Parts for Lg LSGL5833D/00: Controller Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Insulator for electric and gas ranges. Installs between internal components to provide heat or electrical protection. Replace if cracked or missing.

Replacement screw secures panels and components in your microwave. Install when original hardware is stripped, rusted, or missing to stop rattles.

Secures interior panels and components. Replace when stripped, corroded, or missing to stop rattles and secure loose trim. Verify fit with your model number.

Machine screw for electric and gas ranges. Secures internal components and panels. Replace if screw is stripped, missing, or damaged during service work.

Wire harness for electric and gas ranges. Connects electrical components inside your range. Replace if wires are damaged, frayed, melted, or connections are loose.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

Replacement washer that secures fasteners and distributes load at connection points in ranges and ovens. Needed when original is missing, worn, or damaged.

Replacement screw for electric and gas ranges. Secures internal components and panels. Needed when original is stripped, missing, or damaged during repair.

Secures panels, brackets, and internal components in your range. Replace this screw if the original is missing, stripped, or rusted for proper fit.

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

Secures panels, brackets, and trim on your gas range. Replace this self-tapping fastener if it's missing, stripped, or damaged to restore alignment.

The Screw is an OEM component specifically designed for LG ranges. It plays an important mounting and fastening role by securely attaching internal components together.

The screws utilized within the range cabinet ensure sturdy construction and reliable mechanical cohesion. They allow for simple assembly and proper alignment of inner parts. 

Causes of bad screws can include wear and tear over time, or damage from overtightening leading to stripped threads or heads.

Symptoms of bad screws include:

• Loose, detached, or misaligned inner parts  
• Hardware that does not fit or interface as designed
• Unintended noises or movement during the operation

This OEM LG replacement part is also compatible with Sears/Kenmore and some GE ranges utilizing similar fasteners. Replacement ensures the range remains mechanically sound.
 

This 4.0x16mm tapping screw secures trim, panels, and brackets on ranges and microwaves. Replace missing, stripped, or damaged screws during repair.

Factory-style screw for securing panels, brackets, and assemblies on gas ranges and cooktops. Replace if missing, stripped, or damaged during repairs.

Fix gas range that won't heat, ignite, or turn on with this power control board assembly. Controls oven temperature and burner operation. Moderate DIY repair.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

Adjustable metal leveling foot that elevates and stabilizes your range. Mounts to the bottom of the unit. Replace if broken, worn, or missing.

Replaces cracked or dented outer door trim to restore your range's appearance and seal support. Replace when damaged to maintain proper door sealing. Confirm fit.

Replacement door handle for electric and gas ranges. Installs on the oven door to restore safe opening and closing. Replaces cracked, broken, or worn handles.

This is the outer door panel assembly that forms the exterior surface of the oven door. It provides structural support and houses the door handle mounting points while contributing to heat insulation. Replace this panel if it is dented, cracked, rusted, or if the outer glass or trim is damaged beyond repair.

Replacement window glass for range oven doors. Restores clear viewing area when original glass is cracked, chipped, cloudy, or shattered. Installs inside door.

Replace your range oven door hinge assembly when the door sags, binds, or won't close properly. Restores alignment and smooth operation. Verify fit with your model.

Support bracket for range oven door window glass. Secures and stabilizes the inner window panel. Replace if cracked, broken, or missing to restore door.

Safety cover for electric and gas ranges. Installs over internal components to protect wiring and mechanisms. Replace if cracked, broken, or missing.

Single wire harness for gas ranges. Connects electrical components inside your range. Replace if wires are frayed, damaged, or connections are loose.

Wire harness for electric and gas ranges. Replaces damaged, frayed, or worn wiring harnesses. Essential for restoring proper electrical connections.

This ring guide supports and centers the microwave oven's glass turntable so it rotates smoothly for even cooking. It replaces a cracked or worn guide to reduce wobble and noisy operation. What it does:

• Centers and supports the glass tray so it turns evenly on the roller/drive assembly
• Helps keep the tray from slipping or wobbling during rotation
• Restores smooth, quiet turntable movement when the original guide is damaged
• Addresses symptoms such as a tray that wobbles, binds, or does not rotate properly

• One ring guide

• Disconnect power before servicing the appliance
• Remove the glass tray and roller assembly to access the guide
• Set the new guide into place on the turntable support/roller path and reinstall the roller and glass tray
• Handle the glass tray carefully; replace rollers or the drive coupling if worn

Range won't change settings when you turn the control knob? This rotary selector switch restores cycle selection and user control over appliance functions.

The PCB Assembly is an OEM part for LG refrigerators. It stands for Printed Circuit Board, which is the main control board that manages and regulates various functions and components within the refrigerator.

Symptoms of a bad PCB Assembly include:

• The refrigerator not powering on or displaying any lights/indicators
• Specific components or features not functioning correctly (ice maker, dispenser, cooling, etc.)
• Error codes or warning lights illuminated on the control panel
• Strange noises or abnormal behavior from the refrigerator

Causes of a bad PCB Assembly can be related to electrical faults, such as short circuits, power surges, or component failures. Physical damage from impact, moisture exposure, or overheating can also contribute to the malfunction of the PCB.

This OEM LG part is also compatible with Sears/Kenmore refrigerators. 

This is the control panel assembly for a range or oven, which includes the user interface and associated electronic components. It allows you to set cooking modes, temperature, and timer functions. Replace this assembly if the panel display is malfunctioning, buttons are unresponsive, or the overlay is peeling or damaged.

Replaces worn, cracked, or missing control knob on your gas range. Snaps securely onto the control shaft to restore precise temperature selection.

Replace a damaged motor cover causing excessive noise or debris buildup. This housing shields the motor assembly and maintains proper airflow. DIY-friendly.

Idle packing bushing for electric and gas ranges. Replaces worn, cracked, or missing bushings. Ensures proper fit and cushioning for range components.

Replace your range motor cover if the motor assembly is exposed or damaged. This protective housing shields internal components from dust and debris.

Decorative trim piece that surrounds the rear of your range for a finished appearance. Replace if cracked, chipped, damaged, or missing for restored looks.

Replace your cracked, warped, or missing range oven rack. Installs inside the oven cavity to support cookware during baking, roasting, and broiling.

This is a cast iron or porcelain-coated burner grate that sits on top of the range surface over a gas burner, providing a stable platform for cookware. It supports pots and pans above the flame for even heating. Replace this grate if it is cracked, chipped, warped, or if its finish has deteriorated to the point where cookware no longer sits level.

This is a center burner grate that sits on the cooktop surface and supports pots and pans over the burner. It provides a stable, elevated cooking surface to allow proper heat circulation. Replace this grate if it is cracked, warped, has broken supports, or its finish has deteriorated to the point where cookware no longer sits level.

Controls gas flow to your range burner. Replace this valve assembly when the original is faulty, leaking, or damaged to restore safe gas regulation.

If your range burners won't light or heat unevenly, the gas valve assembly may have failed. This part regulates gas flow to restore proper ignition.

Gas range won't ignite or heat properly? This valve assembly controls gas flow to your oven and burners. Restores ignition and safe operation.

The Burner Head is an OEM part for LG gas ranges. It is located underneath the burner caps and is responsible for producing the ignited flame during cooking. 

Symptoms of a bad burner head include: 

• Difficulty lighting or sustaining a flame
• Unbalanced or irregular burner performance  
• Yellow flame tips or soot buildup
• Burner tubes appearing warped or misshapen

Causes of a faulty burner head can be issues like cracks in the burner material, blockages within the gas tubes, or deformations from long-term heat exposure.

 This burner head is also compatible with select Sears/Kenmore gas range models.

Replace your gas range burner head if flames are uneven, won't ignite, or produce yellow/orange flames. Controls ignition and flame for each burner.

Replace a gas range burner head with uneven flames, weak heat output, or clogged ports. Sits at the center of the burner unit to control flame pattern.

Fix uneven flames or poor heat distribution with a new burner cap. Covers the burner head to ensure proper gas flow and heat transfer on your cooktop.

Fix uneven flames or yellow burner tips with this gas range burner cap. Spreads flame evenly across the burner surface. Simple 5-minute swap.

Replace a burner cap when flames are uneven, yellow, or won't stay lit. This cap distributes heat evenly across your cooktop. Simple 5-minute swap—no tools.

Burner cap sits over sealed burner units to direct flame upward. Replace if cracked, chipped, or damaged from wear. Lifts off easily for quick replacement.

If your gas burner flame is uneven or yellow, the burner cap may be warped or cracked. This component covers flame ports for proper heat distribution.

Fix intermittent power or control failures with this gas range cable assembly. Routes power between the control board and components to restore operation.

This pipe assembly directs water between components to restore proper draining or water flow and prevent leaks. It replaces a damaged or worn factory tube so the appliance can move water where it belongs. What it does:

• Channels water between internal components to support normal draining and circulation
• Helps stop leaks caused by cracked, split, or clogged tubing
• Restores proper water routing that can trigger error codes or poor performance
• Used when visible damage, water pooling, or persistent drainage issues occur

• One pipe assembly as shown

• Turn off power and shut off the water supply before replacing the part
• Inspect clamps and fittings; replace any melted, broken, or corroded hardware
• Ensure proper seating and secure all connections to prevent leaks

Burner pipe for gas ranges. Delivers gas from manifold to burner assembly. Replace if cracked, corroded, or leaking to restore proper gas flow.

The Switch is an OEM part for LG ovens. This switch is responsible for turning the oven light on and off when the door is opened and closed. It ensures that the oven light operates correctly, providing visibility inside the oven cavity when the door is opened.

A bad oven door light switch can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as the oven light not turning on or off when the door is opened or closed, it may be time to replace the light switch.

Symptoms of a bad switch include:

• Oven light not turning on when the door is opened
• Oven light not turning off when the door is closed

Ensure proper function in your LG oven by replacing the faulty switch with this genuine OEM part.

This LG replacement part is also compatible with select Kenmore models.
 

This genuine replacement power cord assembly restores electrical power to the appliance by replacing a damaged or worn main power cable. It provides a direct, factory-fit connection for safe, reliable operation. What it does

• Delivers mains power from the wall outlet to the appliance's internal wiring and control systems.
• Replaces frayed, cut, melted or otherwise damaged cords that can cause loss of power or intermittent operation.
• Helps eliminate burning smells, visible damage, or exposed wires that indicate a compromised power connection.
• Restores a secure plug and strain-relief connection to reduce stress on terminal connections.

• One power cord assembly.

• Always disconnect power at the breaker or unplug the appliance before starting any work.
• Verify correct cord routing and secure the strain relief/retainer to prevent pinching or chafing.
• Tighten terminal screws to the manufacturer's specification and ensure proper grounding.

This AC fan motor powers the convection fan inside the oven cavity, circulating hot air for even cooking and baking. It mounts behind the rear panel of the oven and drives the fan blade that distributes heat throughout the compartment. Replace this motor if the oven heats unevenly, the convection fan is not spinning, or you hear unusual noises coming from the back of the oven during convection cooking.

Wire harness assembly for gas ranges. Connects electrical components within the appliance. Replace if wires are frayed, connections are damaged, or loose.

If your oven won't reach the right temperature or shows an F9 error, the temperature sensor may be faulty. Simple DIY repair in under 45 minutes.

Replace a damaged or corroded wire harness in your range. This single-connection harness restores proper electrical connections when original wiring is frayed, melted, or broken.

Secures the control panel to your range cabinet. Replace if the bracket is cracked, bent, stripped, or hardware no longer holds the console firmly in place.

Single wiring harness for electric and gas ranges. Replaces damaged, frayed, or corroded harnesses. Essential for restoring electrical connections.

Fixes uneven baking or convection not working in your range. This fan blower assembly circulates hot air for even cooking. Moderate repair difficulty.

Fixes uneven baking and noisy oven operation. This convection fan assembly circulates hot air for consistent cooking. Moderate DIY repair restores airflow.

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

Insulator for gas range burners. Installs beneath burner components to provide heat protection. Replace if cracked, broken, or missing for proper operation.

Replace your damaged or broken range handle bar. This bar installs on the oven door, providing a secure grip for opening and closing. Order now.

Fixes uneven rotation or component failure in your range. This synchronous motor assembly restores precise speed control. Moderate DIY repair.

Motor loose or vibrating excessively? This motor bracket secures the motor to the chassis, reducing vibration and maintaining alignment for quieter operation.

Halogen oven light bulb illuminates your range interior for monitoring food while cooking. Replace when bulb burns out or flickers. Verify fit with your model.

This hinge bracket secures the oven door hinge mechanism on your range. Replace if the bracket is cracked, broken, bent, or missing to restore door support.

Seals your range door to maintain stable temperatures and prevent air leaks. Replace when worn, cracked, or no longer creating an airtight seal.

Seals your range oven door to prevent heat loss and maintain even cooking. Replace if worn, cracked, or causing temperature issues. Confirm fit with your model.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

This is a replacement pipe used to route fluid inside the appliance, restoring proper flow and preventing leaks. It's a direct-fit service part that replaces a damaged or worn tubing section for reliable operation. What it does:

• Directs water flow between components to maintain normal dispensing and circulation.
• Replaces cracked, split, or corroded tubing that can cause leaks or pooling.
• Helps stop intermittent or continuous drips and wet spots under or behind the appliance.
• Restores sealed connections when paired with proper clamps or fittings.

• One replacement pipe

• Disconnect power and shut off the water supply before beginning any repair.
• Handle carefully to avoid kinking; inspect and replace any worn clamps or seals.
• Use appropriate tools and follow the OEM parts diagram for routing and connection points.

Gas pipe that connects the gas supply to the burner assembly in your gas range. Replace if the pipe is cracked, corroded, or leaking to restore safe operation.

This pipe routes water inside the appliance to supply the dispenser and ice-making components, restoring reliable water flow and helping prevent leaks from damaged or clogged tubing. It's a direct-fit replacement designed to match OEM routing. What it does:

• Channels water from the inlet to the ice maker/dispenser assembly.
• Maintains correct internal water flow for ice production and dispensing.
• Replaces cracked, pinched, or corroded tubing that can cause leaks.
• Helps stop intermittent or reduced water flow caused by damaged piping.

• Disconnect power and shut off the water supply before starting.
• Inspect and, if needed, replace any adjacent clamps, gaskets, or fittings to ensure a leak-free seal.
• Re-route tubing to match original OEM path; avoid kinks or sharp bends.
• After installation, restore water and power, then check all connections for leaks while running a water/ice cycle.

Burner nozzle holder for gas ranges. Secures the gas nozzle in place on the burner assembly. Replace if cracked, broken, or missing to restore proper fit.

Fix inadequate or uneven broiling in your gas range with this broil burner orifice holder assembly. Restores proper heat distribution for cooking.

Fixes weak or uneven flames on gas range burners. This burner nozzle regulates gas flow for proper flame height. Simple DIY fix, takes 15 minutes.

The Burner Assembly is an OEM component specifically designed for LG gas ranges equipped with sealed cooktop burners. This integral assembly contains the ignition electrode, valve stem, and cast burner head to conduct flame across grates.  

Symptoms of a bad burner assembly include:

• Inability to ignite or maintain consistent flames under cookware
• Yellow broken or excessive flame instead of steady blue  
• Clicking ignition sounds but no combustion takes place
• Deteriorated valve stems limiting gas flow regulation

Causes of failure involve clogged ports blocking gas dispersion, cracked burner bases no longer supplying sufficient air intake, or damaged ignition systems disabling piezo sparks over dozens of heating cycles.

Replace yours today with this genuine OEM LG assembly to restore optimal cooktop performance. Factory-sealed construction withstands daily use maintaining even heat across pans and preventing gas leaks. Compatible with GE, Frigidaire, and Kenmore sealed burner models as a direct unit replacement.

Fix a burner that won't light or heat unevenly with this gas range burner assembly. Common repair for weak or inconsistent flames on cooktop surfaces.

Replace a burner assembly when flames are uneven, yellow, or won't light properly. Direct replacement part restores safe, efficient cooking performance.

This heater cover mounts over the dishwasher's heating element at the bottom of the tub. It shields the element and helps direct wash water, protecting dishes and the tub floor from direct contact with the heater. What it does:

• Covers and protects the exposed heating element at the tub base
• Helps channel water flow around the element during the cycle
• Replace if the cover is cracked, warped/melted, or missing
• Can help prevent utensils or items from snagging near the heater area

• 1 heater cover

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and, if needed, the lower spray arm and filters to access the heater area
• Release retaining tabs or screws, remove the old cover, and seat the new cover evenly
• Ensure the cover locks securely and the spray arm spins freely before restoring service

Pressure regulator assembly for gas ranges. Mounts to the gas supply line to control fuel pressure. Replace if cracked, leaking, or damaged.

This is a metal base panel that sits at the bottom of the upper oven cavity in a range. It serves as a heat shield and floor surface, protecting the lower cabinet structure from direct heat exposure while helping distribute heat evenly. Replace this panel if it is warped, rusted, or has holes that allow grease and food debris to fall into the lower compartment.

Fix a burner that won't ignite or heat evenly with this surface burner assembly. Restores consistent flame and reliable heat to your gas range cooktop.

Fixing frame that secures internal components in your range. Replace if your original frame is bent, cracked, or broken to properly mount parts inside the unit.

Rubber foot pad that supports and stabilizes your range on the floor. Replace if cracked, broken, worn, or missing to keep your appliance level.

This is a metal anti-tip bracket that secures the range to the floor or wall to prevent it from tipping forward. It is a critical safety device, especially when heavy items are placed on an open oven door. Replace or install this bracket if yours is missing, damaged, or if you are repositioning the range after a move or kitchen remodel.

Replacement slider for range drawers and panels. Restores smooth movement when original is worn, cracked, or broken. Mounts to moving components for alignment.

Replace worn range drawer sliders to restore smooth, quiet operation and proper alignment. Prevents damage to surrounding trim. Confirm fit with your model.

Replace a faulty oven temperature sensor if your range bakes unevenly, runs too hot or cold, or displays temperature errors. Moderate DIY repair.

Fix an oven that won't heat or gives F9 error code. This gas valve regulates gas flow to burners. Moderate DIY repair requiring basic tools.

Mounting anchor for range door handles. Replaces worn, broken, or missing anchors to restore secure handle attachment and eliminate wobbling or loose fit.