuminates your range interior for monitoring food while cooking. Replace when bulb burns out or flickers. Verify fit with your model.

This hinge bracket secures the oven door hinge mechanism on your range. Replace if the bracket is cracked, broken, bent, or missing to restore door support.

Seals your range door to maintain stable temperatures and prevent air leaks. Replace when worn, cracked, or no longer creating an airtight seal.

Seals your range oven door to prevent heat loss and maintain even cooking. Replace if worn, cracked, or causing temperature issues. Confirm fit with your model.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

This is a replacement pipe used to route fluid inside the appliance, restoring proper flow and preventing leaks. It's a direct-fit service part that replaces a damaged or worn tubing section for reliable operation. What it does:

• Directs water flow between components to maintain normal dispensing and circulation.
• Replaces cracked, split, or corroded tubing that can cause leaks or pooling.
• Helps stop intermittent or continuous drips and wet spots under or behind the appliance.
• Restores sealed connections when paired with proper clamps or fittings.

• One replacement pipe

• Disconnect power and shut off the water supply before beginning any repair.
• Handle carefully to avoid kinking; inspect and replace any worn clamps or seals.
• Use appropriate tools and follow the OEM parts diagram for routing and connection points.

Gas pipe that connects the gas supply to the burner assembly in your gas range. Replace if the pipe is cracked, corroded, or leaking to restore safe operation.

This pipe routes water inside the appliance to supply the dispenser and ice-making components, restoring reliable water flow and helping prevent leaks from damaged or clogged tubing. It's a direct-fit replacement designed to match OEM routing. What it does:

• Channels water from the inlet to the ice maker/dispenser assembly.
• Maintains correct internal water flow for ice production and dispensing.
• Replaces cracked, pinched, or corroded tubing that can cause leaks.
• Helps stop intermittent or reduced water flow caused by damaged piping.

• Disconnect power and shut off the water supply before starting.
• Inspect and, if needed, replace any adjacent clamps, gaskets, or fittings to ensure a leak-free seal.
• Re-route tubing to match original OEM path; avoid kinks or sharp bends.
• After installation, restore water and power, then check all connections for leaks while running a water/ice cycle.

Burner nozzle holder for gas ranges. Secures the gas nozzle in place on the burner assembly. Replace if cracked, broken, or missing to restore proper fit.

Fix inadequate or uneven broiling in your gas range with this broil burner orifice holder assembly. Restores proper heat distribution for cooking.

Fixes weak or uneven flames on gas range burners. This burner nozzle regulates gas flow for proper flame height. Simple DIY fix, takes 15 minutes.

The Burner Assembly is an OEM component specifically designed for LG gas ranges equipped with sealed cooktop burners. This integral assembly contains the ignition electrode, valve stem, and cast burner head to conduct flame across grates.  

Symptoms of a bad burner assembly include:

• Inability to ignite or maintain consistent flames under cookware
• Yellow broken or excessive flame instead of steady blue  
• Clicking ignition sounds but no combustion takes place
• Deteriorated valve stems limiting gas flow regulation

Causes of failure involve clogged ports blocking gas dispersion, cracked burner bases no longer supplying sufficient air intake, or damaged ignition systems disabling piezo sparks over dozens of heating cycles.

Replace yours today with this genuine OEM LG assembly to restore optimal cooktop performance. Factory-sealed construction withstands daily use maintaining even heat across pans and preventing gas leaks. Compatible with GE, Frigidaire, and Kenmore sealed burner models as a direct unit replacement.

Fix a burner that won't light or heat unevenly with this gas range burner assembly. Common repair for weak or inconsistent flames on cooktop surfaces.

Fix weak or uneven flames with this gas range burner assembly. Complete replacement component restores proper ignition and heating performance.

Replace your worn gas range burner assembly to restore reliable heating and proper ignition. Direct-fit replacement for damaged cooktop burners. Confirm fit with your model number before ordering.

Fix a gas range burner that won't light, has weak flames, or uneven heating. This burner assembly restores proper flame distribution. Moderate DIY repair.

Fix a gas range burner that won't light or has weak flames with this burner assembly. Moderate DIY repair typically completed in under an hour.

If your gas range burner won't light or has uneven flames, this burner assembly restores proper heating. Direct replacement part with moderate difficulty.

This heater cover mounts over the dishwasher's heating element at the bottom of the tub. It shields the element and helps direct wash water, protecting dishes and the tub floor from direct contact with the heater. What it does:

• Covers and protects the exposed heating element at the tub base
• Helps channel water flow around the element during the cycle
• Replace if the cover is cracked, warped/melted, or missing
• Can help prevent utensils or items from snagging near the heater area

• 1 heater cover

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and, if needed, the lower spray arm and filters to access the heater area
• Release retaining tabs or screws, remove the old cover, and seat the new cover evenly
• Ensure the cover locks securely and the spray arm spins freely before restoring service

Pressure regulator assembly for gas ranges. Mounts to the gas supply line to control fuel pressure. Replace if cracked, leaking, or damaged.

This is a metal base panel that sits at the bottom of the upper oven cavity in a range. It serves as a heat shield and floor surface, protecting the lower cabinet structure from direct heat exposure while helping distribute heat evenly. Replace this panel if it is warped, rusted, or has holes that allow grease and food debris to fall into the lower compartment.

Fix a burner that won't ignite or heat evenly with this surface burner assembly. Restores consistent flame and reliable heat to your gas range cooktop.

Reduces operational noise in your range. Replace if you notice increased rattling or vibration sounds. Verify compatibility with your model number.

Fixing frame that secures internal components in your range. Replace if your original frame is bent, cracked, or broken to properly mount parts inside the unit.

Outer front panel that restores your range's appearance. Replaces cracked, dented, or discolored original panel. Installs on the front exterior.

Rubber foot pad that supports and stabilizes your range on the floor. Replace if cracked, broken, worn, or missing to keep your appliance level.

This is a metal anti-tip bracket that secures the range to the floor or wall to prevent it from tipping forward. It is a critical safety device, especially when heavy items are placed on an open oven door. Replace or install this bracket if yours is missing, damaged, or if you are repositioning the range after a move or kitchen remodel.

Storage drawer for electric and gas ranges. Installs at the bottom of your range for kitchen utensil storage. Replace if cracked, broken, or missing.

Range storage drawer rail guide directs adjustable drawer movement in and out of position. Replace if clips are broken, warped from heat, or damaged.

Fix an oven that won't heat or gives F9 error code. This gas valve regulates gas flow to burners. Moderate DIY repair requiring basic tools.

Mounting anchor for range door handles. Replaces worn, broken, or missing anchors to restore secure handle attachment and eliminate wobbling or loose fit.

Converts your gas range between natural gas and LP propane fuel sources. Includes orifices and components needed for safe fuel type conversion.