Craftsman Hedge Trimmer Parts

Vibration-dampening spring assembly that installs between the engine and handle. Replace if springs are broken, worn, or missing to restore proper isolation.

Replacement fuel cap for hedge trimmers and leaf blowers. Seals the fuel tank to prevent gasoline leaks. Replace if cracked, broken, or worn threads.

Replacement cutting blade for hedge trimmers. Metal teeth contact cutting surface and can break, chip, or wear over time. Installs on trimmer head.

Piston ring seals the gap between piston and cylinder wall in small engine equipment. Replace if worn, cracked, or causing compression loss.

This replacement carburetor kit is a genuine OEM parts kit for Craftsman hedge trimmers. The carburetor takes gasoline from the fuel line and mixes it with air from the intake valve to make a balanced fuel that is ready for combustion. Depending on how much fuel or air pass into the carburetor, the engine may run faster or slower. The most common reason for a carburetor to break down is if it is clogged with engine gunk. While it is sometimes possible to clean out a carburetor, if left for too long, the damage can be irreparable and the part will need replacing. First, remove the air filter and filter housing using a socket wrench. This will give access to the damaged carburetor and make it easier to unhook from the links that hold it in place. Be sure to set the gaskets firmly in place and then reassemble with the new part. This replacement carburetor is designed for use only with Craftsman appliances. It comes sourced directly from the original manufacturer and includes a carburetor and two gaskets.

This extension spring attaches to the axle support bracket and the drive belt idler pulley on many types of lawn and garden equipment. It creates additional tension to the drive belt idler pulley. Sometimes the extension spring can be stretched out or may break, often caused through excess use. If this is the case, the spring will need to be replaced.If the spring is broken or no longer creates the appropriate amount of tension, replacement is required. It is an easy process that only requires a set of pliers. The pliers can be used to take the old spring off of the yard equipment before attaching the new extension spring. Make sure the equipment is on a stable surface and powered off when working with it. Remove the spark plug wire to prevent accidents.This extension spring is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The spring is made to be used with lawnmowers, lawn tractors, and tillers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

Flange bearing for lawn tractors and walk-behind mowers. Replace when you notice excessive noise, wobbling, or difficulty with blade rotation. Verify fit with your model number before ordering.

Flange bearing for lawn tractors and snow blowers. Replace if you notice excessive noise, vibration, or rough wheel rotation. Verify fit with your model.

Secures the muffler cover to the muffler on chainsaws and small engines. Replace if screw is stripped, missing, or no longer holds the cover securely.

These ignition screws are used in the ignition systems on a variety of lawn and garden equipment. The screws are made of durable metal and fasten together different parts in the ignition system. While the screws are made of high-quality material, they can experience stress, wear and tear, and impacts that will break or damage them.To replace an ignition module screw, the garden tool will need to be disassembled. First, it should be turned off and placed on a flat surface. The spark plug wire should be disconnected before making the replacement. The ignition assembly will need to be taken apart to reach the ignition module screw. Use a screwdriver to remove the old part and replace it with a new replacement screw.This is an authentic OEM replacement component that is sourced directly from the manufacturer. The part is sold as an individual unit. Each ignition module screw is designed to be used with hedge trimmers, string trimmers, leaf blowers, edgers, and pole pruners created by Craftsman, Husqvarna, Poulan, Poulan Pro, and Weed Eater.

Complete carburetor gasket kit seals fuel delivery system in chainsaws. Replace when experiencing fuel leaks, poor performance, or during carburetor rebuild.

Complete spark arrestor kit for line trimmer and blower mufflers. Replace worn, clogged, or damaged arrestor screens to prevent hot debris emission.

This replacement piston kit is designed to be used with many different types of handheld lawn and garden equipment. The pistons are important parts of the engine. The crankshaft powers the pistons, so they move up and down within the cylinder. The purpose of the pistons is to transfer the gas that expands within the cylinder. The pistons can begin to wear out over time, which means that they could fail, which will cause serious problems for engine performance. If there are issues with the piston, a replacement piston kit is essential to get the machine back up and running. When a piston goes bad, it will cause the engine power to decrease. In some cases, the engine might lose all power. Replacement will require pliers, a set of wrenches, and a screwdriver to complete. This high-quality piston kit replacement is a genuine OEM part. It is sold individually. The part can be used for pole pruners, edgers, leaf blowers, string trimmers, and hedge trimmers. Compatible brands include Weed Eater, Poulan, Poulan Pro, Husqvarna, and Craftsman.

This replacement driver spring is a genuine OEM part for a string trimmer with a starter rope ignition. When an operator pulls the starter rope, the rope must recoil back into the starter assembly before it can be used again. This spring connects to a driver pulley in the starter assembly and maintains the right amount of tension needed to recoil the pulley. Over time, driver springs will begin to lose some of their tension. This is especially true if the operator is quite rough on their appliance. Pulling too hard on the starter rope can wear out the spring more quickly, making it less effective. Without a properly tensed driver spring, the starter rope will not recoil into the assembly. To change out the spring, use a nut driver to open the starter assembly and remove the pulley to get access to the old spring. Carefully remove it and install the new part. This replacement driver spring is a high-quality part designed to match the exact specifications for a Husqvarna or Jonsered appliance. This part is sourced from its original manufacturer and ships individually.

This starter spring is a genuine OEM replacement part for chainsaws that operate using a starter rope. When an operator pulls the starter rope out, there is a pulley around which the rope then has to recoil. The starter spring maintains tension in the pulley so that the rope will naturally recoil. The starter spring also provides enough tension to prevent the operator from yanking the rope all the way out of the assembly. Through repeated use, and especially if an operator is rough on their appliance, the starter spring can loosen up and will no longer work as effectively. When this happens, the starter pulley will not recoil and the starter rope will hang loose from the appliance. Fortunately, switching out the starter spring is an easy repair that should only require a wrench and a pair of pliers. Be careful when pulling the old spring out. Although it isn't as tense as it once was, it still has the potential to snap back. This replacement starter spring is a high-quality part for Husqvarna, Poulan, and Weed Eater appliances, and as such, it is sourced from its original manufacturer. This part does not ship with any additional hardware.