Craftsman Edger Carburetor

This Craftsman carburetor is the component that mixes together gas and air before the mixture can reach the engine to power a lawn trimmer. If there isn’t enough fuel in the mix, it can damage the engine or cause the trimmer not to run. Too much fuel can create excess smoke, poor performance, or can prevent the engine from starting. Testing whether a carburetor needs to be replaced can be done by adding a small amount of fuel to the component after removing the air filter. If the engine begins to run but quickly sputters out, this is an indication that the carburetor has a problem. A replacement carburetor can be installed using a wrench, pliers, and safety glasses. This trimmer component is genuine OEM and comes directly from the manufacturer. It is compatible for use with lawn trimmers by Craftsman and MTD. This is an individual item that comes with the carburetor assembly and the carburetor gasket. Pliers and screwdrivers may be needed to complete this replacement or repair.

This carburetor assembly is a genuine MTD part, sold individually. This carburetor assembly can be used as a replacement part in a variety of outdoor appliances including lawn mowers, string trimmers, and edgers. The purpose of a carburetor assembly for one of these outdoor appliances is to prepare a mixture of fuel and air in the proper ratio so that the mixture can be fed into the spark plugs to ignite them and to power on the engine as a result. If the engine is not starting, is hard starting, or if the spark plugs are not igniting properly, the carburetor may be damaged and will require replacement.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This carburetor assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Bolens, Yard Man, and MasterCut.

This replacement part is a carburetor kit. This is a genuine replacement part made by MTD. This kit is used in many types of machinery and works to ensure that the engine is running properly during use.A new carburetor kit might be needed if the current one is damaged is misplaced at all. This can be due to a single incident or from normal wear and tear. If the engine is struggling to start, it can be due to a faulty carburetor kit. Be sure the engine is completely turned off before attempting to replace this part. Work gloves are also recommended when working near or around the engine. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This is a replacement carburetor assembly that can be used for small engines, such as those found on lawn and garden equipment. The carburetor is where the air and fuel mix before going into the engine. It ensures that there is an accurate ratio of fuel and air, so the engine can start and run efficiently. While carburetors can last a long time, there is always a chance that they will need to be replaced. Normal wear and tear, damage from accidents, chemicals, or corrosion could mean a replacement is necessary. If the owner finds that their engine is sputtering, misfiring, not performing properly, or has trouble starting, the carburetor could have failed. The authentic OEM replacement carburetor features the metal body and the rubber primer bulb. It does not come with gaskets. The carburetor could be used for tillers, trimmers, and edgers. Compatible brands include Cub Cadet, MTD, Yard-Man, and Craftsman. Buyers must make sure they are buying the correct carburetor kit for their engine.

This high quality choke lever is used on string trimmers and edgers from multiple manufacturers. The plastic choke lever actuates the choke valve which creates a limit to the amount of air that can enter the engine when the equipment is cold started. If the choke lever has been damaged or is broken, it may create problems with starting the tool. If this is the case, the choke lever will need to be replaced.This is a simple replacement project that requires only a screwdriver and a pair of work gloves. Before starting, make sure the tool is turned off and the spark plug wire has been removed. Place the tool on a flat surface and take out the choke lever. The broken choke lever can be removed using the screwdriver. The new replacement choke lever can be installed before tightening the screws and using the equipment again.This is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The choke lever is made for use with edgers and string trimmers manufactured by Craftsman, Husqvarna, and Poulan.

This is a replacement carburetor for use with several types of handheld lawn and garden equipment. The carburetor is the part of the machine that is responsible for mixing the air and fuel in the right ratio before it goes into the engine. Over time, the carburetor may start to have problems. When this happens, it will mean that there is not a correct fuel and air ratio. The engine can have trouble starting, running, and it will often stall. This could be because a part of the carburetor has worn down or broken. To test the carburetor, users can remove the air filter. Then, add a teaspoon of fuel to the carb and start the engine. If it starts and then dies quickly, the carburetor could be the problem. This carburetor is a genuine OEM replacement part. It is sold individually and comes with the fuel lines and the primer bulb. It can work for many models of string trimmers and edgers. Compatible brands include MTD, Craftsman, Cub Cadet, Troy-Bilt, and Yard Machines.

This part can be used to replace a deteriorating or broken throttle linkage spring, which helps to regulate the speed of outdoor power equipment.As throttle linkage springs age they begin to wear out or can easily break. This can cause serious problems with regulating the speed of outdoor power equipment such as lawn mowers and trimmers. A broken or weak throttle linkage spring will stop the throttle on the equipment from returning to the off or resting position when the throttle is released. This can be dangerous. This throttle linkage spring is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement throttle linkage spring fits various different MTD, Cub Cadet, Craftsman, and Troy-Bilt models of lawn mowers, log splitters, and trimmers. Please note that this part is sold individually.

The primary function of a carburetor is to mix fuel and air in the right ratio. Fuel enters the carburetor through the fuel inlet fitting and then to the float bowl which delivers fuel to the other circuits. From there, the fuel goes to the needle valve, which is actuated by the float. When there is insufficient fuel, the float will stay down, keeping the valve open. Once the chamber has enough fuel, the float will go up and close the valve. A failed float bowl may leak or have too many dirt particles deposits that impede fuel flow. Luckily, you can easily replace a busted float bowl. This part is a genuine OEM Tecumseh 631867 float bowl replacement. You’ll have the assurance that this replacement is manufactured according to Tecumseh’s highest standards. It is compatible with mowers, tractors, and snowblowers from Toro, Cub Cadet, Lawn-Boy, MTD, and Tecumseh. This part is sold individually.

This is a carburetor bowl. It holds the gas that is mixed with air before it enters the engine. The carburetor bowl contains a float which regulates the amount of gas needed to mix and fuel the engine.There are times when the carburetor in of itself is considered in good working order but the bowl may be compromised. This can happen if the bowl has been corroded. Rust will damage the carburetor bowl and render it ineffective. When replacing the carburetor bowl, be sure to work in a well-ventilated area and to wear the proper gear when handling engine parts. Once the carburetor is free from the engine, unscrew the bowl from the unit over a catch pan. Any contents will fall into the pan. Disassemble the old bowl's hardware and use it when installing the new bowl.This is a genuine OEM part manufactured by Tecumseh. It is compatible for Toro, Cub Cadet, and MTD engines.

This part is an inlet needle. This inlet needle works like a valve to transport fuel into the carburetor bowl when the bowl has drained and then stops fuel intake when the carburetor bowl is full. A new inlet needle may be needed if the fuel is not flowing into the bowl as it is supposed to. This can be evident if the carburetor floods or if the engine does not have enough fuel when it's operating at high speeds. A visual inspection of the inlet needle can also be a good indicator of whether or not it needs to be replaced. If any physical signs of damage are present, the inlet needle will need to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine Tecumseh part and is an OEM part sourced directly from the manufacturer and it is sold individually. This inlet needle is compatible with snowblowers manufactured by Tecumseh and Toro.

The float shaft and pin are a genuine replacement for select Tecumseh carburetors on small lawn and garden equipment engines. The float shaft and pin are responsible for maintaining the fuel level within the carburetor. Over time because of repetitive motion, the float pin and shaft can break or become damaged, which will stop the carburetor from functioning properly. If the carburetor cannot function, the engine will not be able to perform. If left unattended, the engine and carburetor could fail completely or bigger issues could occur. Replacing the float is essential to getting the equipment back in order. This genuine float shaft and pin is designed for use on machines from Tecumseh, Poulan, Husqvarna, Lawn Boy, Cub Cadet, MTD, and Craftsman, and is compatible with a number of models. The fuel system should be drained and the engine should be cool before any engine repairs are started. Always wear gloves for hand protection. This float shaft and pin are made of durable materials and sold as a unit. No additional hardware or parts are included.

Carburetors must have tight seals to prevent too much air from getting into the carburetor at one time. If there are issues with a welch plug, it could cause an engine to lose power or to run rough. The plug might have lost its seal, it could have cracked, or it could have become lost. Sometimes, the vibration of the engine is enough to cause a plug to fall out if it is not tightly sealed. A loose fit will cause problems with the flow of fuel. This genuine OEM welch plug is sold individually and can help to seal your carburetor so your engine retains power. The part can be used with a range of lawn tractors, lawnmowers, snowblowers, and small engines. Compatible brands include Tecumseh, Lawn-Boy, Toro, Craftsman, and MTD.