Crosley Dryer Filter

The Dryer Lint Filter is an OEM replacement part for Whirlpool electric dryers. This essential screen traps lint and debris released from tumbling clothes. Consistent filtration is key for safety and performance. This filter measures approximately 12 1/2 inches wide and 10 1/2 inches deep.

Causes of a clogged lint filter can be an accumulation of lint from regular drying cycles plugging ventilation holes. Neglecting filter cleaning allows fluff to build up rapidly.

Symptoms of a dirty lint filter include:  

• Extended drying times as airflow is restricted
• Overheating problems or melted slots in the filter housing
• Risk of dryer or clothing fires from unvented lint buildup 

This OEM replacement part is also compatible with Kenmore and Maytag models too, it removes the fire hazard of neglected cleaning. 

The Dryer Lint Filter is an OEM part for Whirlpool dryers. It is responsible for trapping lint and debris from the clothes as they dry, preventing these particles from clogging the dryer vent and ensuring efficient airflow.

Causes of a bad dryer lint filter can include regular wear and tear, damage from heat or overloading, or accumulation of lint that becomes difficult to clean. A compromised lint filter can reduce dryer efficiency and increase the risk of fire.

Symptoms of a bad Dryer Lint Filter include:

• Tears or holes in the mesh
• Difficulty in inserting or removing the filter
• Excessive lint buildup in the dryer drum or vent
• Longer drying times or overheating

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screen fits into the appliance's filtration path. It captures debris to protect internal components and helps restore proper airflow or water flow when the original screen is torn, warped, clogged, or missing.

• Filters debris to prevent it from entering sensitive components such as pumps, blowers, or valves
• Helps maintain proper airflow or water circulation for consistent performance
• Common failure signs: torn mesh, cracked or warped frame, debris bypassing the screen
• Can contribute to longer cycles, reduced performance, or recurring clogs when damaged or missing

• Disconnect power to the appliance; turn off water supply if applicable
• Access the screen location per your model's instructions; remove the old screen and clean the housing
• Seat the new screen fully, ensuring correct orientation and that any tabs/locks engage
• Reassemble and test for proper operation; check for leaks or airflow restrictions

This replacement screen filters out debris before it reaches critical components, helping maintain proper flow and overall performance. Replacing a damaged or clogged screen protects the system from blockages that can lead to poor operation. What it does:

• Traps particles to prevent clogs in passages, pumps, or valves
• Helps maintain proper water or air flow through the system
• Protects internal components from damage caused by debris
• Common signs it may need replacement: visible tears or warping, heavy buildup, recurring clogs, restricted flow, or related error codes

• 1 screen

• Disconnect power; shut off the water supply. Wear gloves and eye protection.
• Access the screen. Note orientation before removal and clean the area of any debris.
• Seat the new screen fully and evenly; do not force or bend it.
• Reassemble, restore power/water, and run a brief test to confirm proper operation and flow.

This replacement screen filters debris within your appliance to help protect internal components and maintain proper performance. A clean, intact screen supports consistent flow and reduces the risk of clogs or premature wear.

• Traps debris to help prevent clogs in the designated flow path
• Helps protect downstream parts such as valves, pumps, or passages
• A torn, missing, or clogged screen can contribute to reduced performance, unusual noises, slow flow, or error codes
• Restores proper flow when replaced with a new, clean screen

• Disconnect power and, if applicable, shut off water or gas before servicing
• Access the screen per your model's service information and note its orientation
• Clean the mating area and remove any debris before installing the new screen
• If the original screen used an O-ring or seal, transfer it if reusable or replace as needed; seat fully and check for leaks or proper operation

The Dryer Screen is an OEM replacement part specific to Whirlpool dryers. Located inside the dryer cabinet behind the drum, the screen serves as a barrier protecting the blower system and ducting from lint and debris. The screen measures approximately 21"L and 7" W

Causes of a bad Dryer Screen can include physical damage from improper handling, accumulation of lint that isn't fully removed during cleaning, or wear and tear over time. A compromised lint screen can allow debris to bypass it, potentially leading to clogs and reduced drying efficiency.

Symptoms of a bad Dryer Screen include:

• Lint buildup on clothes after drying
• Longer drying times
• The dryer overheating
• Visible tears or holes in the screen mesh

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Lint Screen is an OEM part for Whirlpool dryers. It is designed to trap lint and debris from the drying clothes, preventing these materials from clogging the dryer vent and ensuring efficient airflow.

Causes of a bad lint screen can include wear and tear over time, damage from improper cleaning methods, or the accumulation of lint and debris that is difficult to remove. The mesh can become torn or the frame can crack, which reduces its effectiveness.

Symptoms of a bad lint screen include:

• Excess lint on clothes after drying
• Longer drying times
• Overheating of the dryer
• Lint buildup in the dryer vent system

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dryer Lint Filter is an OEM part for Whirlpool dryers. This filter is designed to capture lint and debris from the clothes during the drying cycle, preventing it from clogging the dryer vent and ensuring efficient airflow. Proper maintenance of the lint filter helps improve the dryer's performance and reduces the risk of fire hazards caused by lint buildup.

Over time, the lint filter can become damaged, torn, or clogged with excessive lint and debris. Common causes of a bad lint filter include wear and tear from regular use, damage from improper cleaning, or excessive lint buildup that is difficult to remove.

Symptoms of a bad dryer lint filter include:

• Visible tears or holes in the filter
• Lint not being captured effectively, leading to clogged vents
• The dryer taking longer to dry clothes due to restricted airflow
• The filter not fitting securely in its slot

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Lint Trap is an OEM part for Frigidaire dryers. It helps in capturing lint and debris generated during the drying process, preventing them from clogging the dryer vent and exhaust system.

Causes of a clogged or faulty lint trap can include excessive lint accumulation, damage to the trap screen, or improper installation.

Symptoms of a bad lint trap may include:

• Longer drying times
• Reduced drying efficiency
• Visible lint accumulation in the dryer drum or on clothes
• Excessive heat inside the dryer

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Color: white. It measures about 13 inches wide by 11-1/2 inches high.

This EMI line filter reduces electrical interference on the incoming power to help protect the appliance's electronics and ensure stable operation. A failed filter can leave the unit dead, intermittently power-cycling, or tripping a breaker.

• Filters electromagnetic interference (EMI) on the AC line
• Helps protect the control board and other sensitive circuits
• Common symptoms: no power, intermittent power, or breaker/fuse trips when the unit starts
• Typically located near the power-cord entry or main control

• Disconnect power before servicing; allow a few minutes for any capacitors to discharge
• Note and label wire positions; move wires one at a time to the new filter
• Secure the filter to its mounting bracket and ensure the ground connection is tight
• Inspect wiring for shorts or damage before restoring power and testing

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Replacement grill trim that restores your appliance's exterior finish and helps direct airflow. Use this grill when the original piece is cracked, missing, loose, or cosmetically damaged to regain a clean, finished appearance. What it does:

• Covers and protects internal components behind the appliance front or vent area.
• Helps direct airflow and reduce drafts around the appliance opening.
• Prevents debris or fingers from contacting internal parts.
• Stops rattling or vibration caused by a bent or loose grill.
• Restores the appliance's original look when the factory grill is damaged.

• Disconnect power at the breaker and allow the appliance to cool before starting any work.
• Remove existing fasteners or clips; retain original screws if they are reusable.
• Align the new grill, then secure with the original hardware; avoid over-tightening to prevent cracking.