Parts for Electrolux EFMC617STT0: 04 - Controls / Top Panel Parts

Fix unresponsive buttons or blank displays with this user interface control board. Restores keypad function and display readings on your laundry center.

The Knob is an OEM part for Frigidaire dryers.This part allows you to control the settings of your dryer, enabling you to select different cycles and options for your laundry. This knob fits directly onto the dryer's interface.

Causes of a bad knob can include the knob becoming stripped, cracked, or broken from regular use, or damage resulting from excessive force being applied.  

Symptoms of a malfunctioning Knob include:

• Difficulty in turning the knob or it slipping when turned
• Inability to select or change dryer settings
• The knob coming off in your hand
• Visual signs of wear or damage on the knob

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Fix uneven drying or excess noise with this air flow diffuser. Directs airflow inside your dryer for consistent temperature and quieter operation.

This metal top panel replaces the upper rear control housing on compatible Frigidaire ranges and stoves, restoring a secure mounting surface for controls and improving cabinet fit and appearance. Ideal for repairing bent, rusted, or damaged panels. What it does

• Replaces the upper rear housing that supports control knobs, switches and the backguard area
• Restores proper alignment and spacing between the cooktop and rear controls
• Stops light leaks and relieves stress from warped or bent panels
• Commonly used when the panel is dented, rusted, cracked, or has broken mounting tabs

• One top panel

• Disconnect power (and gas, if applicable) before starting any work
• Handle sharp sheet-metal edges with gloves; panel edges can be sharp
• Remove control knobs, backguard, or trim as required and save screws for reinstallation
• Align mounting tabs and secure with original hardware; test controls after reassembly

Replaces a cracked, damaged, or worn control console on laundry centers. Restores the mounting surface for buttons, knobs, and displays to fit securely.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

The Harness is an OEM replacement part for Frigidaire clothes dryers. It consists of bundled wiring that connects control boards to other electrical components throughout the unit. 

Causes of failure include normal wear from vibration in motion, as well as damage due to cracks from over-bending during installs. Heat aging and moisture intrusion risks also increase with time.

Signs of a bad harness include:

• Dryer not powering on or not heating properly
• Intermittent reactions to control inputs  
• Frayed cables or conducting tape visible
• Electrical burning smells when operating

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic