Parts for Ge WPGT9150H0MG: 01 - Controls, Backsplash & Top Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

White touchpad control panel assembly for your washer. Replaces cracked, worn, or unresponsive control panels. Direct fit installation part.

Replace your washer's control panel touch pad if buttons are unresponsive, cracked, or worn. This touch pad assembly installs on the top panel.

This back panel is the exact exterior rear housing piece for the appliance, restoring proper enclosure and finished appearance while protecting internal components. It fits the original mounting locations and maintains factory airflow paths. What it does:

• Replaces a cracked, dented, or corroded rear housing that exposes internal parts
• Protects internal components from dust, moisture, and accidental contact
• Restores proper alignment for rear trim and mounting points
• Helps maintain intended airflow and clearance behind the unit

• Disconnect power and water before beginning service.
• Handle panel edges carefully; metal edges may be sharp.
• Reuse original screws and clips unless damaged; torque to OEM recommendations.

White top cover panel for washer lid assembly. Replaces cracked, broken, or damaged covers. Direct fit for compatible GE Profile top-load models.

White trim that finishes the edge around your washer lid. Replaces cracked, chipped, or broken trim that catches clothing or prevents smooth closing.

Right-side cap insert for your washer. Replaces the original cover if it's cracked, broken, or missing. Restores a clean, finished appearance to your machine.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a replacement mounting screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. Use it to replace a missing or damaged fastener for a secure repair. What it does:

• Secures panels, trim, brackets, or small components in place
• Restores proper panel alignment and reduces rattling or vibration
• Replaces stripped, missing, or corroded screws that cause loose parts
• Helps maintain electrical and mechanical connections by holding parts steady

• Turn power off and unplug the appliance before beginning any repair
• Use the matching driver or bit to avoid stripping the screw head
• Replace only with the same type and size screw for a proper fit
• Inspect surrounding parts for wear

Fix a washer that won't stop filling or leaks water with a new inlet valve assembly. Controls water flow during fill and rinse cycles. 30-minute DIY repair.

Fix detergent leaking before wash starts or not dispensing properly. This washer dispenser cup holds liquid or powder detergent until the correct cycle phase.

Screw and gasket assembly for washers. Secures components and ensures proper seal. Replace if screw is stripped, gasket is cracked, or assembly is missing.

Replace your washer's pressure switch hose if cracked, kinked, or leaking. This tube connects the pressure sensor to the tub for water level control.

Replace the control board wire harness in your washer. This wiring assembly connects the main control board to other components. Order now if damaged or frayed.

Directs hot water into your washer's fill valve. Replace this inlet hose if cracked, worn, or leaking to restore proper water connection and flow.

This bleach dispenser box is the plastic reservoir that holds and directs liquid bleach into the washer during the wash cycle, helping the machine deliver bleach safely and evenly. Fits select GE top-load washers. What it does:

• Holds liquid bleach until the washer adds it at the correct time
• Directs bleach into the wash tub to prevent concentrated bleach contact with clothes
• Helps prevent leaks from the dispenser area when functioning properly
• Common symptom: cracked or warped box causing leaks or bleach not dispensing

• 1 bleach dispenser box

• Turn off power and shut off water supply before starting work
• Replace only with the exact part to ensure proper fit and sealing
• Inspect surrounding gaskets and hoses; replace if damaged to avoid leaks

Secures washer hoses to prevent leaks. Replace if loose, cracked, or causing water seepage. Verify fit with your washer's model number before ordering.

Screw pack for washers. Secures internal components and panels. Replace if screws are stripped, missing, or damaged during appliance repair or maintenance.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.