Parts for Crosley CDG2000FW1: Controls / Top Panel Parts

This Knob is an OEM part for Frigidaire dryers. This component is an essential part of the dryer's control panel, allowing you to select and adjust various settings and cycles. It provides a tactile and user-friendly interface for operating the dryer.

Causes of a bad knob can include wear and tear, accidental damage, or improper handling.

Symptoms of a bad knob may include:

• Cracks, breakage, or detachment from the control panel.
• Difficulty in turning or adjusting the settings.
• Inaccurate selection of desired settings.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

The Turn Start Switch is an OEM part for Frigidaire dryers. It is responsible for initiating the drying cycle when the switch is turned. This switch is a critical component that engages the dryer’s motor and starts the drying process, ensuring your clothes are dried effectively.

You should replace the turn start switch if it becomes faulty or unresponsive. Causes of a bad start switch can include regular wear and tear from frequent use, electrical issues, or damage due to excessive force or mishandling.

Symptoms of a bad turn start switch include:

• Dryer not starting when the switch is turned
• Intermittent starting issues
• The switch feeling loose or not engaging properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This console is the exterior control-panel trim that covers and supports the appliance's controls and display, restoring a clean finished look and access to the control area. What it does

• Replaces a cracked, warped or severely scratched control-panel trim piece
• Restores secure mounting and alignment for control knobs, buttons or display overlays
• Prevents debris and moisture from entering the control area through damaged trim
• Improves appearance and user access when the original console is cosmetically or structurally compromised

• High-level replacement: typically removes with basic hand tools; handle panels carefully to avoid scratching
• Disconnect power (and gas or water if appliance type requires) before starting work
• Keep screws and small fasteners organized; alignment tabs must seat properly to avoid gaps

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.