Craftsman Edger Parts

Flange bearing for snow thrower auger and drive systems. Replace if you notice unusual noise, vibration, or difficulty operating. Verify fit with your model.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This flange bearing fits tightly between two connected components to create an airtight seal in a variety of types of lawn and garden equipment. With time and use of the equipment, the flange bearing can start to become damaged, break, or may be lost. When this occurs, the flange bearing will need to be replaced.Place the equipment on a flat surface and disconnect the spark plug wire. The location of the flange bearing will vary based on the equipment being used, so condult the user manual. Disassemble the tool as needed to get access to the flange bearing. It can be removed using a set of pliers. Clean off the components where the bearing was located before installing the new flange bearing. Replace the components and connect the spark plug wire.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold as an individual item. The flange bearing can be used with lawnmowers, edgers, and snowblowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Montgomery Wards, Yard Machines, and MTD.

This is a throttle body intended for use with lawnmowers and tractors. The throttle body is attached to the control cable, the throttle control wire, and the throttle lever. It can be damaged or wear out with regular use. Signs that the throttle body is failing or going bad include a very low idle or poor idle. Stalling of the machine when stopping the device is another indicator that the throttle body is bad. When this happens, a new throttle body must be installed.Replacing a throttle body is simple. It requires a set of pliers, a wrench, and a screwdriver. Always wear gloves when working on a throttle body repair. Make sure to allow time for the machine to cool completely before beginning the repair.This throttle bottle is an authentic OEM part. It is supplied directly from the manufacturer. The throttle body is made of high-quality, durable plastic material. It is sold as an individual unit. The throttle body is compatible with Huskee, MTD, Yard Machines, Yard-Man, and Cub Cadet brands. It can be installed in various machines, including push-behind lawn mowers, lawn tractors, and other lawn equipment."

Seals and insulates the carburetor from engine heat on lawn mowers and outdoor power equipment. Replace if cracked, worn, or causing air leaks.

Heat-blocking spacer that sits between the carburetor and engine block on outdoor power equipment. Replace if cracked, warped, or missing gasket.

This is a gasket that seals the connection between the carburetor and the engine on lawn and garden equipment. It prevents air leaks that can affect the fuel-to-air mixture and engine performance. Replace this gasket if the engine runs rough, surges, stalls, or you notice signs of an air leak around the carburetor mounting area.

Carburetor assembly for walk-behind mowers and wheeled trimmers. Replaces cracked, damaged, or worn carburetors that affect fuel mixing and delivery.

This part is a carburetor gasket. A carburetor mixes fuel and air before delivering it to the engine. The carburetor gasket creates a seal between the carburetor and cylinder that ensures that air is where it's supposed to be.The carburetor gasket may need to be replaced if the seal is broken and it is allowing air in. If there is a slight leak, the operator may notice engine roughness when it's at idle. A larger leak will cause the engine to vibrate, misfire, or hesitate under acceleration. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It it is sold individually. This carburetor gasket is compatible with engines, lawnmowers, log splitters, and trimmers manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.

Drive belt transfers power from engine to wheels on self-propelled mowers and snow blowers. Replace if slipping, worn, or cracked. Verify fit by model number.

Klik pin fastener secures wheels to tiller and snowblower assemblies. Replace if bent, broken, or missing to restore proper wheel attachment.

Replace your worn, cracked, or broken lawn mower wheel assembly. This complete wheel and tire unit installs on the deck for smooth rolling and maneuverability.

Bell washer for lawn mowers and tractors. Installs to secure components and prevent loosening. Replace if cracked, worn, or missing for proper assembly.