Crosley Range / Cooktop / Oven Parts

This stainless 30-inch door handle restores a secure, comfortable grip and a clean, factory look to the door. Use it when the original handle is loose, cracked, missing, or cosmetically damaged.

• Replaces a damaged, wobbly, or missing door handle to restore normal opening and closing
• Addresses symptoms like a loose or rattling handle, flexing under pull, or visible wear
• Stainless finish matches the original appearance on compatible units
• Sized to the manufacturer's 30-inch configuration for proper fit

• Disconnect power and allow hot surfaces to cool before servicing
• Support the door; on some models, removing the door provides better access to handle screws
• Transfer any trim/end caps and reuse existing mounting screws per your model's instructions
• Tighten screws evenly; do not overtighten to avoid damaging the door skin or glass

This is the glass panel used in the oven door window. Replace it to restore a clear view into the oven and maintain the door's proper heat barrier if the original pane is cracked, shattered, or damaged.

• Forms the viewing window and thermal barrier in the oven door
• Helps the oven retain heat for consistent cooking
• Direct replacement for a cracked, shattered, or missing pane
• Typical symptoms: visible cracks, shattered glass, rattling fragments, or reduced visibility

• Disconnect power or gas and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; handle broken glass with care
• Support the door; remove the door and any trim as outlined in your model's service information
• Transfer any reusable brackets/trim from the original glass and avoid overtightening fasteners

The Cap-Burner is an OEM replacement part for Frigidaire cooktops. It is a component located at the top of each burner element on the cooktop. The cap-burner sits directly over the burner element to distribute and maintain heat levels evenly across the heating surface. 

Causes of a bad cap-burner can include warping or distortion from excessive heat exposure over time. Wet or sticky messes can also lead to clogging or blockages.

Symptoms of a bad cap-burner include: 

• Uneven or inefficient heating of pots and pans placed on the burner surface
• Hot spots or areas of excessively high heat 
• Burner elements that do not ignite or power on as expected
• Smoke or burning smells coming from below the cap-burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This replacement light lens covers the appliance's bulb, protecting it from contact, moisture, and splashes while diffusing illumination. Replacing a cracked or missing lens restores safe, even lighting and keeps the bulb properly shielded. What it does:

• Shields the bulb from contact, moisture, and debris
• Diffuses light for more even illumination with reduced glare
• Helps protect the socket area from contamination
• Typical symptoms: cracked, warped, or missing lens; discoloration; exposed bulb; harsh or uneven lighting

• Includes: 1 light lens

• Disconnect power to the appliance before servicing; allow the lamp/area to cool completely
• Wear gloves and eye protection when handling an old or broken lens
• Remove retaining screws, tabs, or clips and note lens orientation for reassembly
• Reuse existing hardware if required; do not overtighten; restore power and test light operation

The Surface Burner Cap is an OEM part for Frigidaire ranges. It fits over the surface burner, providing a protective cover while ensuring proper gas flow and flame distribution.

A bad surface burner cap can be caused by wear and tear, damage, or improper cleaning. When the burner cap becomes faulty, it can result in issues such as uneven flames, inefficient heating, or difficulty in maintaining a consistent temperature.

Symptoms of a bad surface burner cap include:

• Uneven or flickering flames
• Difficulty in reaching desired temperatures
• Excessive gas odor during burner operation

Replace your faulty surface burner cap with this genuine OEM Frigidaire part to restore your cooktop. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a smoothtop assembly intended for use with ranges by major manufacturers. This component is located on top of the stove and protects the wiring and heating elements on the interior. The smoothtop assembly is made of strong glass. This part can become damaged and may be unsafe for use. If this happens, the smoothtop assembly will need to be replaced.A set of basic tools will be needed to replace this part. Work gloves can also be useful for preventing injuries from broken glass. First, turn off the range. Unplug it from the wall and make sure it is cool to the touch. Open the oven to remove the screws that hold the smoothtop assembly in place. Pick it up and disconnect the heating elements and wires. Next, install the new smoothtop assembly and hook back up the internal components. Plug in the appliance before use.This is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold on an individual basis. The smoothtop assembly is made to be used with ranges, ovens, and stoves created by Ikea, Frigidaire, and Crosley.

Size: 8abx3/8 - blk)

This mounting bracket secures appliance components in place to restore proper alignment and reduce movement. It provides a stable connection point to keep assemblies from shifting during normal use. What it does:

• Holds and supports a specific internal assembly or panel to prevent loosening or sagging
• Restores correct alignment when a worn or broken bracket causes parts to sit unevenly
• Reduces vibration and rattling that can occur from unsecured components
• Helps maintain safe, reliable operation by keeping fastened parts in position

• One mounting bracket

• Disconnect power to the appliance before starting any repair
• Installation typically requires common hand tools; keep original fasteners if reusable
• Inspect surrounding parts and mounting points for damage; replace any stripped threads or broken clips
• Wear gloves to protect against sharp edges and follow all safety guidelines from the appliance manufacturer

The Oven Inner Door Glass is an OEM part for Whirlpool ovens. The glass component is specially tempered to withstand high heat inside the oven cavity.

Size: 20 5/8 inches x 13 1/8 inches. For the glass measuring 22 3/8 inches x 14 inches order 74004857

Causes of a bad oven inner door glass can include small cracks or chips developing from regular door openings/closings, or microscopic defects that enlarge under repeated thermal cycling. Damage from accidental impacts is also possible.

Symptoms of a bad Oven Inner Door Glass include:

• Reduced visibility into the oven due to fogging, steam, or condensation buildup
• Cracks or fractures compromising the structural integrity of the glass
• Leaks or seal failure allowing heat to escape from around the door frame

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is the spark electrode used to ignite the gas in the oven. It creates a spark at the burner to light the flame so your oven can heat reliably.

• Generates the spark that lights the oven burner
• A failed electrode can cause no heat, delayed ignition, or the oven not lighting
• Intermittent sparking or clicking without ignition may indicate a worn or cracked tip
• Carbon buildup or damage to the ceramic insulator can prevent proper ignition

• Disconnect power and shut off gas before servicing
• Access the burner area, note wire routing, and handle the ceramic insulator carefully
• Position the electrode tip at the specified gap to the burner per service literature
• Test for proper spark and burner ignition after reassembly

This replacement oven door glass panel restores a clear, safe viewing surface when the window is cracked, shattered, or stained. It helps the door insulate properly and brings back a clean, finished appearance to your range or wall oven. What it does:

• Forms the glass viewing surface on the oven door
• Shields inner panes and insulation from spills and impact
• Aids in maintaining the door seal and stable cooking temperatures
• Typical symptoms: cracked or shattered glass, missing panel, sharp edges, or visible cosmetic damage

• One oven door glass panel

• Disconnect power and allow the appliance to cool completely before starting
• Remove the door and place it on a padded surface; keep track of screws and trim
• Transfer any brackets, nameplate, or trim pieces from the old glass as required by your model
• Wear cut-resistant gloves and handle glass carefully; tighten fasteners evenly without overtightening

This is a control panel overlay for the electronic oven control on select ranges and wall ovens. It restores clear, readable button labels and refreshes the panel appearance while shielding the control face from everyday wear.

• Provides printed legends/icons for clock, timer, and oven functions
• Adheres to the EOC face to protect it from splashes and cleaning abrasion
• Use when the original overlay is faded, peeling, bubbled, cracked, or illegible
• Model-specific layout ensures the correct key positions and markings

• Disconnect power to the appliance before beginning any disassembly
• Remove the control panel/trim to access the old overlay; retain all hardware
• Carefully peel off the old overlay and clean residual adhesive; allow the surface to dry completely
• Align the new overlay with the display and key openings and apply evenly to avoid bubbles

Color: Black. Set of 4(four).By Maytag/Magic Chef. Set of 4 black square grates for gas ranges / cooktops. Fits many brands, including Maytag, Magic Chef, Admiral, Crosley, Norge, Jenn Air and others. Matching set of chrome drip pans: 1430283.

A replacement oven rack that restores stable support for cookware and baking pans, helping maintain even cooking and safe handling. Designed to fit the original rack slots for reliable, everyday oven use. What it does

• Provides a stable shelf for cookware, bakeware and roasting pans.
• Replaces bent, rusted or damaged racks that catch or tilt during use.
• Helps restore proper airflow and consistent cooking when racks sit level.
• Visible, functional repair that avoids sliding or sticking when moving trays.

• Fits into existing oven rack slides; remove old rack by sliding out and lifting if needed.
• No tools required for typical replacement; handle with oven mitts if warm.
• Inspect rack stops and guide rails for damage before installing.
• Follow oven manufacturer safety guidelines: disconnect power or ensure appliance is cool before servicing.