Parts for Ge JP968BC1BB: 01 - Cooktop Parts

This is a GE main board logic kit. The main board is the control board on below-counter models of GE ovens. When the main board malfunctions on these ovens, there are several indicators that manifest. The display area on the front of the oven door may stop working. This is also where the controls are housed. It's possible that these controls will also become unresponsive as time goes on. Use a voltage tester to make sure this is the part that is causing the problems. Unplug the oven from its power source before starting the repair. Slide the oven out from beneath the counter. Remove the back panel of the door, which will allow access to the main board. There are small screws that anchor the main board and assembly in place. Remove these screws and unplug all wires from their harnesses. Repeat these steps in reverse to install the new board kit.This board is a genuine OEM replacement part sourced directly from GE and sold individually. This part is only compatible with GE appliances.

Color: Black

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

• 1 hold-down bracket

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

This radiant element assembly replaces a failed surface heating element on compatible electric ranges, restoring reliable heat for pots and pans. It provides direct cooking heat and a stable connection to the cooktop wiring. What it does:

• Heats cookware by converting electrical energy into radiant heat at a cooktop surface
• Replaces a cracked, non-heating, or intermittently working burner element
• Restores even heating for better cooktop performance and consistent cooking results
• Works with the range's burner receptacle and surface wiring to complete the circuit

• One radiant element assembly

• Disconnect power to the range at the breaker before testing or installing
• Handle element carefully to avoid bending terminals or scratching the cooktop
• Secure connections firmly

This genuine replacement part is a radiant element for electric stoves. The radiant element is the component of the stove that heats up to allow the stove to perform its essential function of cooking. If the stove is no longer heating properly or not at all, it could mean that the radiant element needs to be replaced. Luckily this is a relatively simple process.To replace the radiant element, make sure to turn the power supply off to the stove by either unplugging it or shutting off the circuit breaker. Once powered off, proceed to locate the screws that attach the radiant element to the stove. Once identified, remove them using a screwdriver and pull up on the radiant element to release it from the stove. Once released, remove the wire harness that is connected to the radiant element and place it into the new part. Place the new radiant element on top of the stove and secure the screws that hold it in place.This OEM replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand electric stoves.

This support spring secures a stove/oven radiant heating element in place to keep the element aligned and stable during use, helping maintain reliable heating and prevent sagging or poor contact. What it does:

• Holds the radiant heating element firmly to the oven/range chassis for consistent heat distribution
• Prevents the element from shifting, sagging, or losing electrical contact
• Helps reduce arcing or intermittent heating caused by a loose element
• Common symptom: oven or burner element not staying seated, heating inconsistently, or visibly loose

• Disconnect power to the appliance before starting any repair to avoid shock.
• Remove oven racks and the heating element as needed for access; handle the element carefully to avoid damage.
• Replace only with the exact part; ensure the spring is seated correctly to secure the element.

The Clear Tape is an OEM part for GE cooktops. This specialized tape is used to secure and protect various components of the cooktop, including glass panels and control assemblies. It ensures that these components stay in place during operation and helps maintain the cooktop's structural integrity.

Causes of a bad cooktop clear tape can include exposure to high temperatures over time, wear and tear from regular use, or accidental damage during cleaning or maintenance.

Symptoms of a bad cooktop clear tape include:

• Loose or shifting glass panels
• Parts of the cooktop not staying securely in place
• Visible deterioration or peeling of the tape
• Difficulty in maintaining a stable cooktop surface

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Foam Tape is an OEM part for GE gas ranges. It serves as a sealant, ensuring a proper fit and preventing the escape of heat and gases from the range. This tape helps maintain the efficiency of the range by providing an airtight seal around various components.

Causes of a bad Foam Tape can include wear and tear over time, exposure to high temperatures, or physical damage during cleaning or maintenance. When the foam tape degrades, it can compromise the range's performance and safety.

Symptoms of a bad Foam Tape include:

• Heat escaping from the range
• Gas odors near the appliance
• Visible wear or gaps in the seal
• Decreased cooking efficiency

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement black screw used to secure interior or exterior appliance components. It provides a discrete, color-matched fastener to restore proper fit and stop rattles or loose panels. What it does

• Fastens trim, panels, brackets or control components where a small black screw is required
• Restores secure mounting to eliminate vibration, rattling or misaligned parts
• Matches finished appliance surfaces for a clean, unobtrusive look
• Simple hardware replacement for small fastener loss or damage

• One black screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver to seat the screw; avoid overtightening to prevent stripping or cracking surrounding material
• Keep track of small fasteners during disassembly and handle with care
• Replace with the exact part number if the original screw is damaged or the thread/length differs

ST10-16 X 7/16"

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

This replacement screw secures appliance components and helps keep panels, brackets, and controls firmly attached for reliable operation. It's a simple, direct fix when a mounting screw is missing, loose, or stripped. What it does:

• Fastens panels, trim, brackets or electrical components to reduce movement and rattling.
• Restores proper alignment of parts that shift when a screw is missing or worn.
• Helps maintain electrical and mechanical connections by keeping components seated.
• Common symptom: loose or vibrating panels, trim gaps, or visibly missing hardware.

• Disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Thread gently and avoid overtightening to prevent stripping the mating threads or cracking surrounding parts.
• Keep any removed hardware organized to ensure placement of all required fasteners during reassembly.

Package of 12

Black. 8-18 AB HXW 3/8

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

This standoff secures and isolates the oven power control module from the range chassis, helping keep the control electronics stable and properly spaced for safe operation. Replaces worn or broken mounting standoffs. What it does:

• Provides a stable mounting point for the power control module or control board
• Maintains proper clearance and insulation between the control and metal chassis
• Prevents movement that can cause loose connections, arcing, or intermittent control faults
• Helps reduce vibration and stress on control board components

• Disconnect power to the appliance before inspecting or replacing the standoff
• Use only the exact replacement standoff to maintain insulation and spacing
• If the control board shows damage, inspect the electronic assembly and wiring for additional issues

Cerama Bryte Cooktop Cleaner is a special cleaner designed specifically for ceramic glass and smooth-top cooking surfaces. It easily removes cooked-on foods, spills, or grease while leaving your cooktop looking like new. This product contains no abrasives or harsh chemicals, so it won’t scratch or damage your delicate cooktop surface.

To use the cleaner effectively, all you need to do is spray it onto the surface and then scrub it with a clean damp cloth. Use circular motions for best results. The product can also be used to remove baked-on foods from grates and drip pans on your stovetop. For tougher stains, let the cleaner sit for a few minutes before wiping it away.