Parts for Ge GNW128PSM0WW: Controls & Lid Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This RJ45 port is the appliance Ethernet jack that provides a secure wired network connection to the appliance control electronics. Replacing a damaged jack restores a solid plug-and-play Ethernet connection for diagnostics or network features. What it does:

• Provides a standard RJ45 receptacle for connecting an Ethernet cable to the appliance control board
• Restores a stable wired network connection when the existing jack is cracked, loose, or has bent pins
• Enables communication between the appliance and a home network or service tools that require a wired link
• Helps prevent intermittent connectivity caused by poor physical contact or damaged terminals

• 1 RJ45 port (Ethernet jack) as shown

• Power off and unplug the appliance before starting work to avoid electrical shock
• Access the control area; this part typically mounts to the control board or chassis
• Inspect mating cable and wiring for damage; replace or repair wiring harnesses if needed

Fix washer detergent not dispensing or drawer stuck issues. This dispenser drawer assembly holds and releases soap during wash cycles. Easy DIY fix.

If detergent leaks or pools in the dispenser, the dispenser box assembly may be cracked. This housing secures dispenser components. Moderate DIY repair.

A small replacement housing screw that secures appliance panels and brackets, restoring proper fit and preventing rattles or loose panels. Fits common appliance housings where a short ST4 x 12 self-tapping screw is required. What it does:

• Fastens housing panels, trim, or internal brackets to maintain proper alignment and reduce vibration
• Replaces missing or damaged screws that cause loose or rattling panels
• Works with sheet metal and plastic mounting points designed for ST4 thread size
• Small, low-profile head designed for appliance interiors

• One housing screw (ST4 x 12)

• Disconnect power before servicing the appliance and work on cool surfaces
• Use the correct screwdriver or bit to avoid stripping the head
• Install gently and avoid overtightening to prevent thread or panel damage

Fix leaking or no water flow issues with this washer water inlet tube. Replaces cracked, kinked, or damaged hoses. Straightforward installation.

This water inlet tube routes the hot water supply to the refrigerator's valve assembly, restoring proper water flow and enabling the dispenser/ice system to access hot water lines when applicable. Durable replacement for a damaged or leaking inlet line. What it does:

• Channels hot water from the household supply to the refrigerator's water valve and dispenser/ice system
• Replaces cracked, split, or corroded inlet tubing that can cause visible leaks
• Helps stop slow or intermittent water flow caused by a damaged inlet tube
• Works as part of the valve assembly plumbing to maintain safe, directed water flow

• One water inlet tube (hot)

• Turn off water supply and unplug the appliance before starting work
• Inspect fittings and O-rings; replace sealing components if damaged
• Use appropriate hand tools and avoid overtightening fittings to prevent leaks

This replacement water valve inlet tube clamp secures the refrigerator's water inlet tube to the valve to help prevent leaks and keep the line properly seated. Durable metal construction for reliable hold. What it does:

• Secures the water inlet tube to the valve so the tubing stays attached during normal use
• Helps prevent water leaks where the inlet tube meets the valve
• Keeps the tube aligned to ensure consistent water flow to the dispenser/ice maker
• Simple, low-profile clamp designed for a snug fit without crimping the tubing

• One water valve inlet tube clamp

• Turn off and disconnect power to the appliance before servicing
• Shut off the water supply and relieve any line pressure before removing the tube
• Use basic hand tools; do not overtighten the clamp to avoid damaging tubing
• After installation, restore water and power, then check connections for leaks

This water valve absorption gasket is a replacement seal that fits between the water valve and surrounding housing to maintain a watertight connection and prevent leaks. It restores a secure seal for proper valve operation and leak control. What it does:

• Creates a watertight seal at the water valve mounting interface to stop drips and seepage.
• Helps maintain correct valve alignment and prevents moisture from reaching nearby components.
• Addresses symptoms such as visible leaking at the valve, water on the cabinet floor, or moisture buildup near the valve area.
• Supports reliable water flow by preventing external leaks that can affect valve performance.

• One water valve absorption gasket

• Disconnect power and shut off water supply before servicing; relieve pressure in lines.
• Inspect mating surfaces and clean away debris or old gasket material before installing the new gasket.
• Replace only with the exact gasket specified for the valve to ensure a proper fit; hand-fit then tighten mounting fasteners to OEM guidance.

This inlet tube clamp secures the water inlet tube to the water valve, helping keep the tube seated and preventing leaks or disconnection. A small but essential part for reliable water flow into the appliance. What it does:

• Holds the inlet tube firmly to the water valve to prevent the tube from pulling off
• Helps maintain a watertight connection at the valve/tube junction
• Can stop intermittent leaks or water spray caused by a loose or shifted tube
• Keeps the inlet tube correctly positioned so water flows into the valve without obstruction

• One inlet tube clamp for the water valve

• Turn off water supply and unplug the appliance before servicing
• Use pliers or a suitable clamp tool to remove and install; ensure a snug fit without pinching the tube
• Inspect the inlet tube and valve for damage or wear while replacing the clamp

This wire tie secures wiring and small harnesses inside the appliance to prevent rubbing, snagging, or contact with moving parts. Durable and simple to use, it keeps internal wiring neat and reduces noise from loose wires. What it does:

• Fastens and groups wires or small hoses to reduce movement and chafing
• Helps prevent electrical shorts and wear caused by rubbing against panels or components
• Keeps wiring harnesses routed away from motors, belts, and heating elements
• Can reduce vibration noise from loose wiring

• Always disconnect power to the appliance before servicing electrical components
• Thread the tie through the bundle and pull snug; trim excess tail flush with a cutter
• Do not overtighten — secure wires without pinching insulation
• Replace any brittle or damaged ties; use only as directed for wire management

This user interface board is the electronic panel that allows you to select wash cycles, adjust settings, and start or pause the washer. It communicates your selections to the main control board and displays cycle status information. Replace this board if the control panel is unresponsive, buttons don't register presses, the display is blank or flickering, or error codes appear that point to a user interface fault.

Fix a washer that won't start, stops mid-cycle, or has no control panel response. This power control board manages electrical systems and signals.

This metal main board shield protects the appliance's electronic control board from heat, dust and debris. It helps maintain reliable electronics operation by shielding the board and nearby components. What it does:

• Covers and shields the main control board from heat exposure and incidental contact
• Helps prevent dust and debris buildup on the board and connections
• Can reduce risk of physical damage from nearby moving parts or panels
• Commonly replaced if the shield is bent, corroded, cracked or missing

• Disconnect power to the appliance before starting work
• Remove outer panels or access covers to reach the control board area
• Handle the shield carefully — edges may be sharp; reuse original fasteners or replace as needed

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer won't start or stops mid-cycle? This lid reed switch detects when the lid is closed and completes the safety circuit. Simple DIY fix.

This water level sensor tube connects the washer tub to the pressure switch so the machine can detect and control fill level. It restores accurate water sensing for normal cycle operation. What it does:

• Transmits air pressure from the tub to the water-level/pressure switch so the machine senses fill height
• Helps prevent overfilling or incorrect fill by ensuring the pressure switch receives a clear signal
• Replaces cracked, pinched, or deteriorated tubes that cause erratic fill behavior or washer errors
• Works as the low-pressure air line in top-load washer water-level systems

• One water level sensor tube

• Disconnect power and turn off water supply before beginning any repair
• Remove and route the tube exactly as the original to avoid kinks or sharp bends that block airflow
• Push tube ends fully onto fittings until seated; secure any retaining clips or clamps if present

Replacement spring for the washer's out-of-balance switch lever. It restores proper lever tension so the switch can correctly sense unbalanced loads and manage the spin cycle, helping reduce vibration, noise, and nuisance stops. What it does:

• Maintains the return tension on the out-of-balance switch lever so the switch actuates reliably during spin
• Allows the control to pause or redistribute when a load is unbalanced, minimizing vibration and banging
• A weak, stretched, or missing spring can cause no-spin, repeated pauses, or cycles that end early with out-of-balance warnings
• Helps ensure accurate imbalance detection for consistent spin performance

• Includes 1 spring

• Unplug the washer before servicing
• Access the out-of-balance switch lever (location varies by model; often under the top or behind the front panel)
• Note the spring's routing and attachment points; install the new spring in the same orientation and avoid overstretching
• After reassembly, run a short spin test with a small load to confirm operation

Washer won't spin or stops mid-cycle? The out of balance switch lever detects unbalanced loads and stops spinning to prevent damage. Easy DIY fix.

If your washer stops mid-spin or shakes excessively, the out of balance switch may be faulty. This part detects vibration and pauses cycles when needed.

Washer won't start or spin? This lid switch detects when the lid is closed, allowing the machine to run. Restores normal operation safely.

This rear top cover splash replaces the metal splash panel that mounts at the back of the cooktop to protect the wall and controls from spills and back splatter while restoring the appliance's finished appearance. What it does:

• Covers the rear edge of the cooktop to block grease, liquids, and food debris from reaching the wall and control area
• Restores a straight, secure rear trim if the original is bent, dented, or missing
• Helps maintain a clean cooking area and appliance appearance
• Visible damage, gaps, or a loose panel are common signs it needs replacement

• Disconnect power to the appliance before beginning work
• Removal/installation may require lifting or removing the cooktop and/or back panel and uses common hand tools (screwdriver/socket)
• Handle edges carefully—metal panels can be sharp
• Test fit and ensure fasteners are secure before returning the appliance to service

Replace your washer's cracked, broken, or damaged lid. This outer cover installs on top of the washing machine cabinet to complete the exterior.

Washer top cover panel that sits on the upper cabinet. Replace if cracked, damaged, or cosmetically worn. Restores the finished appearance of your machine.

Left side door hinge for washer models. Replaces original hinge when cracked, broken, or worn. Mounts to cabinet and supports door operation.

Replacement door hinge for your washer. Secures and supports the door panel for smooth opening and closing. Order when original is cracked or bent.

This light pipe transfers indicator or control board light to the exterior panel so status lights and icons are visible. It's the direct replacement part that restores a dim or missing control/display indicator. What it does:

• Guides LED or bulb light from the control board to the front panel or indicators
• Restores visibility when a control light appears dim, misaligned, or not visible
• Positions and protects the light source alignment for accurate indication
• Works with the existing lamp/LED and mounting points

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the light pipe gently; it's typically plastic and can crack if forced
• Remove the control panel or trim per your model's service instructions to access the part
• Reassemble carefully and test the indicator lights before finalizing the repair

Replaces the worn, cracked, or damaged front control panel console that houses user controls and display. Restores a clean interface on your washer.

Secures the washer lid hinge to the cabinet for reliable opening and closing. Replace if cracked, broken, or missing to restore proper lid alignment.

A single self-tapping screw used to secure appliance panels and trim for a stable, vibration-free fit. Replaces a lost or damaged mounting screw to restore proper part attachment and reduce rattling. What it does:

• Fastens control panels, brackets, trim pieces or small assemblies to metal or plastic surfaces
• Creates its own threads for a tight hold in sheet metal or molded openings
• Helps eliminate loose parts that can cause noise, vibration, or misalignment
• Commonly used where original screws have stripped, corroded, or been lost

• One tapping screw (quantity: 1)

• Use the correct-size Phillips or Torx driver to avoid cam-out or head damage
• Start straight and apply steady pressure; do not overtighten to prevent stripping or cracking
• Disconnect power and remove any panels before working
• If threads are damaged, replace the mating fastener or insert before installing this screw

This harness connector holder is a small plastic retainer that secures a wiring harness and connector to the appliance chassis, helping prevent wire strain and chafing for safer, more reliable operation. What it does:

• Holds wiring harness and connector in place to prevent movement and rubbing against sharp edges
• Reduces risk of loose connections that can cause intermittent electrical issues
• Keeps wiring routed neatly for easier service access and inspection
• Helps maintain proper clearances from heat-producing components

• One harness connector holder

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Replace only the damaged or missing clip; push the harness into the retainer until it snaps or seats securely
• Use a flat tool to remove old clipped retainers carefully to avoid wire damage; verify connector seating after install
• Photograph wiring before removal to ensure correct reassembly

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.