Craftsman Log Splitter Starter

This is a recoil starter assembly, first designed for rototillers, but also used on some models of wood chippers. It measures 7 inches in diameter and has a metal housing rather than plastic. This makes it more durable, suitable for heavy-duty lawn care responsibilities. The pull cord itself is standard nylon, well suited to pulling a heavier recoil. The purpose of a recoil starter assembly is to provide a relatively low-impact way of starting the engine. Instead of turning a crank, an operator can pull a cord, which is housed inside the starter assembly. Under ordinary circumstances, this assembly will rarely need to be entirely replaced, but damage can occur due to dropping or due to pulling the cord too hard when the engine is seized. In this case, a recoil starter assembly is a drop-in repair. Unscrew the old starter assembly, seat the new one, and screw it in. This is an OEM part sourced directly from the manufacturer, and it is sold individually.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

This is a starter recoil assembly. It is used when starting small lawn equipment and other machines. It engages the flywheel. With time and use, any or all of the recoil can wear out or become damaged, including the spring, housing, rope, or pulley. If something is damaged or worn out, the entire starter recoil assembly must be replaced. Signs that the part requires a repair include an engine that won't start or has difficulty engaging.Replacing a starter recoil assembly is easy and can be done in about 15 minutes. A nut driver and screwdriver are required for the repair. Wear gloves. Make sure the equipment is completely cooled before beginning the recoil assembly replacement. After putting tension on the spring and pulley, hold the housing securely to prevent it from releasing.The starter recoil assembly is a genuine OEM-authorized replacement part. It is sold individually. The starter recoil assembly is compatible with MTD, Cub Cadet, Yard Machines, Husky, Yard-Man, and Troy-Bilt brands. It is a complete part that includes the housing, rope, pulley, and recoil spring. It works with small engines, lawnmowers, log splitters, trimmers, and other similar equipment.

A starter handle is a piece that works in combination with several other components to start the engine in numerous machines, including lawn equipment. It works when the user pulls the starter handle grip, attached by a mechanism to the crankshaft. It turns to start the engine. If the starter handle breaks, it will have to be replaced in order to start the machine. Starter handles can become damaged from normal use, misuse, or after an accident.Replacing the starter handle is a simple project. After locating the mechanism it attaches to, typically a sturdy rope or cord, the starter handle should be tied securely to the end of the string. Wear gloves to protect the hands during the process. Test the strength of the attachment before trying to start the machine.This starter handle is a genuine OEM replacement part. It is sold as an individual piece. This starter handle is made of durable, high-quality material. It can be used in devices from MTD, Husky, Troy-Bilt, Yard Machines, and Yard-Man. It is compatible with various lawnmowers, log splitters, trimmers, and other devices with pull start engines.

This OEM starter grip is a replacement for select Briggs & Stratton engines. The starter rope grip provides the handle that is used to pull the starter rope. When it is pulled, the starter recoil spring engages the flywheel puller, which then causes the flywheel to rotate and starts the rotation of the blade as the engine fires. The starter rope grip is made of durable plastic but it can become damaged or cracked over time. If it is broken, the rope will be unable to be pulled to engage the engine until the part is replaced. This is a genuine starter grip designed to work with a variety of lawn and garden equipment that features a Briggs & Stratton engine with a pull-start. The starter grip is sold in two pieces with the grip and a cap that snaps on once the rope has been tied inside of the handle to secure it in place. The unit is sold individually. This item does not include the rope or any additional parts.