Parts for Electrolux EFMC627UIW0: Controls / Top Panel Parts

The Board Assembly is an OEM replacement part for Frigidaire dryers. This assembly houses the main control board responsible for managing and regulating the various functions of the dryer, such as cycle selection, temperature settings, and timing operations.

Symptoms that may indicate a need to replace the board assembly include:

• The dryer not turning on or failing to respond to user inputs
• Issues with cycle selection or inability to change settings
• Error codes or warning indicators displayed related to control board malfunctions
• Inconsistent or erratic drying performance

Causes of a bad board assembly can include electrical faults, power surges, component failures due to age or overheating, or physical damage from impact or moisture exposure. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models.

The Knob Assembly is an OEM part for Frigidaire dryers. It allows you to select and adjust the dryer's settings and cycles.

A bad knob assembly can be caused by wear and tear, damage, or a faulty internal mechanism. Signs of a faulty knob assembly include the knob becoming loose, cracked, or difficult to turn.

Symptoms of a bad knob assembly can include:

• The knob becoming loose 
• Cracks or breaks in the knob
• Difficulty in turning the knob

Replace your worn-out or damaged knob assembly with this genuine OEM part to restore control over your dryer's settings. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Fix uneven drying or excess noise with this air flow diffuser. Directs airflow inside your dryer for consistent temperature and quieter operation.

This metal top panel replaces the upper rear control housing on compatible Frigidaire ranges and stoves, restoring a secure mounting surface for controls and improving cabinet fit and appearance. Ideal for repairing bent, rusted, or damaged panels. What it does

• Replaces the upper rear housing that supports control knobs, switches and the backguard area
• Restores proper alignment and spacing between the cooktop and rear controls
• Stops light leaks and relieves stress from warped or bent panels
• Commonly used when the panel is dented, rusted, cracked, or has broken mounting tabs

• One top panel

• Disconnect power (and gas, if applicable) before starting any work
• Handle sharp sheet-metal edges with gloves; panel edges can be sharp
• Remove control knobs, backguard, or trim as required and save screws for reinstallation
• Align mounting tabs and secure with original hardware; test controls after reassembly

This top panel in white restores the oven/stove's upper exterior, improving appearance and protecting internal components from spills and debris. It's a direct-replacement exterior shell piece designed to match original fit and finish. What it does:

• Replaces a cracked, warped, dented, or discolored upper cabinet panel
• Protects control housing and internal components from grease, spills, and dust
• Restores a flush, finished look to the appliance top and backguard area
• Helps maintain proper alignment for control and trim pieces

• Disconnect power to the appliance before beginning any work
• Typical removal requires removing screws and lifting the old panel straight out; keep mounting hardware
• Handle edges carefully to avoid cuts and protect the painted finish during installation

If your dryer's control panel is cracked or buttons are loose, this console assembly houses the controls and display. Restores solid mounting.

Fix dryer electrical issues or intermittent operation with this wiring harness. Restores power connections between control board and components.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic