Crosley Dryer Cap Or Cover

The Lint Screen Grille is an OEM part for Whirlpool dryers. It works with the lint screen to capture and collect lint during the drying cycle, preventing it from clogging the vent and ensuring proper airflow.

A bad dryer lint screen grille can be caused by regular wear and tear, accumulation of debris, or accidental damage. If the grille becomes cracked, broken, or warped, it can lead to lint escaping from the lint screen or obstructed airflow.

Symptoms of a bad dryer lint screen grille include:

• Lint escaping from the lint screen area.
• Reduced drying efficiency or longer drying times.
• Visible damage or warping of the grille.
• Excessive lint buildup in the venting system.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Lint Screen Housing Assembly is an OEM part for Whirlpool dryers. It houses the lint screen, which captures lint and debris from the drying cycle, preventing it from clogging the dryer vent and ensuring efficient airflow.

Causes of a bad housing assembly can include cracks or breaks due to frequent handling, wear and tear over time, or accidental impact. A faulty housing can compromise the lint screen's ability to trap lint effectively, leading to potential ventilation issues.

Symptoms of a bad lint screen housing assembly include:

• Lint screen not fitting properly
• Visible cracks or damage to the housing
• Increased lint buildup inside the dryer
• Longer drying times due to restricted airflow

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lint screen grille covers the lint filter opening inside the dryer drum. It supports the lint screen and provides a smooth surface at the opening to prevent snags, restoring proper fit and safe airflow. What it does:

• Supports and aligns the lint screen so it sits flush in the opening
• Shields the blower intake and keeps fabrics from contacting internal parts
• Provides a smooth edge to help prevent clothes from snagging or fraying
• Typical failure signs: cracked or missing grille, broken tabs, lint screen not seating properly, clothes catching near the lint opening

• 1 lint screen grille

• Disconnect power before servicing
• Open the dryer door and remove the screws securing the existing grille
• Lift out the old grille, position the new grille, and secure it with the existing screws
• Reinstall the lint screen and verify it slides smoothly and sits flush

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

This lint cover is the exterior housing that holds and protects the dryer's lint screen, helping keep lint and debris contained for safer, more efficient drying. It's a direct-replacement style part designed to restore proper lint capture. What it does:

• Holds the dryer lint screen in place so lint is collected instead of entering the cabinet
• Prevents lint and debris from falling into the blower and exhaust path
• Helps maintain proper airflow through the lint screen area
• Commonly replaced when cracked, warped, or when the screen no longer seats securely

• One lint cover (housing) as shown

• Disconnect power to the dryer before attempting service
• Access may require removing the dryer's top or front panel; keep fasteners organized
• Inspect the lint screen and surrounding seals while replacing the cover

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel