Dacor Refrigerator Parts

This door bushing fits on the refrigerator hinge/closer to provide a smooth pivot point and proper door alignment. Replacing a worn bushing reduces squeaks and binding and helps the door close and seal as designed.

• Provides a low-friction bearing surface between the hinge pin/closer cam and the door
• Helps maintain correct door height and alignment to the cabinet
• Promotes smooth door swing and reliable self-closing action
• Typical wear symptoms: squeaking or grinding, binding, door sag, or poor sealing

• Disconnect power and support the door before removing hinge hardware
• Note the order/orientation of hinge parts and any shims; lift off the door carefully
• Install the new bushing on the hinge pin or in the door as shown in your model's diagram
• Reinstall, level, and verify the gasket seals evenly all around

Freezer not cooling or ice maker stopped working? This evaporator fan motor restores cold air circulation when the original hums, won't spin, or fails.

This is a drip tray that sits beneath the water and ice dispenser opening on the front of the refrigerator. It catches drips and overflow from the dispenser to prevent water from running down the front of the appliance or onto the floor. Replace this tray if it is cracked, warped, discolored, or no longer sits securely in position.

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

Replaces a cracked, warped, or missing cover on your refrigerator. Protects internal components and restores proper fit so parts stay secured.

This is a drip pan kit designed to collect condensation and defrost water from the evaporator section of the refrigerator. It sits beneath the evaporator coils to channel water toward the drain system. Replace this pan if you notice water leaking onto the floor beneath the refrigerator, pooling inside the compartment, or if the existing pan is cracked or warped.

This stop-door is a small replacement door stop that helps control how the appliance door closes and rests, restoring proper door movement and preventing over-travel or binding. What it does:

• Cushions and limits the door's travel to prevent slamming or over-rotation.
• Helps the door align and latch correctly when closing.
• Can reduce door sag or rubbing caused by a worn/missing stop.
• Addresses symptoms such as a door that closes too far, hangs unevenly, or doesn't sit flush.

• High-level, two-person recommended for larger doors; support the door before removing fasteners.
• Disconnect power (and water if applicable) and follow manufacturer safety guidance before servicing.
• Use appropriate hand tools; inspect adjacent hinges and fasteners and replace if damaged.

Replacement hinge for refrigerator doors. Mounts to cabinet and door frame to support smooth opening and closing. Needed when hinge is cracked or worn.

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

Black plastic plug that seals unused refrigerator vent openings. Replace if yours is cracked, broken, missing, or damaged to keep out debris.

Flat plain washer that distributes load and spaces hardware on appliance assemblies. Replace if worn, missing, or needed for secure fastening.

Seals the refrigerator fill tube connection to prevent water leaks. Replace if cracked, worn, or missing to keep water properly routed through cabinet.

Plastic cover that conceals the top hinge assembly on your refrigerator door. Replace if cracked, broken, or missing to restore a clean appearance.

This shutoff arm is the replacement shut-off actuator for an automatic ice maker. It stops ice production when the storage bin is full, helping prevent overflow and ensuring the ice maker cycles correctly. What it does:

• Acts as the bin-level sensor that signals the ice maker to stop making ice when the bin is full
• Prevents overfilling and ice spillage by physically blocking the ice maker's harvest cycle
• Commonly replaced when the arm is broken, bent, or fails to hold the "up" (off) position
• Restores normal tank/ice production control when functioning correctly

• One ice maker shutoff arm

• Disconnect power to the refrigerator before servicing to avoid electrical shock
• This arm typically snaps or mounts onto the ice maker assembly; handle plastic parts carefully to avoid cracking
• Test operation by manually moving the arm through its travel before reassembling the cabinet or bin

This housing encloses the temperature control components for the refrigerator's pantry drawer, protecting the thermostat or control board that regulates drawer temperature. It mounts inside or on top of the drawer compartment. Replace this housing if it is cracked, warped, or broken, which can leave the control components unprotected and potentially affect temperature regulation in the drawer.

Restores the outer housing on your refrigerator. Replaces a cracked, broken, or missing cover panel. Shields internal components from dust and debris.