Parts for Kenmore 266.1532413 (2661532413, 266 1532413): Controls Parts

This washer strap assembly secures and stabilizes the component it anchors, helping control movement and noise during operation. Replacing a worn or broken strap restores proper support for smoother, quieter cycles.

• Retains and supports the attached part within the washer cabinet
• Helps limit vibration and movement, especially during spin
• Reduces rattling and knocking noises caused by loose or missing restraints
• Visual cracks, stretching, or breakage indicate it's time to replace

• Disconnect power and shut off water before servicing
• Access location per your model's service/repair guide (often requires lifting the top or removing the front panel)
• Support the component being secured while transferring/replacing the strap
• Verify secure attachment points and even support before test running a cycle

This is a replacement 8-32 trilobular hex screw used to fasten appliance panels and components. It restores secure mounting and helps eliminate loose parts or rattling caused by missing or worn fasteners. What it does:

• Secures panels, brackets, or components in place using an 8-32 trilobular thread form
• Helps prevent vibration, rattling, and loose connections when fasteners are missing or stripped
• Designed to match OEM thread style for proper engagement and retention
• Used wherever a small hex-head machine screw is required for assembly

• Use the correct driver/socket to avoid rounding the hex head
• Tighten to snug fit; avoid over-torquing which can strip threads or damage parts
• If replacing a stripped hole, inspect mating threads and consider a thread repair or alternate fastening method
• Disconnect power to the appliance before accessing internal components to reduce risk of shock or injury

This electronic control board assembly is the washer's central controller, managing cycle selection, timing, and communication with key components. Replacing a failed board can restore proper operation and dependable cycle performance. What it does

• Interprets user inputs and sensor signals to run wash, rinse, and spin sequences
• Sends power and control signals to the motor, drain pump, water valves, and lid/lock as designed
• Controls cycle timing, speeds, and status indicators
• Symptoms may include: washer won't power on or start, unresponsive controls, cycle won't advance or stops mid-cycle, or error codes/blinking lights

• One electronic control board assembly

• Disconnect power before servicing; verify no voltage is present
• Handle the PCB by the edges and use ESD protection
• Photograph/label wiring; transfer connectors to the new board one at a time
• Secure the board in the original mounts; some models may require configuration per service instructions

A small replacement hose clip that secures flexible appliance hoses to fittings to help prevent leaks and disconnections. Fits commonly used appliance hose connections to restore a secure seal and reliable water flow. What it does:

• Secures a water or drain hose to a barb or fitting to prevent the hose from coming loose
• Helps stop leaks and drips caused by loose or slipping hoses
• Prevents hose movement and rubbing that can lead to wear or abrasion
• Useful when a hose slips off during operation or after maintenance

• Disconnect power and shut off the water supply before servicing the appliance
• Use appropriate hand tools (needle-nose pliers or hose clamp pliers) to open and seat the clip
• Position the clip over the fitting and tighten until the hose is snug and secure; avoid over-tightening
• Replace only with the correct OEM-style clip for a proper fit

This terminal block and ground strap assembly provides the connection point for the incoming power cord and secures the appliance ground, restoring a safe, stable electrical connection for ranges and ovens. Use when the terminal or ground shows damage or loose wiring. What it does:

• Connects incoming power conductors to the appliance wiring and secures the chassis ground
• Provides a stable contact point to prevent intermittent power, arcing, or sparks at the cord connection
• Common replacement when terminals are loose, discolored, burned, cracked, or when the appliance has intermittent power or no power
• Restores a proper ground path when the original strap is corroded or damaged

• Always disconnect all power at the breaker or service disconnect before servicing the appliance
• Inspect surrounding insulation and wiring for heat damage; replace the block if cracked, melted, or visibly compromised

A replacement strain relief bracket that secures the appliance power cord at the entry point, protecting wiring and the terminal connection from pull and wear. Restores proper cord routing for safer, more reliable electrical connection. What it does:

• Secures the power cord where it enters the appliance to prevent tension on terminals and wiring.
• Helps reduce intermittent power, loose connections, or arcing caused by a tugged or poorly routed cord.
• Maintains correct cord routing and support to match the original mounting location and fit.
• Useful when the original bracket is cracked, broken, or no longer holds the cord firmly in place.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access is typically from the rear; remove the back access panel to reach the cord entry and terminal block.
• Remove mounting screws holding the old bracket, position the cord, and secure the new bracket without over-tightening; reuse original hardware if appropriate.
• Inspect the power cord and terminals for damage—replace damaged wiring.

Size: 8-32 t. Includes 12 screws.

This cover protects the appliance's fuse and terminal area, keeping electrical connections insulated and reducing the risk of shorting or arcing. A simple replacement restores the protective barrier over the fuse compartment. What it does:

• Shields the fuse and terminal block from debris and accidental contact
• Helps prevent electrical shorts or arcing at the fuse/terminal area
• Keeps the fuse securely positioned in its holder
• Restores the appliance's intended insulation and safety for the electrical connection

• One fuse terminal cover

• Disconnect all power to the appliance before accessing the fuse or terminal area
• Remove any mounting screws or clips holding the old cover; replace with the new cover in the same orientation
• Inspect the fuse and terminal connections for damage before reassembly; replace any damaged components as needed
• Do not operate the appliance with the fuse or terminals exposed

This electronic water level pressure switch senses air pressure from the wash tub and tells the control when to start and stop filling. Replacing a failed switch restores proper fill levels and helps cycles advance reliably. What it does:

• Monitors tub water level via an air hose connected to the switch
• Signals the control to start/stop the inlet valves at the correct level
• Enables cycle progression by confirming empty/full status
• Common symptoms: won't stop filling, stops filling too soon, incorrect water level, or water-level error codes

• 1 electronic pressure switch

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or rear cabinet area (location varies by model)
• Move the pressure hose and wire connector(s) over one at a time; ensure airtight hose fit and proper routing without kinks
• Inspect the hose and air dome for cracks, kinks, or blockages; clear or replace if needed

Includes 12 screws. Size: 8-18 ab.

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.