Parts for Inglis ITW4671EW0: Controls And Water Inlet Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Rear panel for laundry center units. Covers and protects back housing. Replace if cracked, rusted, damaged, or missing for proper enclosure.

Fixes washer that won't select cycles or respond to knob input. This rotary encoder switch converts knob rotation into signals for accurate cycle selection.

Number-8, 18-thread mounting screw secures panels, brackets, and assemblies. Replace missing, stripped, or damaged screws to restore secure fitting.

Won't power on or trips breaker? This power cord restores safe electrical connection to your laundry center. Simple plug-in replacement in 10 minutes.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a control knob used on dryers, typically for the timer or cycle selector. It attaches to the timer shaft and allows you to select drying cycles and settings. Replace this knob if it is cracked, broken, or if the D-shaped mounting hole has worn out, causing the knob to spin freely without engaging the timer shaft.

This knob assembly replaces the "modifier" control knob on the console so you can adjust settings smoothly and reliably again. Restore a secure, positive-turn feel when the original knob is cracked, stripped, or missing.

• Attaches to the control shaft to select and adjust options/settings
• Replaces knobs that are cracked, broken, or missing
• Fixes a knob that spins freely, slips, or won't turn the control
• Restores proper selection and tactile feedback during use

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the flat/splines on the new knob with the shaft and press on firmly until fully seated
• The pointer aligns with the panel markings before use

If your laundry center won't start or cycle settings aren't working, this 5-position rotary switch likely needs replacement. Moderate DIY repair.

Fix a washer that won't power on or has intermittent electrical issues with this wire harness. Connects components for proper power transfer.

Fix a washer that won't fill, fills slowly, or drips when off with a new water inlet valve. Most DIYers complete this repair in 20-30 minutes.

Fix washer control issues or no power problems with this main wire harness. Routes signals between control board and motor. Moderate DIY repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.