Parts for Maytag MVWP475EW0: 03 - Controls And Water Inlet Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.

Replacement screw for securing panels, brackets, and internal components. Replaces missing, stripped, or damaged fasteners to restore proper fit.

Fix a washer that won't start, stops mid-cycle, or shows error codes with this electronic control board. Moderately challenging repair requiring basic tools.

Rear panel for laundry center units. Covers the back of the appliance cabinet. Replace if cracked, dented, rusted, or missing for complete enclosure.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Console button not responding or stuck? This washer pushbutton restores tactile control operation. Direct-fit replacement for worn or broken buttons.

Washer won't turn on or has no power? This power cord connects your washer to the electrical outlet. Simple plug-in installation takes 10 minutes.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement control knob for your washer's console panel. Needed when the original knob is cracked, broken, or missing. Installs on the control panel.

This replacement name plate restores the appliance's exterior appearance by replacing a damaged, faded, or missing logo/trim plate. It provides a clean, factory-look finish so the model retains its original styling. What it does:

• Replaces a worn, cracked, or missing name plate to restore the appliance's exterior appearance
• Covers the same mounting area as the original so logo/branding and trim look correct
• Helps maintain resale value and overall cosmetic condition
• Fits and aligns with existing fasteners or attachment points for an OEM fit

• One replacement name plate

• Disconnect power or gas supply to the appliance before beginning work and follow all safety precautions
• Remove the old name plate carefully to avoid scratching the surrounding surface or damaging fasteners
• Install the new plate using the original screws, clips, or adhesive as applicable; do not force parts into place

Fix intermittent operation or control failures with this wire harness assembly. Restores electrical connections between components in your laundry center.

Fix a washer that won't fill, fills slowly, or won't stop filling. This water inlet valve controls water flow during wash cycles. 30-minute repair.

10 - 16 x 1/2

Fixes intermittent power loss or control failures. This main wire harness restores electrical connections between the control board and components.

Fix a washer that won't change cycles or respond to wash settings. This cycle selector switch restores proper cycle selection and operation.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.