We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Show parts
Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.
Replace your washer's control console if the panel is cracked, damaged, or missing. This console housing covers and protects the control components.
This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.
The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment.
Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.
Symptoms of a bad clip include:
This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Washer won't start or complete cycles? The electronic control board coordinates timing and modes. Moderate DIY repair—remove back panel and swap boards.
Rear panel for laundry center units. Covers and protects back housing. Replace if cracked, rusted, damaged, or missing for proper enclosure.
Usually ships within 4 - 14 days
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Fix a washer that won't fill properly or overfills with this water level pressure switch. Senses correct fill levels to restore normal wash cycles.
Washer only fills to low level or won't fill properly? This 3-level pressure switch senses water levels and signals the control to fill or advance cycles.
If your washer won't turn on or shows no power, the main power cord may be damaged or frayed. This cord restores safe electrical connection. Easy repair.
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
Symptoms of a bad screw include:
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a control knob used on dryers, typically for the timer or cycle selector. It attaches to the timer shaft and allows you to select drying cycles and settings. Replace this knob if it is cracked, broken, or if the D-shaped mounting hole has worn out, causing the knob to spin freely without engaging the timer shaft.
This knob assembly replaces the "modifier" control knob on the console so you can adjust settings smoothly and reliably again. Restore a secure, positive-turn feel when the original knob is cracked, stripped, or missing.
Fixes washer that won't select cycles or respond to knob input. This rotary encoder switch converts knob rotation into signals for accurate cycle selection.
Fix a washer that won't fill, fills slowly, or won't stop filling. This water inlet valve controls water flow during wash cycles. 30-minute repair.
Fixes intermittent power loss or control failures. This main wire harness restores electrical connections between the control board and components.
This is a push button switch used to start and stop the wash cycle on a washing machine. It mounts on the control panel and engages the machine's control circuit when pressed. Replace this button if it feels loose, does not click properly, or the washer fails to start or stop when pressed.