Craftsman Hedge Trimmer Parts

Fuel pickup filter draws gas from tank to carburetor. Replace if engine won't start or runs poorly due to clogged filter. Verify fit with your model number.

Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.

Black plastic wheel hub cap for lawn tractors and riding mowers. Replaces cracked, broken, or missing hub caps. Snaps onto wheel hub for a finished look.

Ignition module for gas leaf blowers and trimmers. Works with flywheel to create spark timing. Replace if damaged by heat exposure or engine won't spark.

If your chainsaw rope won't retract after pulling, the starter spring likely needs replacement. This spring creates the recoil to start the engine.

Engine piston kit for gas trimmers and outdoor equipment. Replaces worn, damaged, or corroded pistons that cause poor compression and engine performance.

This OEM replacement push cap can be used in a variety of lawn and garden equipment. The push cap is secured to the end of a shaft, providing protection to the user from the sharp metal edge of the shaft. The push caps that are included with the machines may wear out over time or fall off in some cases, creating an injury risk involving sharp metal edges. These push caps are high-quality and made from durable plastic. They are easy to install. The OEM push cap is a genuine part made by the original manufacturer, to ensure quality and s proper fit. The push caps can be used on lawn tractors, chippers, shredders, log splitters, and other equipment. Some of the brands that this push cap is compatible with include MTD, Husky, Yard-Man, Bolens, Troy-Bilt, Ryobi, Yard Machines, and cub Cadet.

Primer bulb assembly kit for chainsaws. Installs on the carburetor to circulate fuel for easier starting. Replace if bulb is cracked, hardened, or worn.

Replacement bump cap for line trimmers. Secures the spool and bumper inside the housing. Replace if cracked, broken, or missing to protect the line spool.

The carburetor kit has a metal body that is designed to withstand high temperatures, a rubber primer bulb, and a plastic throttle lever. The carburetor is an integral part of engines in lawn and garden equipment. This is where the air and fuel will be mixed before being sent into the engine. The air comes in through the intake tube, and it flows into a smaller tube, where the fuel is injected through small holes in the carburetor body. Then, the two are mixed and released into the engine through a butterfly valve, which controls the amount of fuel going to the engine for optimal performance. The carburetor can become clogged over time or even be broken or damaged. If the engine is not running properly, the carburetor may need to be replaced. This is a simple replacement that only requires a screwdriver. Make sure to always disconnect the spark plug and wear gloves when performing engine repairs. This kit can be used with several models of lawn and garden equipment, including brands like Weed Eater, Paramount, Poulan, Jonsered, and Husqvarna.

Piston ring seals the space between piston and cylinder wall in gas-powered outdoor power equipment engines. Replace if worn, cracked, or causing smoke.

This extension spring attaches to the axle support bracket and the drive belt idler pulley on many types of lawn and garden equipment. It creates additional tension to the drive belt idler pulley. Sometimes the extension spring can be stretched out or may break, often caused through excess use. If this is the case, the spring will need to be replaced.If the spring is broken or no longer creates the appropriate amount of tension, replacement is required. It is an easy process that only requires a set of pliers. The pliers can be used to take the old spring off of the yard equipment before attaching the new extension spring. Make sure the equipment is on a stable surface and powered off when working with it. Remove the spark plug wire to prevent accidents.This extension spring is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The spring is made to be used with lawnmowers, lawn tractors, and tillers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

Hex flange bearing supports rotating shafts in riding mowers and tractors. Replace when you notice grinding noise or rough rotation. Verify fit with your model.

Engine won't engage when pulling starter rope? The starter pawl bridge connects the flywheel to spin your trimmer's engine. Easy DIY repair.

Seals the carburetor adapter to prevent dirt and debris from entering your chainsaw engine. Replace if cracked, brittle, or leaking. Confirm fit by model.

This ball bearing and seal are used in a range of chainsaw models. It acts as part of the blade assembly and is designed to both lessen friction and stabilize moving parts. This bearing is also set within a race and the entire race/bearing/seal assembly must be replaced at the same time. The bearing is encased with a rubber seal, which prevents fuel leakage and keeps the engine working smoothly. It does not impede the bearing as it turns. Ball bearings are placed in high contact areas and wear down due to friction. They need to be regularly replaced for optimal performance. If the engine shows difficulty while running, or is louder than usual, the seal or bearing may have worn down. This OEM replacement part is sourced from the manufacturer and works with certain models of Poulan small engines, including the Poulan/Poulan Pro 2900, and Husqvarna chainsaws. This part replaces parts 530019259 and 530047827, both of which are obsolete.