Parts for Crosley CDG2000FW1: Cabinet / Drum Parts

The Ball is an OEM part for Frigidaire dryers. This part helps the drum to rotate smoothly and evenly. It provides a stable and low-friction contact point, allowing the drum to turn efficiently during drying cycles. This is a drum-bearing ball only. For a complete drum bearing and shaft kit order 5303281153.

Causes of a bad ball can include regular wear and tear, friction from continuous drum rotation, or physical damage. 

Symptoms of a bad dryer ball include:

• Squeaking or grinding noises during operation
• The drum not rotating smoothly or becoming unbalanced
• Increased friction leading to higher energy consumption
• Visible wear or damage to the ball

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Drum Glide is an OEM part for Frigidaire dryers. It is designed to support the front of the dryer drum as it rotates, allowing the drum to turn smoothly with minimal friction and noise. This is a single glide. Your dryer uses two so it is recommended to replace both at the same time.

Causes of a bad drum glide can include wear and tear from regular use, excessive loads that put undue strain on the drum and its components, or accumulation of lint and debris that can interfere with the glide's movement.

Symptoms of a bad Drum Glide can include:

• Unusual noises, such as screeching or squealing, during operation
• Increased difficulty in turning the drum, leading to longer drying times or incomplete cycles
• Visible wear or damage to the glide itself, indicating it is time for a replacement

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This replacement screw secures appliance panels and components to restore proper fit and reduce movement. It's a simple, direct fix when small fasteners are missing, worn, or stripped and panels sit loose or rattle. What it does:

• Secures trim, panels, or internal components to keep parts aligned
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or damaged screws that prevent proper panel attachment
• Restores a safe, snug fit for covers and access panels

• Disconnect power or fuel supply before accessing the appliance for safety.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Tighten until snug; avoid over-tightening to prevent damage to threads or housing.
• Keep small parts away from children and pets during installation.

The Rear Drum Support Shaft is an OEM part for Frigidaire dryers, specifically designed to ensure the stability and smooth rotation of the dryer drum. This component plays a pivotal role in the dryer's operation by supporting the rear of the drum, allowing it to turn evenly and quietly during cycles. Note: The rear drum bearing kit is 5303281153.

The causes behind these issues often stem from normal wear and tear, excessive loads that strain the dryer's components, or lack of regular maintenance. Over time, the support shaft can wear down, become loose, or even corrode, leading to operational inefficiencies and potential damage to the dryer.

Symptoms of a failing Rear Drum Support Shaft include:

• Unusual noises, such as thumping or squeaking, during operation
• The dryer drum struggling to rotate or not rotating at all
• Increased wear on other components, such as the belt or motor, due to improper drum alignment

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This safety thermostat is a temperature-limiting switch that helps protect your refrigerator/freezer by opening the circuit if temperatures reach an unsafe level, preventing damage to components and reducing fire risk. What it does:

• Monitors internal temperature and interrupts power when the preset limit is exceeded
• Prevents overheating of heating elements or compressors in defrost and refrigeration circuits
• Helps stop continuous run or cycling caused by thermal faults
• May be used as part of the fridge/freezer safety/limit control system

• Disconnect power to the appliance before inspecting or replacing the thermostat
• Handle carefully and avoid kinking or crushing any sensing element or capillary tube
• Verify function and wiring location against your model's service manual or wiring diagram

The Inlet Thermal Fuse is an OEM part for Frigidaire laundry centers. It serves as a safety device to prevent the washer from overheating by cutting off electrical power if the temperature exceeds safe levels.

Causes of a bad inlet thermal fuse can include electrical issues such as short circuits, prolonged exposure to high temperatures, or wear and tear from regular use.

Symptoms of a bad inlet thermal fuse include:

• The washer not starting or stopping mid-cycle
• No power to the washer, even when plugged in
• Error codes indicating thermal issues
• The washer overheating during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Hex washer head ,10-32 x 0.375. Ground

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The High Temp Lubricant Tube is an OEM part for Frigidaire appliances, specifically designed to withstand and operate under high temperature conditions. This lubricant is essential for the proper maintenance and functionality of various Frigidaire appliances, offering protection against heat and friction. 

Over time, the lubricant can degrade or become contaminated, which can compromise its effectiveness. Causes of a bad high temp lubricant include exposure to extreme temperatures, accumulation of dirt and debris, or simply the natural breakdown of the lubricant over prolonged use.

Symptoms of needing a new High Temp Lubricant Tube include:

• Increased noise during appliance operation
• Reduced efficiency or performance of the appliance
• Harder movement of parts that should glide smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.