Parts for Ge GTUP270EM2WW: 01 - Controls Parts

Size: 8 - 18 ab.

This electronic control board manages the washer's core cycles and settings. When it fails, the machine may not start, respond to inputs, or complete cycles reliably. Replacing it restores proper control of wash operations.

• Directs cycle selection, timing, and motor/valve operations
• Can lead to erratic behavior such as random stopping or incorrect cycle progression
• Intermittent or dead display/indicator response can also indicate a failed board

• Disconnect power before servicing; verify capacitor discharge where applicable
• Handle the board by edges; avoid static damage by using ESD precautions
• Transfer any connectors exactly by position; label wires as needed
• After installation, run a test cycle

This terminal block and ground strap assembly provides the connection point for the incoming power cord and secures the appliance ground, restoring a safe, stable electrical connection for ranges and ovens. Use when the terminal or ground shows damage or loose wiring. What it does:

• Connects incoming power conductors to the appliance wiring and secures the chassis ground
• Provides a stable contact point to prevent intermittent power, arcing, or sparks at the cord connection
• Common replacement when terminals are loose, discolored, burned, cracked, or when the appliance has intermittent power or no power
• Restores a proper ground path when the original strap is corroded or damaged

• Always disconnect all power at the breaker or service disconnect before servicing the appliance
• Inspect surrounding insulation and wiring for heat damage; replace the block if cracked, melted, or visibly compromised

A replacement strain relief bracket that secures the appliance power cord at the entry point, protecting wiring and the terminal connection from pull and wear. Restores proper cord routing for safer, more reliable electrical connection. What it does:

• Secures the power cord where it enters the appliance to prevent tension on terminals and wiring.
• Helps reduce intermittent power, loose connections, or arcing caused by a tugged or poorly routed cord.
• Maintains correct cord routing and support to match the original mounting location and fit.
• Useful when the original bracket is cracked, broken, or no longer holds the cord firmly in place.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access is typically from the rear; remove the back access panel to reach the cord entry and terminal block.
• Remove mounting screws holding the old bracket, position the cord, and secure the new bracket without over-tightening; reuse original hardware if appropriate.
• Inspect the power cord and terminals for damage—replace damaged wiring.

Size: 8-32 t. Includes 12 screws.

This cover protects the appliance's fuse and terminal area, keeping electrical connections insulated and reducing the risk of shorting or arcing. A simple replacement restores the protective barrier over the fuse compartment. What it does:

• Shields the fuse and terminal block from debris and accidental contact
• Helps prevent electrical shorts or arcing at the fuse/terminal area
• Keeps the fuse securely positioned in its holder
• Restores the appliance's intended insulation and safety for the electrical connection

• One fuse terminal cover

• Disconnect all power to the appliance before accessing the fuse or terminal area
• Remove any mounting screws or clips holding the old cover; replace with the new cover in the same orientation
• Inspect the fuse and terminal connections for damage before reassembly; replace any damaged components as needed
• Do not operate the appliance with the fuse or terminals exposed

This fuse holder secures the appliance's thermal/fuse element and provides a stable connection point for the fuse, helping maintain proper circuit protection and reliable operation. What it does:

• Holds and secures the fuse or thermal cutoff in the appliance circuit
• Provides stable electrical contact to ensure reliable current flow
• Helps prevent intermittent power from a loose or damaged fuse connection
• Commonly replaced when the fuse or its mount is cracked, melted, or otherwise damaged

• Disconnect power to the appliance before inspecting or replacing the fuse holder
• Replace only with the correct part number for your appliance; verify fit before installation
• Use basic hand tools; avoid forcing terminals to prevent damage

This electric pressure switch senses pressure changes and sends a signal to the appliance control, restoring reliable pressure detection and normal operation. Use it when the machine fails to detect pressure or shows pressure-related errors. What it does:

• Detects changes in air/water pressure and converts them to an electrical signal for the control board
• Helps the appliance recognize correct fill, drain, or airflow conditions
• Commonly linked to symptoms such as failure to start, not filling, running continuously, or pressure-related error codes
• Replaces a failed or intermittent pressure-sensing component to restore expected cycling behavior

• Disconnect power before attempting any service to avoid shock or damage
• Label and photograph wiring before removal to ensure correct reconnection
• Test with a multimeter if troubleshooting

Includes 12 screws. Size: 8-18 ab.

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.