Parts for Ge PFSS5RKZHSS: 01 - Dispenser Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Replace your broken or missing refrigerator clinch rivet. This small fastener securely attaches internal components and panels in your side-by-side unit.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Creates an airtight seal to keep cold air in and warm air out. Replace if torn, cracked, or leaking to restore efficiency. Verify fit by model number.

Replaces a cracked, loose, or broken fresh-food door handle on your refrigerator. Restores secure grip and straight appearance where the original mounts.

Stainless steel fastener that secures your refrigerator door handle to the door assembly. Replace when original is stripped, missing, or damaged.

Replacement door stop for refrigerators. Installs on cabinet or door hinge to limit door swing and prevent wall damage. Replace if broken or missing.

Fix a refrigerator door that won't close properly or seal correctly with this door cam closure. Restores smooth latching and proper gasket alignment.

Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.

Golden-gray shield that covers the dispenser opening on your refrigerator. Replace this trim piece if it's cracked, faded, or missing to restore appearance.

Ice spilling outside the dispenser or jamming in the chute? A cracked funnel is often the culprit. This replacement guides ice cleanly into your glass.

Refrigerator grille recess cover installs at the base front of your refrigerator. Replace if cracked, broken, or missing to restore appearance.

This small set screw secures components inside your refrigerator. Replacing a missing or stripped set screw restores a tight, reliable hold so attached parts stay aligned and are less likely to loosen or rattle during use.

• Fastens an attached part to its mounting point to prevent movement or slipping
• Helps maintain proper alignment of handles, brackets, or trim pieces
• Reduces wobble, vibration, and rattling noises caused by loose hardware
• Replaces missing, stripped, or corroded set screws

• Unplug the refrigerator and shut off water if working near door/dispenser areas
• Support the part being secured; start the screw by hand to avoid cross-threading
• Tighten with the correct driver for your model; do not overtighten to prevent stripping
• The component is secure and aligned before restoring power

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Wire harness for refrigerator dispenser recess area. Replaces damaged, frayed, or corroded wiring. Essential for maintaining electrical connections.

This thimble is a small sleeve that fits into the dryer vent opening to protect and guide the vent duct while helping maintain a secure, centered connection. It reduces wear on the duct and helps keep the vent aligned for proper exhaust flow. What it does:

• Guides and centers the dryer vent/duct at the cabinet opening to reduce rubbing and abrasion
• Helps create a consistent pathway for exhaust air to the exterior
• Minimizes gaps that can allow lint buildup or air leakage when properly seated
• Supports a secure connection between the vent duct and the appliance outlet

• One thimble

• Disconnect power to the appliance and follow manufacturer safety instructions before servicing
• Use only the fasteners or clamps specified by the appliance manufacturer; do not force oversized ducts
• Inspect surrounding area for lint and damage; replace damaged ducts or seals as needed

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

Replaces cracked, broken, or worn ice storage door in your freezer compartment. Restores the barrier that contains ice and maintains proper airflow.

Secures the door gasket to your refrigerator, ensuring an airtight seal. Replace if damaged or gasket is loose to maintain cooling efficiency.

Fix water dripping from your refrigerator dispenser with this port gasket seal. Prevents leaks and moisture at the ice/water dispenser opening. Easy DIY fix.

Fix a refrigerator door that won't stay closed or latch properly with this door latch kit. Simple repair restores secure closure and proper sealing.

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Adhesive-backed foam tape seals refrigerator panels and trim to prevent air leaks, vibration, and frost buildup. Replace when worn or damaged.

This is a mounting screw used to secure various internal or external components in the refrigerator. It is a small Phillips pan-head fastener designed for use with the specific thread and length required by the appliance. Replace this screw if the original is stripped, lost, or damaged during a repair, causing a component to be loose or improperly secured.