Parts for Lg LRGL5825F/00: Controller Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This replacement screw fastens panels and components in your appliance, keeping them secure and aligned. Replace stripped, rusted, or missing hardware to stop rattles and ensure assemblies stay tight through everyday use.

• Secures covers, brackets, and internal assemblies at the specified mounting points
• Helps correct looseness or misalignment after a fastener is lost or stripped
• Can reduce rattling or vibration noises caused by loose fasteners
• Restores proper fit of panels or trim pieces

• Disconnect power to the appliance and shut off water or gas before servicing
• Match length and thread to the original fastener before installation
• Start threads by hand to avoid cross-threading; tighten only until snug to prevent damage
• Reuse any washers, spacers, or threadlocker originally installed at this location

This truss head tapping screw secures interior panels and small components on compatible appliances, restoring proper fit and stopping rattles or loose trim. It's a direct hardware replacement for a single mounting point. What it does:

• Fastens panels, brackets, and trim where a low-profile truss head is required
• Replaces missing or stripped screws that cause rattling or loose parts
• Provides a secure hold by forming threads in sheet metal during installation
• Useful for repairing cosmetic or functional panel alignment issues

• Disconnect power before working on any appliance to avoid shock or injury
• Use the correct sized Phillips or Torx driver to prevent cam-out or screw damage
• Start straight and thread slowly; do not overtighten to avoid stripping sheet metal
• Replace only with the exact part number for best fit and performance

This single wiring harness connects electrical components to restore reliable power and signal routing in compatible appliances. It replaces a damaged or frayed harness to help eliminate intermittent connections and wiring-related failures. What it does

• Provides the factory-style set of wires and connectors to link control and power components.
• Restores secure electrical connections that can cause appliances to not start, lose power, or operate intermittently.
• Replaces worn, melted, or damaged wiring that create shorts or unreliable performance.
• Maintains OEM routing and connector fit to ensure proper interface with existing components.

• One single wiring harness as shown.

• Disconnect the appliance from power (and water if applicable) before servicing.
• Match connectors and wire colors; do not force connectors—verify seating and latch engagement.
• Route the harness along the original clips and channels; avoid contact with hot components or sharp edges.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This customized washer is a small hardware piece that secures fasteners and helps distribute load where screws or bolts attach to appliance components. It restores proper fit and reduces movement at the connection point. What it does:

• Provides a stable bearing surface for screws or bolts to prevent pull-through and material damage
• Helps keep fasteners tight and reduces vibration-related loosening or rattling
• Maintains correct spacing and alignment of panels or internal parts
• Can help form a seal on fasteners in locations prone to vibration or minor movement

• Disconnect power and water (if applicable) before servicing the appliance
• Retain or replace the associated fastener; small parts can be easily lost—work on a clean surface

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This tapping screw secures appliance panels, brackets, and trim. Replace a missing or stripped fastener to restore a tight, rattle-free fit and keep components properly aligned.

• Cuts its own threads as it drives (self-tapping) to fasten metal or plastic components securely
• Helps eliminate looseness and vibration noises when an original screw is missing or damaged
• Typical signs you need this part: loose or rattling panels, gaps/misalignment, or covers that won't stay secured
• Direct replacement for the original fastener in the same location

• Disconnect power; turn off water or gas supplies before service
• Start the screw by hand to avoid cross-threading, then tighten with the correct driver
• Align parts fully before tightening and avoid overtightening, especially into plastic
• Reuse any original washers or clips that were installed with the screw

The Screw is an OEM component specifically designed for LG ranges. It plays an important mounting and fastening role by securely attaching internal components together.

The screws utilized within the range cabinet ensure sturdy construction and reliable mechanical cohesion. They allow for simple assembly and proper alignment of inner parts. 

Causes of bad screws can include wear and tear over time, or damage from overtightening leading to stripped threads or heads.

Symptoms of bad screws include:

• Loose, detached, or misaligned inner parts  
• Hardware that does not fit or interface as designed
• Unintended noises or movement during the operation

This OEM LG replacement part is also compatible with Sears/Kenmore and some GE ranges utilizing similar fasteners. Replacement ensures the range remains mechanically sound.
 

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

The Range Foot is an OEM replacement part for LG electric ranges. This adjustable metal foot elevates and stabilizes the large appliance above the counter level.

Symptoms of a faulty or damaged foot include:

• Wobbling or uneven stability of the range top  
• excessive stress on internal components from improper elevation
• Possible scratches or damage to surrounding countertop surfaces

Causes typically relate to normal scratches and denting accumulated from years of transportation and positioning the heavy appliance. Constant weight exposure can deform adjustable parts.

This outer door frame replaces a cracked, dented or worn door trim to restore the door's appearance and support for the door seal. It gives the door a solid, finished edge and helps maintain proper sealing. What it does

• Replaces damaged or warped outer door trim that can let moisture or air into the cabinet
• Restores proper alignment and mounting for the door gasket and inner door components
• Improves door appearance by covering dents, scratches or missing trim
• Helps reduce drafts or condensation caused by a damaged door edge

• One outer door frame

• Disconnect power and empty the door before starting; work on a stable surface
• Remove door hardware and inner trim panels as required to access the frame
• Handle glass and trim carefully to avoid scratching; use correct fasteners and torque evenly

This genuine OEM door handle replaces a broken or worn handle to restore safe, reliable door opening and a finished appearance. Fits the original mounting locations and matches the appliance's factory look. What it does:

• Provides a secure grip for opening and closing the appliance door
• Replaces cracked, chipped, loose or missing handles
• Restores proper leverage to prevent stress on door latches and hinges
• Matches the factory fit and finish for a clean appearance

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the handle to prevent damage
• Use the original or manufacturer-specified screws and hardware; tighten securely but avoid over-torquing
• If the handle attaches behind trim or a panel, remove the trim carefully to avoid clips or fastener damage

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

This is a replacement door sub-assembly that restores the appliance door's structure and proper closing action for safe, reliable operation. Use it to replace a damaged, bent, or non-sealing door component. What it does

• Replaces the door sub-assembly that secures the door frame and related components
• Restores proper door alignment and closing action to improve sealing and operation
• Helps stop issues like poor door fit, rattling, or difficulty latching
• Works as a direct-fit replacement when the original sub-assembly is worn or damaged

• Disconnect power and water before starting any repair
• Handle any glass or trim carefully to avoid breakage or injury
• Basic hand tools typically required; refer to the appliance service manual for specific fastener locations and torque

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

This hinge assembly secures and guides a refrigerator/freezer door, restoring proper alignment and smooth opening/closing for a tight seal and reliable operation. Use when door sags, binds, or fails to close fully. What it does:

• Supports the door and keeps it aligned on its track for even sealing
• Allows smooth pivoting so the door opens and closes properly
• Reduces sagging or misalignment that can cause gaps or rubbing
• Helps stop door noise caused by worn or damaged hinge components

• Disconnect power to the appliance before servicing and work with the door supported to prevent injury or damage
• Handle the hinge and door carefully; use appropriate tools and get assistance if the door is heavy
• Confirm hinge orientation (left/right/top/bottom) and fastener types before installation
• Replace missing or worn mounting hardware or shims with OEM-specified parts for proper fit

This main control board is the appliance's central electronic controller. It manages power and timing to key components, helping restore proper operation when the original board is faulty, damaged, or no longer responding.

• Coordinates appliance functions based on user selections and sensor feedback
• Switches power to loads such as motors, fans, valves, heaters, and lights
• Manages cycle timing, safety interlocks, and system monitoring
• Failure symptoms include no power, unresponsive controls, failure to start or run, intermittent operation, or error codes

• Disconnect power before servicing; verify all capacitors have discharged
• Use ESD protection and handle the board by its edges
• Photograph and label connectors; transfer wiring one at a time to the new board
• Follow the service manual for any model-specific checks or option/program settings after installation

The PCB Assembly is an OEM part for LG refrigerators. It stands for Printed Circuit Board, which is the main control board that manages and regulates various functions and components within the refrigerator.

Symptoms of a bad PCB Assembly include:

• The refrigerator not powering on or displaying any lights/indicators
• Specific components or features not functioning correctly (ice maker, dispenser, cooling, etc.)
• Error codes or warning lights illuminated on the control panel
• Strange noises or abnormal behavior from the refrigerator

Causes of a bad PCB Assembly can be related to electrical faults, such as short circuits, power surges, or component failures. Physical damage from impact, moisture exposure, or overheating can also contribute to the malfunction of the PCB.

This OEM LG part is also compatible with Sears/Kenmore refrigerators. 

This control knob assembly replaces a worn, cracked, or missing range/stove control knob to restore reliable selection of heat and function settings. It provides a solid grip and tactile feedback for accurate adjustments. What it does:

• Replaces damaged or loose control knob for easy temperature and function selection
• Restores positive detent feel so settings stay where you set them
• Prevents slipping or spinning that can cause incorrect cycles or temperatures
• Fits the original control shaft for correct alignment and operation

• Knob assembly

• Disconnect power to the appliance before starting any repair
• Pull the old knob straight off the control shaft; align and push the new knob fully onto the shaft
• If the knob is stiff, inspect the shaft for debris or damage before forcing it on
• Use basic hand tools only;

This motor cover is the replacement housing that protects the motor assembly and nearby components, helping keep debris and moisture out while supporting correct airflow and quiet operation. Fits the OEM motor location to restore safe serviceability. What it does:

• Shields the motor from lint, dust and foreign debris that can cause overheating or premature wear
• Helps direct airflow around the motor for proper cooling
• Reduces vibration and rattling by securing motor components in place
• Can address symptoms such as unusual motor noise, rubbing sounds, or visible debris near the motor

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the appropriate access panel(s) and fasteners; keep track of screws and clips
• Align cover over the motor housing and fasten securely without overtightening

This part is the base for the small simmer burner on gas cooktops. It supports the burner cap and channels gas to the flame ports to promote consistent ignition and an even, stable flame. What it does

• Serves as the burner base for the auxiliary/simmer position
• Aligns and supports the burner cap for even flame distribution
• Routes gas from the orifice to the burner ports
• Common symptoms include weak or uneven flames, difficulty lighting with a known-good spark, or a cap that won't sit flat

• One auxiliary burner holder

• Disconnect power and shut off the gas supply before servicing
• Remove the grate and burner cap; take out mounting screws and lift off the old holder
• Transfer/reuse the orifice, igniter electrode, gasket, and hardware as applicable; seat the new holder evenly and tighten fasteners without over-torquing
• Restore gas and power; verify proper ignition and flame

This motor cover protects the appliance motor assembly and helps keep moving parts free from dust and debris for reliable operation. It restores the motor's protective housing after repair or replacement. What it does:

• Shields the motor and internal components from dust, lint, and light impact
• Helps maintain proper airflow around the motor to support cooling
• Reduces risk of accidental contact with moving parts for safer operation
• Restores original fit and alignment of motor mounting points

• One motor cover

• Disconnect power before beginning any repair to avoid shock or injury
• Remove outer panels and mounting hardware to access the motor area; retain fasteners for reassembly
• Confirm correct orientation and seating over the motor before securing screws
• Replace any damaged mounting tabs or fasteners to ensure a secure fit

The Rack is an OEM component designed specifically for LG ranges. This rack provides a surface for baking, roasting, and broiling different types of food inside the oven cavity. 

The rack is responsible for safely supporting food during the cooking process. It is constructed of durable steel with a non-stick-coated surface for easy cleaning.

Causes of a bad rack can include wear and tear over time from repeated exposure to high oven temperatures. This can cause the steel to weaken or the non-stick coating to peel. Heavy pans left on the rack may also cause dents or bends in the surface. 

Symptoms of a bad rack include:

• Sagging or uneven rack that does not lay flat 
• Warped or bent wires that no longer securely hold pans   
• Chipped or peeling non-stick coating

This OEM LG part is also compatible with Sears/Kenmore ranges. 

This fixing holder secures an internal appliance component to reduce movement and restore proper alignment. It's a small replacement bracket that helps stop rattling and keeps parts positioned for reliable operation. What it does:

• Provides a secure mounting point for the associated internal component or assembly
• Prevents movement, reducing noise, vibration, and abnormal contact
• Helps restore correct part alignment that can cause poor function when loose or broken
• Commonly replaces cracked, bent, or missing holders that allow shifting or rattling

• One holder as shown

• Disconnect power before servicing and follow all safety guidelines
• Basic hand tools typically required; remove covers or panels for access
• Inspect surrounding clips, screws, and mounts and replace any worn fasteners

This control panel is the user interface assembly for your appliance, providing the touchpad buttons and display needed to select cycles and see status. Replaces a worn or unresponsive front control module to restore normal panel operation. What it does:

• Houses the membrane/touchpad and display used to enter settings and show cycle information.
• Restores button responsiveness when keys are worn, unresponsive, or intermittently working.
• Returns on-screen status and numeric/LED feedback when the display is dim, blank, or unreadable.
• Helps resolve control-related errors caused by a damaged or non-functioning front panel assembly.

• One control panel (touchpad/display) assembly.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle the display and ribbon/connector gently to avoid damage; inspect connectors for bent pins.
• Some models require removing the outer trim or control housing—keep screws and small parts organized.

This switch assembly replaces a worn or failed control switch to restore reliable button or selector operation and return normal control response. It mounts in the appliance's control area and connects to the main harness. What it does

• Acts as the user-operated electrical switch that sends signals to the appliance control board
• Replaces a switch that causes unresponsive buttons or selector knobs
• Fixes intermittent operation or functions that only work when the control is pressed firmly
• Helps restore consistent on/off or cycle-selection behavior

• Disconnect power (unplug or switch off breaker) before starting any work
• Handle connectors gently; unplug the harness by the plug, not the wires
• Small hand tools are typically required; follow OEM disassembly steps for access

The Grille Assembly is an OEM part for LG gas ranges. It protects burner components while allowing heat to radiate from the cooktop. This heavy-duty assembly features precisely centered cutouts aligned with each gas burner.

Causes of a bad grille assembly can include warping, cracks or breaks from heat exposure over time. Accidental damage from pans or cookware may also impact integrity.

Symptoms of a dysfunctional grille assembly include:

• Misaligned or loose-fitting range of burner flames
• Excessive dirt or grease accumulated below the assembly
• Ability for small objects to fall into burner wells
• Damage, corrosion or breakage of individual grates

This LG part is also compatible with some Kenmore models.

This grille assembly restores the front lower trim and vent cover on compatible refrigerators, protecting internal components and improving appearance. It replaces cracked, broken, or missing grilles to help maintain proper airflow and cabinet alignment. What it does:

• Covers and protects the condenser/vent area at the front lower cabinet
• Directs airflow for efficient cooling circulation behind the grille
• Replaces cracked, broken, or loose trim that rattles or looks damaged
• Restores a finished, factory appearance to the lower front of the appliance

• Disconnect power to the appliance before starting work
• Typically secures with clips or screws—use care to avoid breaking retaining tabs
• Remove lower kickplate or toe panel as needed to access mounting points

This gas valve assembly controls gas flow to the appliance's burner, restoring reliable ignition and heating when the original valve fails. It replaces a faulty or leaking valve to help the unit heat safely and consistently. What it does:

• Regulates and routes gas to the burner based on the appliance's control signals
• Prevents gas flow when the appliance is off or during safety shutoff conditions
• Commonly used to address symptoms like no heat, weak heating, or a persistent gas smell when confirmed at the valve
• Works as the appliance's primary gas control component in the fuel delivery system

• One gas valve assembly

• Turn off gas supply and disconnect power before servicing; verify both are isolated
• Inspect all gas fittings and use an approved leak detection method after installation
• Do not modify the part; use proper tools and follow manufacturer service instructions

This gas valve assembly controls the flow of natural gas to the oven/range burners so the appliance can heat correctly. Replaces a failed valve to restore regulated gas delivery and safe ignition control. What it does:

• Regulates gas flow to the oven/range burner(s) during ignition and operation
• Works with the igniter and safety sensors to allow reliable burner lighting
• Common symptom: oven or burner fails to heat or maintain temperature
• Common symptom: appliance won't ignite or cycles without producing heat

• Turn off gas supply and disconnect power before starting any service
• Inspect and replace any worn gaskets or seals; check fittings for proper torque
• After installation, test for proper operation and check all connections for leaks with a soap solution or approved leak detector

This gas valve assembly controls gas flow to the oven and burners so the range heats properly and maintains safe operation. Replace a failed valve to restore ignition and regulated gas delivery. What it does:

• Regulates gas flow to the oven/burner when the appliance calls for heat
• Enables proper ignition and sustained burner/oven flame
• Common symptom: oven or burners won't heat or light even when controls are set
• Can cause clicking or continuous ignition attempts when valve sticks or fails

• Turn off gas supply and unplug the appliance before starting repairs
• Check all fittings for leaks after installation using a soap solution or approved leak detector
• Do not force connections; replace any damaged seals or tubing to ensure safe operation

This gas valve assembly controls and delivers gas to the burner when the appliance calls for heat. Replacing a failing valve restores reliable ignition, steady flame, and consistent heating performance while maintaining proper safety shutoff when not heating.

• Regulates gas flow to the burner(s) under the appliance's control and safety circuits
• Provides positive gas shutoff when no heat is requested
• Helps resolve no heat/flame, igniter glows or sparks but no ignition, burner lights then goes out, or intermittent heating
• Before replacement, also inspect the igniter, flame sensor, wiring, and regulator settings

• Disconnect electrical power and turn off the gas supply before servicing
• Note connection orientation; transfer any required fittings or brackets from the original valve
• Use an approved gas-rated thread sealant where applicable and leak-test all joints with a soap solution after installation
• Verify proper ignition and stable flame per the product's service or test procedure

The Burner Head is an OEM part for LG gas ranges. It sits securely at the center of each gas burner unit, featuring precision-engineered ports that control the size and pattern of flames.

Causes of burner head failure can include warping or damage to ports from extended heat exposure. Mineral buildup also distorts optimized air and gas mixing over time.

Symptoms of a problematic burner head include:

• Irregular or unevenly distributed flame
• Spots of excessive heat or cold spots on cookware
• Inability to maintain consistent temperatures

This LG part is also compatible with some Kenmore models.
 

The Burner Cap is an OEM part for LG gas cooktops and ranges. It sits atop each gas burner, acting as a protective cover and flame spreader. The precisely shaped cap facilitates even heat distribution by dispersing the gas flame across its surface.

Causes of a bad burner cap can include warping or deformation from high heat exposure overtime. Small cracks or breaks may also occur due to accidental impact or mishandling.

Symptoms of a bad burner cap include:

• Uneven or inefficient cooking as flames are not properly dispersed
• Yellow or orange flame coloring instead of the normal blue
• Burner making popping/crackling noises during use
• Safety issues such as potential flames escaping around the sides

This LG part is also compatible with some Kenmore models.

The Burner Cap is an OEM component specifically designed for LG gas ranges. This cap sits atop each burner element and functions to safely contain the burner flame during cooking. 

The burner cap regulates burner temperature and optimizes heat conduction. It distributes the flame evenly across the bottom of the cookware for rapid, consistent cooking results. 

Symptoms of a bad burner cap include: 

• Warping, cracks, or holes that allow flame to escape 
• Discoloration or material fatigue affecting flame quality
• Loose fit that impacts flame control or introduces safety issues

Causes may include normal wear over time exposed to heat, burns, or bending from heavy pots/pans.

Replacing this OEM LG burner cap will restore your range's heating performance, avoid potential safety hazards, and maintain proper cooking temperatures.

The Burner Cap is an OEM part for LG gas ranges. It sits securely over each sealed burner unit to direct flame upward for focused cooking power.

Causes relate to mineral deposits from years of flame exposure leading to reduced airflow. Damage may occur from rough pot handling as well.

Symptoms of a faulty burner cap can include:

• Yellowing or excessive carbon buildup
• Uneven browning or hotspots on pots and pans
• Flames not fully contained under cookware

This LG part is also compatible with some Kenmore models.
 

The Burner Cap is an OEM replacement part for LG gas cooktops and ranges. This cap covers the flame ports of each gas burner element.

Causes of a faulty or damaged cap could relate to warping or cracks accumulated over years of exposure to heat. Occasional spills that seep beneath can corrode metal exterior finishes as well.

Symptoms of a faulty cap include: 

• Improper or uneven flame pattern below each burner 
• Potential gas leaks emerging around damaged ports
• Aesthetic flaws detract from the cooktop design

This OEM component preserves styling on compatible Kenmore gas ranges. 

This cable assembly routes power and control signals between the appliance control board and components, restoring reliable communication and operation. Replace a damaged harness to correct intermittent power, control failures, or communication errors. What it does:

• Carries power and signal connections between the control board and appliance components
• Prevents intermittent operation caused by frayed, broken, or loose wires
• Stops control panel errors and component non-response due to faulty connections
• Maintains proper routing to avoid shorts and connector damage

• Disconnect power (unplug or shut off breaker) before beginning any repair
• Handle connectors gently and fully seat each plug to ensure a solid connection
• Route the harness exactly as the original to prevent pinching or rubbing

This rigid molded pipe assembly routes water or drainage inside the appliance to ensure proper flow and prevent leaks. Replace a cracked, clogged, or damaged tube to restore reliable water movement and reduce leaks. What it does:

• Channels water or condensate between internal components for normal operation
• Prevents leaks caused by cracked or split tubing
• Helps restore normal filling, dispensing, or draining when the original pipe is blocked or broken
• Fits where a single molded or formed pipe is required to maintain proper routing

• One rigid molded pipe assembly

• Disconnect power and shut off water supply before beginning repairs
• Inspect surrounding fittings and seals; replace any damaged clamps or gaskets
• Securely fasten both ends and check for leaks after reconnecting water

The Switch is an OEM part for LG ovens. This switch is responsible for turning the oven light on and off when the door is opened and closed. It ensures that the oven light operates correctly, providing visibility inside the oven cavity when the door is opened.

A bad oven door light switch can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as the oven light not turning on or off when the door is opened or closed, it may be time to replace the light switch.

Symptoms of a bad switch include:

• Oven light not turning on when the door is opened
• Oven light not turning off when the door is closed

Ensure proper function in your LG oven by replacing the faulty switch with this genuine OEM part.

This LG replacement part is also compatible with select Kenmore models.
 

This genuine replacement power cord assembly restores electrical power to the appliance by replacing a damaged or worn main power cable. It provides a direct, factory-fit connection for safe, reliable operation. What it does

• Delivers mains power from the wall outlet to the appliance's internal wiring and control systems.
• Replaces frayed, cut, melted or otherwise damaged cords that can cause loss of power or intermittent operation.
• Helps eliminate burning smells, visible damage, or exposed wires that indicate a compromised power connection.
• Restores a secure plug and strain-relief connection to reduce stress on terminal connections.

• One power cord assembly.

• Always disconnect power at the breaker or unplug the appliance before starting any work.
• Verify correct cord routing and secure the strain relief/retainer to prevent pinching or chafing.
• Tighten terminal screws to the manufacturer's specification and ensure proper grounding.

This AC fan motor circulates air inside the refrigerator to help maintain even temperatures and efficient cooling. Replaces a failed or noisy motor to restore proper airflow and prevent warm spots or frost buildup. What it does:

• Spins the evaporator/condenser fan blades to move air across coils for cooling
• Restores airflow when the fan has stopped running or runs intermittently
• Reduces noise if the original motor is shaky, grinding, or vibrating
• Helps prevent temperature fluctuations and excessive frost/ice buildup

• Disconnect power to the appliance before attempting service
• Handle wiring and connectors carefully; note connector locations before removal
• Motor mounts and fan blade hardware may need to be reused; keep screws and brackets together
• Test operation after installation and verify correct airflow direction

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

The Bracket Assembly is an OEM component specifically designed for LG electric ranges utilizing rear-mount control panels. This integral assembly securely attaches the command console within the unit cabinetry.

Causes of a bad bracket can include loosening or stripped screws no longer maintaining a tight interface, impacts warping the steel base compromising flush mounting, or corrosion where dissimilar metals contact deteriorating securing points.

Symptoms of a bad bracket assembly include: 

• Loose panel unable to be properly reinstalled  
• Scratches or abrasions from rattling components
• Drooping controls suffering misaligned activation zones  
• Detached splash guard failing to fully protect surfaces

Replace yours today with this genuine OEM LG assembly to restore a robust interface. Backed mounting flanges deliver long-term stability and compatibility when replacing Samsung, Frigidaire, or GE electric ranges requiring rear console mounting as well. 

A convection fan assembly that circulates hot air inside the oven cavity to promote even baking and roasting. Replacing a worn or noisy fan helps restore consistent cooking performance and airflow in convection ovens. What it does:

• Circulates heated air for more even temperature distribution and improved browning.
• Restores proper airflow when the existing fan is noisy, loose, or failing to spin.
• Helps resolve uneven baking, hot spots, or longer cook times caused by poor air circulation.
• Works as the rotating airflow component of the oven's convection system.

• Disconnect power to the appliance before beginning any work to avoid shock risk.
• Access typically requires removing the oven interior panel or rear access panel; keep track of fasteners.
• Handle sharp sheet-metal edges and support the fan while disconnecting wiring or mounting hardware.

This insulating mounting piece helps isolate and secure components inside the appliance, preventing electrical contact and reducing vibration. It restores proper spacing and insulation where the original insulator is cracked, worn, or missing. What it does:

• Provides electrical insulation between adjacent components to reduce shorting risk
• Maintains correct component spacing and alignment for reliable operation
• Dampens vibration and helps prevent rattling or movement of nearby parts
• Common repair for visible cracks, deformation, or missing/broken insulating mounts

• One insulator mounting piece as shown

• Turn power off and unplug the appliance before servicing to avoid shock
• Verify location and orientation of the old insulator before removal; replace like-for-like
• Use appropriate hand tools; avoid over-tightening fasteners that could deform the insulator

A replacement motor bracket that secures the motor to the appliance chassis for stable operation and reduced vibration. Restores proper motor alignment to help maintain smooth, quieter cycles and protect drivetrain components. What it does:

• Holds the motor firmly in place to prevent movement during operation
• Maintains correct motor-to-transmission/gear alignment for reliable power transfer
• Reduces vibration and rattling that can occur when mounts fail
• Helps prevent premature wear of motor and connected components
• Addresses symptoms such as excessive noise, shaking, or motor misalignment

• Disconnect power to the appliance before servicing; follow lockout/tagout best practices
• Turn off water supply and relieve any residual pressure for washer models before disassembly
• Basic mechanical skills and common hand tools required; bracket removal may require loosening motor fasteners and supports
• Reuse OEM fasteners if undamaged and torque to manufacturer specs; inspect surrounding mounts and hardware for wear

This halogen oven lamp provides interior lighting so you can check food without opening the door. It restores clear, bright illumination for safer, easier cooking and monitoring in compatible ovens. What it does:

• Replaces a burned or flickering oven interior lamp to restore normal lighting
• Lets you view cooking progress without opening the oven door
• Helps reduce the need for extra kitchen lights when checking food
• Fits into the oven lamp socket and functions as the appliance's interior light source

• One halogen oven lamp

• Disconnect power to the appliance before servicing to avoid shock
• Allow the oven to cool fully before replacing the lamp to avoid burns
• Handle the bulb by the base or use gloves/tissue to keep oils off the glass
• Make sure the bulb is seated securely in the lamp socket before restoring power

This packing gasket is the replacement door seal that helps maintain an airtight barrier to keep interior temperatures stable and prevent moisture or air leaks. Replaces a worn or damaged gasket to restore proper sealing performance. What it does:

• Seals the door opening to reduce air leaks and help maintain interior temperature
• Helps prevent moisture buildup and frost inside the compartment
• Restores correct alignment and contact where the door meets the cabinet
• Commonly replaced when the existing gasket is torn, deformed, or no longer seals evenly

• One packing gasket

• Disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the mating surface before installing the new gasket
• Work around the perimeter, pressing the gasket into the channel for an even fit; avoid stretching the gasket excessively
• If adhesive, fasteners, or clips are required, use only OEM-recommended materials and follow manufacturer guidance

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

This is a replacement pipe used to route fluid inside the appliance, restoring proper flow and preventing leaks. It's a direct-fit service part that replaces a damaged or worn tubing section for reliable operation. What it does:

• Directs water flow between components to maintain normal dispensing and circulation.
• Replaces cracked, split, or corroded tubing that can cause leaks or pooling.
• Helps stop intermittent or continuous drips and wet spots under or behind the appliance.
• Restores sealed connections when paired with proper clamps or fittings.

• One replacement pipe

• Disconnect power and shut off the water supply before beginning any repair.
• Handle carefully to avoid kinking; inspect and replace any worn clamps or seals.
• Use appropriate tools and follow the OEM parts diagram for routing and connection points.

This pipe routes water inside the appliance to supply the dispenser and ice-making components, restoring reliable water flow and helping prevent leaks from damaged or clogged tubing. It's a direct-fit replacement designed to match OEM routing. What it does:

• Channels water from the inlet to the ice maker/dispenser assembly.
• Maintains correct internal water flow for ice production and dispensing.
• Replaces cracked, pinched, or corroded tubing that can cause leaks.
• Helps stop intermittent or reduced water flow caused by damaged piping.

• Disconnect power and shut off the water supply before starting.
• Inspect and, if needed, replace any adjacent clamps, gaskets, or fittings to ensure a leak-free seal.
• Re-route tubing to match original OEM path; avoid kinks or sharp bends.
• After installation, restore water and power, then check all connections for leaks while running a water/ice cycle.

The Broil Burner Orifice Holder Assembly is an OEM part for LG gas ranges. This assembly includes the burner located at the top of the range oven cavity used for powerful broiling functions. 

Symptoms of a bad broil burner assembly include:

• Inadequate or uneven broiling performance
• Diminished heating ability in the broil setting  
• Burner fails to ignite or light properly
• Burner makes sputtering or clicking noises

Causes of failure can include clogged or damaged orifices, worn-out gaskets or seals, or cracks in burner tubing that allow gas leakage.

Replace yours today with this genuine LG replacement part to restore optimal broiling performance. This OEM assembly is also compatible with the Kenmore Elite brand.

The Burner Assembly is an OEM component specifically designed for LG gas ranges equipped with sealed cooktop burners. This integral assembly contains the ignition electrode, valve stem, and cast burner head to conduct flame across grates.  

Symptoms of a bad burner assembly include:

• Inability to ignite or maintain consistent flames under cookware
• Yellow broken or excessive flame instead of steady blue  
• Clicking ignition sounds but no combustion takes place
• Deteriorated valve stems limiting gas flow regulation

Causes of failure involve clogged ports blocking gas dispersion, cracked burner bases no longer supplying sufficient air intake, or damaged ignition systems disabling piezo sparks over dozens of heating cycles.

Replace yours today with this genuine OEM LG assembly to restore optimal cooktop performance. Factory-sealed construction withstands daily use maintaining even heat across pans and preventing gas leaks. Compatible with GE, Frigidaire, and Kenmore sealed burner models as a direct unit replacement.

This burner assembly is the complete replacement component that provides the flame source for gas cooktops or ranges, restoring reliable ignition and heating when the original burner is damaged or worn. What it does

• Houses the burner ports and distributes gas to produce an even flame for cooking
• Works with the ignition system to light when the control signals for heat
• Helps prevent gas leaks when undamaged; a cracked or corroded burner can cause uneven heating or visible flame irregularities
• Commonly replaced when burners are physically warped, clogged beyond cleaning, or otherwise failing to light properly

• One complete burner assembly

• Disconnect gas and power supply and follow the appliance manufacturer's safety instructions before starting
• Inspect adjacent components (igniter, valve, or orifice) for damage while replacing the burner
• Use proper tools and torque; replace all gaskets or fasteners removed during service

This governor assembly is the mechanical control that stabilizes and regulates motion within the appliance's drive mechanism. Replacing a worn governor restores smooth, consistent operation and helps prevent erratic movement that can strain connected components. What it does:

• Regulates and limits the speed/rotation of the linked drive for stable, predictable movement
• Helps synchronize gears or shafts so the mechanism operates smoothly
• Common symptoms: intermittent or no movement, jerky/erratic motion, clicking or grinding noises
• Visible wear, cracks, or a loose/broken hub on the original governor

• 1 governor assembly

• Disconnect power before servicing; allow moving parts to come to a complete stop
• Note the original orientation; take photos to aid reassembly
• Transfer any reusable brackets, clips, or spacers from the original if required
• After installation, rotate the mechanism by hand to verify free movement before restoring power

This cabinet base is the lower structural support that secures the washer tub and components, helping keep the appliance stable and aligned for reliable operation and reduced vibration. What it does:

• Supports the washer cabinet and internal components to maintain proper alignment
• Helps reduce excessive vibration and movement during spin cycles
• Keeps internal parts positioned to prevent rubbing or contact that can cause noise
• A damaged or cracked base can contribute to rocking, unusual noises, or misalignment

• One cabinet base

• Disconnect power and water before beginning any repair and work on a stable surface
• Replacement may require lifting or tilting the washer and removing the outer cabinet — two people recommended
• Retain and reuse any mounting hardware only if undamaged; replace stripped or corroded fasteners

Replacement burner assembly that restores proper operation to a single cooktop burner. Installs in the surface burner area to help the burner ignite and deliver consistent, reliable heat for everyday cooking. What it does:

• Replaces a damaged or worn surface burner assembly to restore ignition and stable heating
• Stops common symptoms like a burner that won't light, has a weak or uneven flame, or fails to heat consistently
• Houses the burner components that direct and control the flame for one cooktop burner
• Works as a direct replacement when the original surface burner assembly is worn, cracked, or malfunctioning

• Turn off power and gas supply before beginning any service
• Follow the appliance manufacturer's service instructions and use proper tools; keep small fasteners and seals in place
• After installation, test ignition and flame operation; if you smell gas or see abnormal flame behavior, shut off the appliance.

This front plate is the outer-facing panel that restores the appliance's appearance and protects internal components from everyday contact. It fits where the original front panel was installed and provides a finished look. What it does:

• Replaces a cracked, dented, or discolored front panel to improve appearance
• Shields controls and internal parts from dust and accidental contact
• Helps maintain proper alignment of adjacent panels and trim
• Prevents small objects from entering the appliance cavity through the front

• One front plate

• Disconnect power to the appliance before starting any work
• Remove surrounding trim or screws to access and replace the panel; keep fasteners for reassembly
• Handle carefully to avoid scratching the finished surface during installation

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

The Rail Guide is an OEM part for LG ranges. It directs the movement of adjustable storage drawers in and out of position for easy access.

Causes relate to repeated impacts over many years of use. Heat exposure also warps metal clips holding accurate alignment.

Symptoms of a faulty drawer rail guide may include:

• Excessive noise or vibration during opening/closing
• Difficulty fully extending or retracting the drawer
• Potential for pinched fingers if collapsing edges occur

This LG part is also compatible with some Kenmore models.
 

The Gas Valve is an OEM replacement part for LG gas ranges. This valve regulates the flow of natural gas from the supply line into the burners of the range. It functions to adjust gas pressure and control the burner flames according to temperature and cooking settings. 

Symptoms of a bad gas valve include: 

• Burners that do not ignite or that ignite intermittently
• Flames that are too high, too low, or uneven 
• Inability to adjust or control burner flames
• Gas smells coming from the range

Causes of a bad gas valve include wear and tear over time, damage from repeated use or improper handling, or issues with the electronic components that operate the valve. 

This OEM LG replacement part is also compatible with Sears/Kenmore models.

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening

This factory accessory assembly replaces a missing or damaged original so your appliance installs and operates as designed. Use it to restore the proper fit, alignment, and securement of the related component on compatible units. What it does:

• Provides the specific accessory group used to mount, secure, or complete the associated component
• Restores correct fit and alignment when the original piece is cracked, warped, or lost
• Helps eliminate looseness, rattling, or poor appearance caused by damaged or missing trim/hardware
• Common symptoms include a missing part, visible damage, poor fit, or vibration/rattling after service or a move

• 1 accessory assembly

• Disconnect power; shut off water or gas supply if applicable before servicing
• Refer to your model's exploded-view diagram or service manual to confirm location and orientation
• Retain and reuse original fasteners unless replacements are provided with the assembly
• Wear cut-resistant gloves; verify secure fit and proper operation after installation